linux-toradex.git/drivers/leds, branch v3.12.45

leds / PM: fix hibernation on arm when gpio-led used with CPU led trigger

2015-07-30T12:10:51+00:00

commit 084609bf727981c7a2e6e69aefe0052c9d793300 upstream.

Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of
hibernation callbacks means those pm functions will not be
called upon hibernation - that leads to system crash on ARM during
freezing if gpio-led is used in combination with CPU led trigger.
It may happen after freeze_noirq stage (GPIO is suspended)
and before syscore_suspend stage (CPU led trigger is suspended)
- usually when disable_nonboot_cpus() is called.

Log:
  PM: noirq freeze of devices complete after 1.425 msecs
  Disabling non-boot CPUs ...
    ^ system may crash or stuck here with message (TI AM572x)

  WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370()
  44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access

  CPU1: shutdown
    ^ or here

Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation callbacks and move
led_suspend/led_resume under CONFIG_PM_SLEEP to avoid
build warnings.

Fixes: 73e1ab41a80d (leds: Convert led class driver from legacy pm ops to dev_pm_ops)
Signed-off-by: Grygorii Strashko 
Acked-by: Jacek Anaszewski 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Jiri Slaby

leds: leds-pwm: properly clean up after probe failure

2014-06-09T13:53:22+00:00

commit 392369019eb96e914234ea21eda806cb51a1073e upstream.

When probing with DT, we add each LED one at a time.  If we find a LED
without a PWM device (because it is not available yet) we fail the
initialisation, unregister previous LEDs, and then by way of managed
resources, we free the structure.

The problem with this is we may have a scheduled and active work_struct
in this structure, and this results in a nasty kernel oops.

We need to cancel this work_struct properly upon cleanup - and the
cleanup we require is the same cleanup as we do when the LED platform
device is removed.  Rather than writing this same code three times,
move it into a separate function and use it in all three places.

Fixes: c971ff185f64 ("leds: leds-pwm: Defer led_pwm_set() if PWM can sleep")
Signed-off-by: Russell King 
Signed-off-by: Bryan Wu 
Signed-off-by: Jiri Slaby

leds: lp5521/5523: Remove duplicate mutex

2014-01-15T23:31:42+00:00

commit e70988d1aaf73221355e06125c9937bd4b27761c upstream.

It can be a problem when a pattern is loaded via the firmware interface.
LP55xx common driver has already locked the mutex in 'lp55xx_firmware_loaded()'.
So it should be deleted.

On the other hand, locks are required in store_engine_load()
on updating program memory.

Reported-by: Pali Rohár 
Reported-by: Pavel Machek 
Signed-off-by: Milo Kim 
Signed-off-by: Bryan Wu 
Signed-off-by: Greg Kroah-Hartman

Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds

2013-09-12T18:35:33+00:00

Pull led updates from Bryan Wu:
 "Sorry for the late pull request, since I'm just back from vacation.

  LED subsystem updates for 3.12:
   - pca9633 driver DT supporting and pca9634 chip supporting
   - restore legacy device attributes for lp5521
   - other fixing and updates"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (28 commits)
  leds: wm831x-status: Request a REG resource
  leds: trigger: ledtrig-backlight: Fix invalid memory access in fb_event notification callback
  leds-pca963x: Fix device tree parsing
  leds-pca9633: Rename to leds-pca963x
  leds-pca9633: Add mutex to the ledout register
  leds-pca9633: Unique naming of the LEDs
  leds-pca9633: Add support for PCA9634
  leds: lp5562: use LP55xx common macros for device attributes
  Documentation: leds-lp5521,lp5523: update device attribute information
  leds: lp5523: remove unnecessary writing commands
  leds: lp5523: restore legacy device attributes
  leds: lp5523: LED MUX configuration on initializing
  leds: lp5523: make separate API for loading engine
  leds: lp5521: remove unnecessary writing commands
  leds: lp5521: restore legacy device attributes
  leds: lp55xx: add common macros for device attributes
  leds: lp55xx: add common data structure for program
  Documentation: leds: Fix a typo
  leds: ss4200: Fix incorrect placement of __initdata
  leds: clevo-mail: Fix incorrect placement of __initdata
  ...

Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2013-09-06T20:34:43+00:00

Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.

- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"

* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...

leds: wm831x-status: Request a REG resource

2013-08-30T17:17:45+00:00

The wm831x-status driver was not converted to use a REG resource when they
were introduced and the rest of the wm831x drivers converted, causing it
to fail to probe due to requesting the wrong resource type.

Signed-off-by: Mark Brown 
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Bryan Wu

leds: trigger: ledtrig-backlight: Fix invalid memory access in fb_event notification callback

2013-08-27T00:46:36+00:00

fb_notifier_callback is called on any event fired by
fb_notifier_call_chain. Events may, or may not contain some data
(fb_event.data). In case of FB_EVENT_BLANK fb_event.data contains a
pointer to an integer holdingthe blank state. The Problem is, that in
ledtrig-backlight.c - fb_notifier_callback the pointer to blank state
is dereferenced BEFORE the event-type is checked.

Obviously this leads to problems with other events than FB_EVENT_BLANK,
where fb_event.data is undefined or NULL. It seems, that this problem
existed ever since the driver was added.

Like in drivers/video/backlight/backlight.c line 43 I would suggest to
return immediately on events other than FB_EVENT_BLANK.

Signed-off-by: Manfred Schlaegl 
Signed-off-by: Bryan Wu

leds-pca963x: Fix device tree parsing

2013-08-27T00:22:14+00:00

A malformed device tree could lead into a segmentation fault if the reg
value of a led is bigger than the number of leds.

A valid device tree could have only information about the last led of the
chip. Fix the device tree parsing to handle those cases.

Signed-off-by: Ricardo Ribalda Delgado 
Signed-off-by: Bryan Wu

leds-pca9633: Rename to leds-pca963x

2013-08-27T00:22:14+00:00

The driver now supports the chips pca9633 and pca9634, therefore we
rename the files to more generic and meaningul names

Signed-off-by: Ricardo Ribalda Delgado 
Signed-off-by: Bryan Wu

leds-pca9633: Add mutex to the ledout register

2013-08-27T00:22:14+00:00

To update an LED a register has to be read, updated and writen. If
another LED whas been updated at the same time, this could lead into
wrong updates.

This patch adds a common mutex to all the leds of the same chip to
protect the ledout register.

Signed-off-by: Ricardo Ribalda Delgado 
Signed-off-by: Bryan Wu