* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: sentelic - fix left/right horizontal scroll mapping Input: pmouse - move Sentelic probe down the list Input: add compat support for sysfs and /proc capabilities output Input: i8042 - add Dritek quirk for Acer Aspire 5610. Input: xbox - do not use GFP_KERNEL under spinlock Input: psmouse - fix Synaptics detection when protocol is disabled Input: bcm5974 - report ABS_MT events Input: davinci_keyscan - add device_enable method to platform data Input: evdev - be less aggressive about sending SIGIO notifies Input: atkbd - fix canceling event_work in disconnect Input: serio - fix potential deadlock when unbinding drivers Input: gf2k - fix &&/|| confusion in gf2k_connect()
Add a function pointer in the platform data of the DaVinci Keyscan driver called device_enable, in order to perform board specific actions when the device is initialized, like setup the PINMUX configuration. Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to first unregister input device and only then cancel event work since events can arrive (and cause event work to get scheduled again) until input_unregister_device() returns. Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sysfs_remove_group() waits for sysfs attributes to be removed, therefore
we do not need to worry about driver-specific attributes being accessed
after driver has been detached from the device. In fact, attempts to take
serio->drv_mutex in attribute methods may lead to the following deadlock:
sysfs_read_file()
fill_read_buffer()
sysfs_get_active_two()
psmouse_attr_show_helper()
serio_pin_driver()
serio_disconnect_driver()
mutex_lock(&serio->drv_mutex);
<--------> mutex_lock(&serio_drv_mutex);
psmouse_disconnect()
sysfs_remove_group(... psmouse_attr_group);
....
sysfs_deactivate();
wait_for_completion();
Fix this by removing calls to serio_[un]pin_driver() and functions themselves
and using driver-private mutexes to serialize access to attribute's set()
methods that may change device state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: iforce - wait for command completion when closing the device Input: twl4030-pwrbutton - switch to using threaded IRQ Input: twl4030_keypad - switch to using threaded IRQ Input: lifebook - add CONFIG_DMI dependency Input: wistron - fix test for CONFIG_PM Input: psmouse - fix compile warning in hgpk module Input: matrix-keypad - handle cases when GPIOs can't be wakeup sources Input: iforce - fix oops on device disconnect Input: ff-memless - add notion of direction to for rumble effects Input: ff-memless - another fix for signed to unsigned overflow Input: ff-memless - start playing FF effects immediately Input: serio - do not mark kseriod freezable anymore Input: speed up suspend/shutdown for PS/2 mice and keyboards
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On certain boards not all GPIOs may be used as wakeup sources, in which case some of enable_irq_wake() calls will fail. On resume calling disable_irq_wake() will warn about unbalanced IRQ wake disable. Solve this by checking whether enable_irq_wake() succeeded or not and no not call disable_irq_wake() for these GPIOs/IRQs that have not been enabled. Reported-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of doing full-blown reset while suspending or shutting down the box use lighter form of reset that should take less time. Tested-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits) Input: ALPS - add interleaved protocol support (Dell E6x00 series) Input: keyboard - don't override beep with a bell Input: altera_ps2 - fix test of unsigned in altera_ps2_probe() Input: add mc13783 touchscreen driver Input: ep93xx_keypad - update driver to new core support Input: wacom - separate pen from express keys on Graphire Input: wacom - add defines for data packet report IDs Input: wacom - add support for new LCD tablets Input: wacom - add defines for packet lengths of various devices Input: wacom - ensure the device is initialized properly upon resume Input: at32psif - do not sleep in atomic context Input: i8042 - add Gigabyte M1022M to the noloop list Input: i8042 - allow installing platform filters for incoming data Input: i8042 - fix locking in interrupt routine Input: ALPS - do not set REL_X/REL_Y capabilities on the touchpad Input: document use of input_event() function Input: sa1111ps2 - annotate probe() and remove() methods Input: ambakmi - annotate probe() and remove() methods Input: gscps2 - fix probe() and remove() annotations Input: altera_ps2 - add annotations to probe and remove methods ...
This driver was merged before the ep93xx core support was added
for the keypad clock and acquiring/releasing the necessary gpio's.
Now that the proper support is in the ep93xx core this driver
needs to be updated to work correctly.
Summary of changes:
1) Remove some unused members from the platform data.
2) Remove the custom KEY macro and use the ones available in
<linux/input/matrix_keypad.h>
3) Remove the keypad_{readl/writel} macros and just use
__raw_{readl/writel} directly.
4) Update the clk_set_rate() call to work with the core support.
5) Cleanup the probe routine and remove some unneeded messages.
6) Use the ep93xx core functions to acquire and release the gpio's.
7) Fix the clk_get() call to get the keypad clock.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>