linux-toradex.git/drivers/interconnect/qcom, branch v5.11-rc3

interconnect: qcom: fix rpmh link failures

2020-12-28T12:03:02+00:00

When CONFIG_COMPILE_TEST is set, it is possible to build some
of the interconnect drivers into the kernel while their dependencies
are loadable modules, which is bad:

arm-linux-gnueabi-ld: drivers/interconnect/qcom/bcm-voter.o: in function `qcom_icc_bcm_voter_commit':
(.text+0x1f8): undefined reference to `rpmh_invalidate'
arm-linux-gnueabi-ld: (.text+0x20c): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: (.text+0x2b0): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: (.text+0x2e8): undefined reference to `rpmh_write_batch'
arm-linux-gnueabi-ld: drivers/interconnect/qcom/icc-rpmh.o: in function `qcom_icc_bcm_init':
(.text+0x2ac): undefined reference to `cmd_db_read_addr'
arm-linux-gnueabi-ld: (.text+0x2c8): undefined reference to `cmd_db_read_aux_data'

The exact dependencies are a bit complicated, so split them out into a
hidden Kconfig symbol that all drivers can in turn depend on to get it
right.

Fixes: 976daac4a1c5 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Arnd Bergmann 
Reviewed-by: Bjorn Andersson 
Link: https://lore.kernel.org/r/20201204165030.3747484-1-arnd@kernel.org
Signed-off-by: Georgi Djakov

Merge tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2020-12-17T00:27:35+00:00

Pull ARM device tree updates from Arnd Bergmann:
 "Across all platforms, there is a continued move towards DT schema for
  validating the dts files. As a result there are bug fixes for mistakes
  that are found using these schema, in addition to warnings from the
  dtc compiler.

  As usual, many changes are for adding support for additional on-chip
  and on-board components in the machines we already support.

  The newly supported SoCs for this release are:

   - MStar Infinity2M, a low-end IP camera chip based on a dual-core
     Cortex-A7, otherwise similar to the Infinity chip we already
     support. This is also known as the SigmaStar SSD202D, and we add
     support for the Honestar ssd201htv2 development kit.

   - Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
     (BMC), in the same family as the NPCM750. This gets used in the
     Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
     which are added as well.

   - Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
     Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
     GT-AC5300 high-end WiFi router based on this chip.

   - Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
     meant for faster Chromebooks and tablets. It gets added along with
     its reference design.

   - Mediatek MT6779 (Helio P90) is a high-end phone chip from last
     year's generation, also added along with its reference board. This
     one is still based on Cortex-A75/A55.

   - Mediatek MT8167 is a version of the already supported MT8516 chip,
     both based on Cortex-A35. It gets added along with the "Pumpkin"
     single board computer, but is likely to also make its way into
     low-end tablets in the future.

  For the already supported chips, there are a number of new boards.
  Interestingly there are more 32-bit machines added this time than
  64-bit. Here is a brief list of the new boards:

   - Three new Mikrotik router variants based on Marvell Prestera
     98DX3236, a close relative of the more common Armada XP

   - A reference board for the Marvell Armada 382

   - Three new servers using ASpeed baseboard management controllers,
     the actual machines being from Bytedance, Facebook and IBM, and one
     machine using the Nuvoton NPCM750 BMC.

   - The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.

   - The usual set of 32-bit i.MX industrial/embedded hardware:
       * Protonic WD3 (tractor e-cockpit)
       * Kamstrup OMNIA Flex Concentrator (smart grid platform)
       * Van der Laan LANMCU (food storage)
       * Altesco I6P (vehicle inspection stations)
       * PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard

   - DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
     aleady supported DHCOM module

   - Three new Allwinner SoC based single-board computers:
       * NanoPi R1 (H3 based)
       * FriendlyArm ZeroPi (H3 based)
       * Elimo Initium SBC (S3 based)

   - Ouya Game Console based on Nvidia Tegra 3

   - Version 5 of the already supported Zynq Z-Turn MYIR Board

   - LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
     is a repackaged 16-core LX2160A

