linux-toradex.git/drivers/iio, branch v4.9.44

iio: adc: vf610_adc: Fix VALT selection value for REFSEL bits

2017-08-16T20:43:22+00:00

commit d466d3c1217406b14b834335b5b4b33c0d45bd09 upstream.

In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].

[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf

Fixes: a775427632fd ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: light: tsl2563: use correct event code

2017-08-16T20:43:20+00:00

commit a3507e48d3f99a93a3056a34a5365f310434570f upstream.

The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two.  The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.

This is going to change userspace ABI.  Hopefully fixing this to be
what it should always have been won't break any userspace code.

Cc: Jonathan Cameron 
Signed-off-by: Akinobu Mita 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: accel: bmc150: Always restore device to normal mode after suspend-resume

2017-08-16T20:43:20+00:00

commit e59e18989c68a8d7941005f81ad6abc4ca682de0 upstream.

After probe we would put the device in normal mode, after a runtime
suspend-resume we would put it back in normal mode. But for a regular
suspend-resume we would only put it back in normal mode if triggers
or events have been requested.  This is not consistent and breaks
reading raw values after a suspend-resume.

This commit changes the regular resume path to also unconditionally put
the device back in normal mode, fixing reading of raw values not working
after a regular suspend-resume cycle.

Signed-off-by: Hans de Goede 
Reviewed-by: Srinivas Pandruvada 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: imu: inv_mpu6050: add accel lpf setting for chip >= MPU6500

2017-06-24T05:11:17+00:00

commit 948588e25b8af5e66962ed3f53e1cae1656fa5af upstream.

Starting from MPU6500, accelerometer dlpf is set in a separate
register named ACCEL_CONFIG_2.
Add this new register in the map and set it for the corresponding
chips.

Signed-off-by: Jean-Baptiste Maneyrol 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: adc: ti_am335x_adc: allocating too much in probe

2017-06-24T05:11:15+00:00

commit 5ba5b437efaa7a502eec393c045d3bf90c92c4e9 upstream.

We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.

Fixes: fea89e2dfcea ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator")
Signed-off-by: Dan Carpenter 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: proximity: as3935: recalibrate RCO after resume

2017-06-24T05:11:14+00:00

commit 6272c0de13abf1480f701d38288f28a11b4301c4 upstream.

According to the datasheet the RCO must be recalibrated
on every power-on-reset. Also remove mutex locking in the
calibration function since callers other than the probe
function (which doesn't need it) will have a lock.

Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support")
Cc: George McCollister 
Signed-off-by: Matt Ranostay 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: st_pressure: Fix data sign

2017-06-24T05:11:14+00:00

commit 1b211d48abaa0e12e6e6177c0316ff55d11fdfce upstream.

Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that
the pressure and temperature data is a 2's complement.

I'm sending this the slow way, as negative pressures on these are pretty
unusual and the nature of the fixing of multiple device introduction patches
will make it hard to apply to older kernels - Jonathan.

Fixes: 217494e5b780 ("iio:pressure: Add STMicroelectronics pressures driver")
Fixes: 2f5effcbd097 ("iio: pressure-core: st: Expand and rename LPS331AP's channel descriptor")
Fixes: 7885a8ce6800 ("iio: pressure: st: Add support for new LPS001WP pressure sensor")
Fixes: e039e2f5b4da ("iio:st_pressure:initial lps22hb sensor support")
Signed-off-by: Marcin Niestroj 
Reviewed-by: Linus Walleij 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: proximity: as3935: fix iio_trigger_poll issue

2017-06-14T13:05:59+00:00

commit 9122b54f266ddee09654fe3fbc503c1a60f4a01c upstream.

Using iio_trigger_poll() can oops when multiple interrupts
happen before the first is handled.

Use iio_trigger_poll_chained() instead and use the timestamp
when processed, since it will be in theory be 2 ms max latency.

Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support")
Signed-off-by: Matt Ranostay 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: proximity: as3935: fix AS3935_INT mask

2017-06-14T13:05:59+00:00

commit 275292d3a3d62670b1b13484707b74e5239b4bb0 upstream.

AS3935 interrupt mask has been incorrect so valid lightning events
would never trigger an buffer event. Also noise interrupt should be
BIT(0).

Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support")
Signed-off-by: Matt Ranostay 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: light: ltr501 Fix interchanged als/ps register field

2017-06-14T13:05:59+00:00

commit 7cc3bff4efe6164a0c8163331c8aa55454799f42 upstream.

The register mapping for the IIO driver for the Liteon Light and Proximity
sensor LTR501 interrupt mode is interchanged (ALS/PS).
There is a register called INTERRUPT register (address 0x8F)
Bit 0 represents PS measurement trigger.
Bit 1 represents ALS measurement trigger.
This two bit fields are interchanged within the driver.
see datasheet page 24:
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/S_110_LTR-501ALS-01_PrelimDS_ver1%5B1%5D.pdf

Signed-off-by: Franziska Naepelt 
Fixes: 7ac702b3144b6 ("iio: ltr501: Add interrupt support")
Acked-by: Peter Meerwald-Stadler 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman