This patch fixes a spelling error found in Kconfig.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync with mainline to get in trackpoint updates and other changes.

Since AVR32 arch is gone, atmel-wm97xx driver is useless. In theory it
could have been rewritten to work with AT91 devices, but the driver is from
the platform data era, and a bit hard coded to work on AVR32 hardware
variant of the AC97C peripheral, so let's remove it.

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull input updates from Dmitry Torokhov:

 - three new touchscreen drivers: EETI EXC3000, HiDeep, and Samsung
   S6SY761

 - the timer API conversion (setup_timer() -> timer_setup())

 - a few drivers swiytched to using managed API for creating custom
   device attributes

 - other assorted fixed and cleanups.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (50 commits)
  Input: gamecon - mark expected switch fall-throughs
  Input: sidewinder - mark expected switch fall-throughs
  Input: spaceball - mark expected switch fall-throughs
  Input: uinput - unlock on allocation failure in ioctl
  Input: add support for the Samsung S6SY761 touchscreen
  Input: add support for HiDeep touchscreen
  Input: st1232 - remove obsolete platform device support
  Input: convert autorepeat timer to use timer_setup()
  media: ttpci: remove autorepeat handling and use timer_setup
  Input: cyttsp4 - avoid overflows when calculating memory sizes
  Input: mxs-lradc - remove redundant assignment to pointer input
  Input: add I2C attached EETI EXC3000 multi touch driver
  Input: goodix - support gt1151 touchpanel
  Input: ps2-gpio - actually abort probe when connected to sleeping GPIOs
  Input: hil_mlc - convert to using timer_setup()
  Input: hp_sdc - convert to using timer_setup()
  Input: touchsceen - convert timers to use timer_setup()
  Input: keyboard - convert timers to use timer_setup()
  Input: uinput - fold header into the driver proper
  Input: uinput - remove uinput_allocate_device()
  ...

The S6SY761 touchscreen is a capicitive multi-touch controller
for mobile use. It's connected with i2c at the address 0x48.

This commit provides a basic version of the driver which can
handle only initialization, touch events and power states.

The controller is controlled by a firmware which, in the version
I currently have, doesn't provide all the possible
functionalities mentioned in the datasheet.

Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The HiDeep touchscreen device is a capacitive multi-touch controller
mainly for multi-touch supported devices use. It use I2C interface for
communication to IC and provide axis X, Y, Z locations for ten finger
touch through input event interface to userspace.

It support the Crimson and the Lime two type IC. They are different
the number of channel supported and FW size. But the working protocol
is same.

Signed-off-by: Anthony Kim <anthony.kim@hideep.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The 3000 series have a new protocol which allows to report up to 5 points
in a single 66 byte frame. One must always read in 66 byte frames.
To support up to 10 points, two consecutive frames need to be read:
The first frame says how many points until sync.
The second frame must say zero points or both frames must be discarded.

To be able to work with the higher 400KHz I2C bus rate, one must
successfully send a special package prior _each_ read or the controller
will refuse to cooperate.

This is a minimal implementation based on egalax_i2c.c (which can be found
on the internet) and egalax_ts.c but without the vendor interface and no
power management support.

Signed-off-by: Ahmet Inan <inan@distec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Change control of TOUCHSCREEN_USB_EASYTOUCH prompt string from
EMBEDDED to EXPERT to match the rest of this Kconfig file.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This adds support for the new AC97 bus code, which discovers the devices
rather than uses platform data.

As part of this discovery, it enables a multi-function device wm97xx,
which supports touchscreen, battery, ADC and an audio codec. This patch
adds the code to bind the touchscreen "cell" as the touchscreen driver.

This was tested on the pxa architecture with a pxa270 + wm9713 + the
mioa701 touchscreen.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The stmfts (ST-Microelectronics FingerTip S) touchscreen device is a
capacitive multi-touch controller mainly for mobile use.  It's connected
through i2c bus at the address 0x49 and it interfaces with userspace
through input event interface.

At the current state it provides a touchscreen multitouch functionality up
to 10 fingers. Each finger is enumerated with a distinctive id (from 0 to
9).

If enabled the device can support single "touch" hovering, by providing
three coordinates, x, y and distance.

It is possible to select the touchkey functionality which provides a basic
two keys interface for "home" and "back" menu, typical in mobile phones.

Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>