   - A series of Kontron i.MX8M Mini baseboard/SoM versions

   - Espressobin Ultra, a new variant of the popular Armada 3700 based
     board,

   - IEI Puzzle-M801, a rackmount network appliance based on Marvell
     Armada 8040

   - Microsoft Lumia 950 XL, a phone

   - HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
     sm8150, respectively

   - Three new board variants of the "Trogdor" Chromebook (sc7180)

   - New board variants of the Renesas based "Kingfisher" and "HiHope"
     reference boards

   - Kobol Helios64, an open source NAS appliance based on Rockchips
     RK3399

   - Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
     carrier boards"

* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
  arm64: dts: sparx5: Add SGPIO devices
  arm64: dts: sparx5: Add reset support
  dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
  ARM: mstar: SMP support
  ARM: mstar: Wire up smpctrl for SSD201/SSD202D
  ARM: mstar: Add smp ctrl registers to infinity2m dtsi
  ARM: mstar: Add dts for Honestar ssd201htv2
  ARM: mstar: Add chip level dtsi for SSD202D
  ARM: mstar: Add common dtsi for SSD201/SSD202D
  ARM: mstar: Add infinity2m support
  dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
  dt-bindings: vendor-prefixes: Add honestar vendor prefix
  dt-bindings: mstar: Add binding details for mstar,smpctrl
  ARM: mstar: Fill in GPIO controller properties for infinity
  ARM: mstar: Add gpio controller to MStar base dtsi
  ARM: zynq: Fix incorrect reference to XM013 instead of XM011
  ARM: zynq: Convert at25 binding to new description on zc770-xm013
  ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
  ARM: zynq: Fix leds subnode name for zc702/zybo-z7
  ARM: zynq: Rename bus to be align with simple-bus yaml
  ...

Merge tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

2020-12-08T22:50:08+00:00

Qualcomm ARM64 DT updates for 5.11

For SM8250 the recently introduced support for handling boot-loader
stream mappings in the ARM SMMU allow us to enable this, and thereby USB
controller and PHY, SDHCI controller and FastRPC, as well as support for
the SM8250 HDK board has been added. Additionally PRNG and RTC is
enabled.

Similarly for SM8150, the ARM SMMU could be added which allows the
secondary USB controller and PHYs, as well as WiFi to be added and
support for the SM8150 HDK board to be introduced. Additionally
Coresight and support for the last-level cache controller was added.

MSM8916 finally has VDDCX and VDDMX removed as regulators and are now
handled by the rpmpd driver for the devices controlling them. The
Longsheer L8150 gains touchscreen, sensors, vibrator and LED support.

MSM8992 gains USB and SDHCI support as well as an I2C controller and the
associated RMI4 based touchscreen for the Lumia 950.

MSM8994 also gains USB and SDHCI support, as well as VADC and temp-alarm
support. Then support for the Lumia 950 XL is added.

SDM845 gains interconnect properties for a number of devices and the
GENI wrappers gains iommu stream configuration, which means DMA
operations on e.g. I2C now works. The Lenovo Yoga C630 finally has the
SMMU enabled, a few fixes and the description of the eDP bridge and
panel means that the laptop can now boot mainline with working display,
GPU, WiFi and audio.

SC7180 gains a slew of smaller improvements and fixes.

* tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (93 commits)
arm64: dts: qcom: c630: Define eDP bridge and panel
arm64: dts: qcom: c630: Fix pinctrl pins properties
arm64: dts: qcom: c630: Polish i2c-hid devices
arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
arm64: dts: sdm845: Add interconnect properties for QUP
interconnect: qcom: sdm845: Add the missing nodes for QUP
dt-bindings: interconnect: sdm845: Add IDs for the QUP ports
arm64: dts: qcom: c630: Expose LID events
arm64: dts: qcom: c630: Re-enable apps_smmu
dts: qcom: sdm845: Add dt entries to support crypto engine.
arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD
arm64: dts: qcom: sdm845: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: limit IPA iommu streams
arm64: dts: qcom: sm8150: Add Coresight support
arm64: dts: qcom: sc7180-trogdor: Make pp3300_a the default supply for pp3300_hub
arm64: dts: qcom: sc7180: Add DDR/L3 votes for the pro variant
arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite
arm64: dts: qcom: sc7180-trogdor: add "pen-insert" label for trogdor
arm64: qcom: sc7180: trogdor: Add ADC nodes and thermal zone for charger thermistor
...

