Add sub-driver for the LEDs on National Semiconductor / TI LM3533 lighting power chips. The chip provides 256 brightness levels, hardware accelerated blinking as well as ambient-light-sensor and pwm input control. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Rob Landley <rob@landley.net> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Bryan Wu <bryan.wu@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The leds timer trigger does not currently have an interface to activate a one shot timer. The current support allows for setting two timers, one for specifying how long a state to be on, and the second for how long the state to be off. The delay_on value specifies the time period an LED should stay in on state, followed by a delay_off value that specifies how long the LED should stay in off state. The on and off cycle repeats until the trigger gets deactivated. There is no provision for one time activation to implement features that require an on or off state to be held just once and then stay in the original state forever. Without one shot timer interface, user space can still use timer trigger to set a timer to hold a state, however when user space application crashes or goes away without deactivating the timer, the hardware will be left in that state permanently. As a specific example of this use-case, let's look at vibrate feature on phones. Vibrate function on phones is implemented using PWM pins on SoC or PMIC. There is a need to activate one shot timer to control the vibrate feature, to prevent user space crashes leaving the phone in vibrate mode permanently causing the battery to drain. This trigger exports three properties, activate, state, and duration When transient trigger is activated these properties are set to default values. - duration allows setting timer value in msecs. The initial value is 0. - activate allows activating and deactivating the timer specified by duration as needed. The initial and default value is 0. This will allow duration to be set after trigger activation. - state allows user to specify a transient state to be held for the specified duration. Signed-off-by: Shuah Khan <shuahkhan@gmail.com> Cc: Jonas Bonn <jonas@southpole.se> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: NeilBrown <neilb@suse.de> Cc: Bryan Wu <bryan.wu@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LED Driver for Dialog Semiconductor DA9052/53 PMICs. [akpm@linux-foundation.org: make led_reg static] Signed-off-by: David Dajun Chen <dchen@diasemi.com> Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Bryan Wu <bryan.wu@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson: "These changes are all specific to one board only. We're trying to keep the number of board files low, but generally board level updates are ok on platforms that are working on moving towards DT based probing, which will eventually lead to removing them. The board-ams-delta.c board file gets a conflict between the removal of ams_delta_config and the addition of a lot of other data. The Kconfig file has two changes in the same line, and in exynos, the power domain cleanup conflicts with the addition of the image sensor device. Signed-off-by: Arnd Bergmann <arnd@arndb.de> [olof: Amended a fix for a mismerge to board-omap4panda.c] Signed-off-by: Olof Johansson <olof@lixom.net>" Fixed up some fairly trivial conflicts manually. * tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits) i.MX35-PDK: Add Camera support ARM : mx35: 3ds-board: add framebuffer device pxa/hx4700: Remove pcmcia platform_device structure ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35% ARM: pxa/hx4700: Remove unwanted request for GPIO105 ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board ARM: EXYNOS: Register JPEG on nuri ARM: EXYNOS: Register JPEG on universal_c210 ARM: S5PV210: Enable JPEG on SMDKV210 ARM: S5PV210: Add JPEG board definition ARM: EXYNOS: Enable JPEG on Origen ARM: EXYNOS: Enable JPEG on SMDKV310 ARM: EXYNOS: Add __init attribute to universal_camera_init() ARM: EXYNOS: Add __init attribute to nuri_camera_init() ARM: S5PV210: Enable FIMC on SMDKC110 ARM: S5PV210: Enable FIMC on SMDKV210 ARM: S5PV210: Enable MFC on SMDKC110 ARM: S5PV210: Enable MFC on SMDKV210 ARM: EXYNOS: Enable G2D on SMDKV310 ARM: tegra: update defconfig ...
Driver for the PCA9633 I2C chip supporting four LEDs and 255 brightness levels. [akpm@linux-foundation.org: fix kcalloc() call] [axel.lin@gmail.com: fix kcalloc parameters swapped] Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com> Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add platform driver for the Soekris Engineering net5501 single-board computer. Probes well-known locations in ROM for BIOS signature to confirm correct platform. Registers 1 LED and 1 GPIO-based button (typically used for soft reset). Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Andres Salomon <dilinger@queued.net> Cc: Matthew Garrett <mjg@redhat.com> [ Removed Kconfig and Makefile detritus from drivers/leds/] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/n/tip-jv5uf34996juqh5syes8mn4h@git.kernel.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'omap1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: input: serio: ams-delta: toggle keyboard power over GPIO omapfb: lcd_ams_delta: drive control lines over GPIO MTD: NAND: ams-delta: use GPIO instead of custom I/O LED: drop leds-ams-delta driver ARM: OMAP1: ams-delta: supersede custom led device by leds-gpio ARM: OMAP1: ams-delta: convert latches to basic_mmio_gpio ARM: OMAP1: ams-delta: register latch dependent devices later
Add support for leds on Bachmann's ot200 visualisation device. The device has three leds on the back panel (led_err, led_init and led_run) and can handle up to seven leds on the front panel. The driver was written by Linutronix on behalf of Bachmann electronic GmbH. It incorporates feedback from Lars-Peter Clausen [akpm@linux-foundation.org: add dependency on HAS_IOMEM] Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts: drivers/leds/leds-ams-delta.c
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits) rtc: max8925: Add function to work as wakeup source mfd: Add pm ops to max8925 mfd: Convert aat2870 to dev_pm_ops mfd: Still check other interrupts if we get a wm831x touchscreen IRQ mfd: Introduce missing kfree in 88pm860x probe routine mfd: Add S5M series configuration mfd: Add s5m series irq driver mfd: Add S5M core driver mfd: Improve mc13xxx dt binding document mfd: Fix stmpe section mismatch mfd: Fix stmpe build warning mfd: Fix STMPE I2c build failure mfd: Constify aat2870-core i2c_device_id table gpio: Add support for stmpe variant 801 mfd: Add support for stmpe variant 801 mfd: Add support for stmpe variant 610 mfd: Add support for STMPE SPI interface mfd: Separate out STMPE controller and interface specific code misc: Remove max8997-muic sysfs attributes mfd: Remove unused wm831x_irq_data_to_mask_reg() ... Fix up trivial conflict in drivers/leds/Kconfig due to addition of LEDS_MAX8997 and LEDS_TCA6507 next to each other.