This option is not well justified and testing suggests that
it hardly ever makes any difference.

The comment suggests there might be a need to wait for non-resync
activity indicated by ->nr_waiting, however raise_barrier()
already waits for all of that.

So just remove it to simplify reasoning about speed limiting.

This allows us to remove a 'FIXME' comment from raid5.c as that
never used the flag.

Signed-off-by: NeilBrown <neilb@suse.de>

This is required by the clustering module (patches to follow) to
find the device to remove or re-add.

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>

This export is required for clustering module in order to
co-ordinate remove/readd a rdev from all nodes.

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>

Algorithm:
1. Node 1 issues mdadm --manage /dev/mdX --add /dev/sdYY which issues
   ioctl(ADD_NEW_DISC with disc.state set to MD_DISK_CLUSTER_ADD)
2. Node 1 sends NEWDISK with uuid and slot number
3. Other nodes issue kobject_uevent_env with uuid and slot number
(Steps 4,5 could be a udev rule)
4. In userspace, the node searches for the disk, perhaps
   using blkid -t SUB_UUID=""
5. Other nodes issue either of the following depending on whether the disk
   was found:
   ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CANDIDATE and
	 disc.number set to slot number)
   ioctl(CLUSTERED_DISK_NACK)
6. Other nodes drop lock on no-new-devs (CR) if device is found
7. Node 1 attempts EX lock on no-new-devs
8. If node 1 gets the lock, it sends METADATA_UPDATED after unmarking the disk
   as SpareLocal
9. If not (get no-new-dev lock), it fails the operation and sends METADATA_UPDATED
10. Other nodes understand if the device is added or not by reading the superblock again after receiving the METADATA_UPDATED message.

Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>

Re-reads the devices by invalidating the cache.
Since we don't write to faulty devices, this is detected using
events recorded in the devices. If it is old as compared to the mddev
mark it is faulty.

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>

DLM offers callbacks when a node fails and the lock remastery
is performed:

1. recover_prep: called when DLM discovers a node is down
2. recover_slot: called when DLM identifies the node and recovery
		can start
3. recover_done: called when all nodes have completed recover_slot

recover_slot() and recover_done() are also called when the node joins
initially in order to inform the node with its slot number. These slot
numbers start from one, so we deduct one to make it start with zero
which the cluster-md code uses.

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>

md_cluster_info stores the cluster information in the MD device.

The join() is called when mddev detects it is a clustered device.
The main responsibilities are:
	1. Setup a DLM lockspace
	2. Setup all initial locks such as super block locks and bitmap lock (will come later)

The leave() clears up the lockspace and all the locks held.

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>

This allows dynamic registering of cluster hooks.

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>

After each call to rdev_dec_pending() we should wakeup the
md thread if the device is found to be faulty.
Otherwise we'll incur heavy delays on failing devices.

Signed-off-by: Neil Brown <nfbrown@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>

The one which is not inline (mddev_unlock) gets EXPORTed.

This makes the locking available to personality modules so that it
doesn't have to be imposed upon them.

Signed-off-by: NeilBrown <neilb@suse.de>