Link: https://lore.kernel.org/r/20201130190131.345187-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann

Merge tag 'icc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next

2020-12-04T13:11:20+00:00

Georgi writes:

interconnect changes for 5.11

Here are the interconnect changes for the 5.10-rc1 merge window
consisting of new driver and a cleanup.

Driver changes:
- New driver for Samsung Exynos SoCs
- Misc cleanups

Signed-off-by: Georgi Djakov 

* tag 'icc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
  MAINTAINERS: Add entry for Samsung interconnect drivers
  interconnect: Add generic interconnect driver for Exynos SoCs
  interconnect: qcom: Simplify the vcd compare function

interconnect: qcom: sdm845: Add the missing nodes for QUP

2020-11-30T16:42:47+00:00

The QUP nodes are currently defined just as entries in the topology,
but they are not referenced by any of the NoCs. Let's fix this and
"attach" them to their NoCs, so that the QUP drivers are able to use
them as path endpoints and scale their bandwidth.

This is based on the information from the downstream msm-4.9 kernel.

Reviewed-by: Bjorn Andersson 
Signed-off-by: Georgi Djakov 
Link: https://lore.kernel.org/r/20201105135211.7160-2-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson

interconnect: qcom: Simplify the vcd compare function

2020-11-30T15:26:22+00:00

Let's simplify the cmp_vcd() function and replace the conditionals
with just a single statement, which also improves readability.

Reviewed-by: Mike Tipton 
Link: https://lore.kernel.org/r/20201013171923.7351-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov

interconnect: qcom: qcs404: Remove GPU and display RPM IDs

2020-11-20T13:52:05+00:00

The following errors are noticed during boot on a QCS404 board:
[    2.926647] qcom_icc_rpm_smd_send mas 6 error -6
[    2.934573] qcom_icc_rpm_smd_send mas 8 error -6

These errors show when we try to configure the GPU and display nodes.
Since these particular nodes aren't supported on RPM and are purely
local, we should just change their mas_rpm_id to -1 to avoid any
requests being sent for these master IDs.

Reviewed-by: Mike Tipton 
Reviewed-by: Bjorn Andersson 
Link: https://lore.kernel.org/r/20201118111044.26056-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov

interconnect: qcom: msm8916: Remove rpm-ids from non-RPM nodes

2020-11-20T13:51:51+00:00

Some nodes are incorrectly marked as RPM-controlled (they have RPM
master and slave ids assigned), but are actually controlled by the
application CPU instead. The RPM complains when we send requests for
resources that it can't control. Let's fix this by replacing the IDs,
with the default "-1" in which case no requests are sent.

Reviewed-by: Mike Tipton 
Link: https://lore.kernel.org/r/20201112105140.10092-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov

interconnect: qcom: msm8974: Don't boost the NoC rate during boot

2020-11-17T22:21:47+00:00

It has been reported that on Fairphone 2 (msm8974-based), increasing
the clock rate for some of the NoCs during boot may lead to hangs.
Let's restore the original behavior and not touch the clock rate of
any of the NoCs to fix the regression.

Reported-by: Luca Weiss 
Tested-by: Luca Weiss 
Fixes: b1d681d8d324 ("interconnect: Add sync state support")
Link: https://lore.kernel.org/r/20201109124512.10776-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov

interconnect: qcom: msm8974: Prevent integer overflow in rate

2020-11-17T22:18:05+00:00

When sync_state support got introduced recently, by default we try to
set the NoCs to run initially at maximum rate. But as these values are
aggregated, we may end with a really big clock rate value, which is
then converted from "u64" to "long" during the clock rate rounding.
But on 32bit platforms this may result an overflow. Fix it by making
sure that the rate is within range.

Reported-by: Luca Weiss 
Reviewed-by: Brian Masney 
Link: https://lore.kernel.org/r/20201106144847.7726-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov