linux-toradex.git/drivers/input/misc, branch v4.14-rc7

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2017-10-22T01:46:39+00:00

Pull input fixes from Dmitry Torokhov:

 - joydev now implements a blacklist to avoid creating joystick nodes
   for accelerometers found in composite devices such as PlaStation
   controllers

 - assorted driver fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: ims-psu - check if CDC union descriptor is sane
  Input: joydev - blacklist ds3/ds4/udraw motion sensors
  Input: allow matching device IDs on property bits
  Input: factor out and export input_device_id matching code
  Input: goodix - poll the 'buffer status' bit before reading data
  Input: axp20x-pek - fix module not auto-loading for axp221 pek
  Input: tca8418 - enable interrupt after it has been requested
  Input: stmfts - fix setting ABS_MT_POSITION_* maximum size
  Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
  Input: synaptics - disable kernel tracking on SMBus devices

Input: ims-psu - check if CDC union descriptor is sane

2017-10-20T00:20:06+00:00

Before trying to use CDC union descriptor, try to validate whether that it
is sane by checking that intf->altsetting->extra is big enough and that
descriptor bLength is not too big and not too small.

Reported-by: Andrey Konovalov 
Signed-off-by: Dmitry Torokhov

Input: axp20x-pek - fix module not auto-loading for axp221 pek

2017-10-19T23:50:28+00:00

Now that we have a platform_device_id table and multiple supported ids
we should be using MODULE_DEVICE_TABLE instead of MODULE_ALIAS.

This fixes a regression on Bay and Cherry Trail devices, where the power
button is now enumerated as an "axp221-pek" and it was impossible to
wakeup these devices from suspend since the module did not load.

Fixes: c3cc94470bd3 ("Input: axp20x-pek - add support for AXP221 PEK")
Signed-off-by: Hans de Goede 
Signed-off-by: Dmitry Torokhov

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2017-09-23T03:23:41+00:00

Pull input fixes from Dmitry Torokhov:

 - fixes for two long standing issues (lock up and a crash) in force
   feedback handling in uinput driver

 - tweak to firmware update timing in Elan I2C touchpad driver.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elan_i2c - extend Flash-Write delay
  Input: uinput - avoid crash when sending FF request to device going away
  Input: uinput - avoid FF flush when destroying device

Input: uinput - avoid crash when sending FF request to device going away

2017-09-21T23:31:23+00:00

If FF request comes in while uinput device is going away,
uinput_request_send() will fail with -ENODEV, and uinput_request_submit()
will attempt to mark the slot as unused by calling uinput_request_done().
Unfortunately in this case we haven't initialized request->done completion
yet, and we get a crash:

[   39.402036] BUG: spinlock bad magic on CPU#1, fftest/3108
[   39.402046]  lock: 0xffff88006a93bb00, .magic: 00000000, .owner: /39, .owner_cpu: 1217155072
[   39.402055] CPU: 1 PID: 3108 Comm: fftest Tainted: G        W 4.13.0+ #15
[   39.402059] Hardware name: LENOVO 20HQS0EG02/20HQS0EG02, BIOS N1MET37W (1.22 ) 07/04/2017
[   39.402064]  0000000000000086 f0fad82f3ceaa120 ffff88006a93b9a0 ffffffff9de941bb
[   39.402077]  ffff88026df8ae00 ffff88006a93bb00 ffff88006a93b9c0 ffffffff9dca62b7
[   39.402088]  ffff88006a93bb00 ffff88006a93baf8 ffff88006a93b9e0 ffffffff9dca62e7
[   39.402099] Call Trace:
[   39.402112]  [] dump_stack+0x4d/0x63
[   39.402123]  [] spin_dump+0x97/0x9c
[   39.402130]  [] spin_bug+0x2b/0x2d
[   39.402138]  [] do_raw_spin_lock+0x28/0xfd
[   39.402147]  [] _raw_spin_lock_irqsave+0x19/0x1f
[   39.402154]  [] complete+0x1d/0x48
[   39.402162]  [] 0xffffffffc04f30af
[   39.402167]  [] 0xffffffffc04f468c
[   39.402177]  [] ? __slab_free+0x22f/0x359
[   39.402184]  [] ? tk_clock_read+0xc/0xe
[   39.402189]  [] 0xffffffffc04f471f
[   39.402195]  [] ? __wake_up+0x44/0x4b
[   39.402200]  [] ? 0xffffffffc04f3240
[   39.402207]  [] erase_effect+0xa1/0xd2
[   39.402214]  [] input_ff_flush+0x43/0x5c
[   39.402219]  [] 0xffffffffc04f32ad
[   39.402227]  [] input_flush_device+0x3d/0x51
[   39.402234]  [] evdev_flush+0x49/0x5c
[   39.402243]  [] filp_close+0x3f/0x65
[   39.402253]  [] put_files_struct+0x66/0xc1
[   39.402261]  [] exit_files+0x47/0x4e
[   39.402270]  [] do_exit+0x483/0x969
[   39.402278]  [] ? recalc_sigpending_tsk+0x3d/0x44
[   39.402285]  [] do_group_exit+0x42/0xb0
[   39.402293]  [] get_signal+0x58d/0x5bf
[   39.402300]  [] do_signal+0x37/0x53e
[   39.402307]  [] ? evdev_ioctl_handler+0xac8/0xb04
[   39.402314]  [] ? evdev_ioctl+0x10/0x12
[   39.402321]  [] ? do_vfs_ioctl+0x42e/0x501
[   39.402328]  [] prepare_exit_to_usermode+0x66/0x90
[   39.402333]  [] syscall_return_slowpath+0xe3/0xec
[   39.402339]  [] int_ret_from_sys_call+0x25/0x8f

While we could solve this by simply initializing the completion earlier, we
are better off rearranging the code a bit so we avoid calling complete() on
requests that we did not send out. This patch consolidates marking request
slots as free in one place (in uinput_request_submit(), the same place
where we acquire them) and having everyone else simply signal completion
of the requests.

Fixes: 00ce756ce53a ("Input: uinput - mark failed submission requests as free")
Signed-off-by: Dmitry Torokhov

Input: uinput - avoid FF flush when destroying device

2017-09-21T23:31:22+00:00

Normally, when input device supporting force feedback effects is being
destroyed, we try to "flush" currently playing effects, so that the
physical device does not continue vibrating (or executing other effects).
Unfortunately this does not work well for uinput as flushing of the effects
deadlocks with the destroy action:

- if device is being destroyed because the file descriptor is being closed,
  then there is noone to even service FF requests;

- if device is being destroyed because userspace sent UI_DEV_DESTROY,
  while theoretically it could be possible to service FF requests,
  userspace is unlikely to do so (they'd need to make sure FF handling
  happens on a separate thread) even if kernel solves the issue with FF
  ioctls deadlocking with UI_DEV_DESTROY ioctl on udev->mutex.

To avoid lockups like the one below, let's install a custom input device
flush handler, and avoid trying to flush force feedback effects when we
destroying the device, and instead rely on uinput to shut off the device
properly.

NMI watchdog: Watchdog detected hard LOCKUP on cpu 3
...
 <>  [] _raw_spin_lock_irqsave+0x37/0x40
 [] complete+0x1d/0x50
 [] uinput_request_done+0x3c/0x40 [uinput]
 [] uinput_request_submit.part.7+0x47/0xb0 [uinput]
 [] uinput_dev_erase_effect+0x5b/0x76 [uinput]
 [] erase_effect+0xad/0xf0
 [] flush_effects+0x4d/0x90
 [] input_flush_device+0x40/0x60
 [] evdev_cleanup+0xac/0xc0
 [] evdev_disconnect+0x2b/0x60
 [] __input_unregister_device+0xac/0x150
 [] input_unregister_device+0x47/0x70
 [] uinput_destroy_device+0xb5/0xc0 [uinput]
 [] uinput_ioctl_handler.isra.9+0x65e/0x740 [uinput]
 [] ? do_futex+0x12b/0xad0
 [] uinput_ioctl+0x18/0x20 [uinput]
 [] do_vfs_ioctl+0x298/0x480
 [] ? security_file_ioctl+0x43/0x60
 [] SyS_ioctl+0x79/0x90
 [] entry_SYSCALL_64_fastpath+0x12/0x71

Reported-by: Rodrigo Rivas Costa 
Reported-by: Clément VUCHENER 
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=193741
Signed-off-by: Dmitry Torokhov

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2017-09-16T18:24:26+00:00

Pull more input updates from Dmitry Torokhov:
 "A second round of updates for the input subsystem:

   - a new driver for PWM-controlled vibrators

   - ucb1400 touchscreen driver had completely busted suspend/resume
     handling

   - we now handle "home" button found on some devices with Goodix
     touchscreens

   - assorted other fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - add Gigabyte P57 to the keyboard reset table
  Input: xpad - validate USB endpoint type during probe
  Input: ucb1400_ts - fix suspend and resume handling
  Input: edt-ft5x06 - fix access to non-existing register
  Input: elantech - make arrays debounce_packet static, reduces object code size
  Input: surface3_spi - make const array header static, reduces object code size
  Input: goodix - add support for capacitive home button
  Input: add a driver for PWM controllable vibrators
  Input: adi - make array seq static, reduces object code size

Merge branch 'next' into for-linus

2017-09-15T16:52:21+00:00

Prepare second round of input updates for 4.14 merge window.

Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

2017-09-07T20:51:13+00:00

Pull MFD updates from Lee Jones:
 "New Drivers
   - RK805 Power Management IC (PMIC)
   - ROHM BD9571MWV-M MFD Power Management IC (PMIC)
   - Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs

  New Device Support:
   - Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
   - Add support for X-Powers AXP806 to axp20x
   - Add support for X-Powers AXP813 to axp20x
   - Add support for Intel Sunrise Point LPSS to intel-lpss-pci

  New Functionality:
   - Amend API to provide register layout; atmel-smc

  Fix-ups:
   - DT re-work; omap, nokia
   - Header file location change {I2C => MFD}; dm355evm_msp, tps65010
   - Fix chip ID formatting issue(s); rk808
   - Optionally register touchscreen devices; da9052-core
   - Documentation improvements; twl-core
   - Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
   - Drop unnecessary static declaration; max8925-i2c
   - Kconfig changes (missing deps and remove module support)
   - Slim down oversized licence statement; hi6421-pmic-core
   - Use managed resources (devm_*); lp87565
   - Supply proper error checking/handling; t7l66xb

  Bug Fixes:
   - Fix counter duplication issue; da9052-core
   - Fix potential NULL deference issue; max8998
   - Leave SPI-NOR write-protection bit alone; lpc_ich
   - Ensure device is put into reset during suspend; intel-lpss
   - Correct register offset variable size; omap-usb-tll"

* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
  mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
  mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
  dt-bindings: mfd: Add bindings for ZII RAVE devices
  mfd: omap-usb-tll: Fix register offsets
  mfd: da9052: Constify spi_device_id
  mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
  mfd: da9055: Constify i2c_device_id
  mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
  mfd: t7l66xb: Handle return value of clk_prepare_enable
  mfd: Add ROHM BD9571MWV-M PMIC DT bindings
  mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
  mfd: lp87565: Convert to use devm_mfd_add_devices()
  mfd: Add support for TPS68470 device
  mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
  mfd: syscon: atmel-smc: Add helper to retrieve register layout
  mfd: axp20x: Use correct platform device ID for many PEK
  dt-bindings: mfd: axp20x: Introduce bindings for AXP813
  mfd: axp20x: Add support for AXP813 PMIC
  dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
  mfd: Add ROHM BD9571MWV-M MFD PMIC driver
  ...

Merge branches 'ib-mfd-arm-i2c-4.14', 'ib-mfd-arm-usb-video-4.14', 'ib-mfd-hwmon-4.14', 'ib-mfd-iio-pwm-4.14', 'ib-mfd-input-rtc-4.14', 'ib-mfd-many-4.14' and 'ib-mfd-pinctrl-regulator-4.14' into ibs-for-mfd-merged

2017-09-05T07:45:36+00:00