commit 3056e3aec8d8ba61a0710fb78b2d562600aa2ea7 upstream.
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
[bwh: Backported to 3.2: for raid10, s/rdev/conf->mirrors[dev].rdev/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b7219ccb33aa0df9949a60c68b5e9f712615e56f upstream. If a resync of a RAID1 array with 2 devices finds a known bad block one device it will neither read from, or write to, that device for this block offset. So there will be one read_target (The other device) and zero write targets. This condition causes md/raid1 to abort the resync assuming that it has finished - without known bad blocks this would be true. When there are no write targets because of the presence of bad blocks we should only skip over the area covered by the bad block. RAID10 already gets this right, raid1 doesn't. Or didn't. As this can cause a 'sync' to abort early and appear to have succeeded it could lead to some data corruption, so it suitable for -stable. Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 58e94ae18478c08229626daece2fc108a4a23261 upstream.
commit 4367af556133723d0f443e14ca8170d9447317cb
md/raid1: clear bad-block record when write succeeds.
Added a 'reschedule_retry' call possibility at the end of
end_sync_write, but didn't add matching code at the end of
sync_request_write. So if the writes complete very quickly, or
scheduling makes it seem that way, then we can miss rescheduling
the request and the resync could hang.
Also commit 73d5c38a9536142e062c35997b044e89166e063b
md: avoid races when stopping resync.
Fix a race condition in this same code in end_sync_write but didn't
make the change in sync_request_write.
This patch updates sync_request_write to fix both of those.
Patch is suitable for 3.1 and later kernels.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Original-version-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2d4f4f3384d4ef4f7c571448e803a1ce721113d5 upstream. This bug has been present ever since data-check was introduce in 2.6.16. However it would only fire if a data-check were done on a degraded array, which was only possible if the array has 3 or more devices. This is certainly possible, but is quite uncommon. Since hot-replace was added in 3.3 it can happen more often as the same condition can arise if not all possible replacements are present. The problem is that as soon as we submit the last read request, the 'r1_bio' structure could be freed at any time, so we really should stop looking at it. If the last device is being read from we will stop looking at it. However if the last device is not due to be read from, we will still check the bio pointer in the r1_bio, but the r1_bio might already be free. So use the read_targets counter to make sure we stop looking for bios to submit as soon as we have submitted them all. This fix is suitable for any -stable kernel since 2.6.16. Reported-by: Arnold Schulz <arnysch@gmx.net> Signed-off-by: NeilBrown <neilb@suse.de> [bwh: Backported to 3.2: no doubling of conf->raid_disks; we don't have hot-replace support] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d6b42dcb995e6acd7cc276774e751ffc9f0ef4bf upstream. If RAID1 or RAID10 is used under LVM or some other stacking block device, it is possible to enter a deadlock during resync or recovery. This can happen if the upper level block device creates two requests to the RAID1 or RAID10. The first request gets processed, blocks recovery and queue requests for underlying requests in current->bio_list. A resync request then starts which will wait for those requests and block new IO. But then the second request to the RAID1/10 will be attempted and it cannot progress until the resync request completes, which cannot progress until the underlying device requests complete, which are on a queue behind that second request. So allow that second request to proceed even though there is a resync request about to start. This is suitable for any -stable kernel. Reported-by: Ray Morris <support@bettercgi.com> Tested-by: Ray Morris <support@bettercgi.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 307729c8bc5b5a41361af8af95906eee7552acb1 upstream. We normally try to avoid reading from write-mostly devices, but when we do we really have to check for bad blocks and be sure not to try reading them. With the current code, best_good_sectors might not get set and that causes zero-length read requests to be send down which is very confusing. This bug was introduced in commit d2eb35acfdccbe2 and so the patch is suitable for 3.1.x and 3.2.x Reported-and-tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reported-and-tested-by: Art -kwaak- van Breemen <ard@telegraafnet.nl> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
A pending cleanup will mean that module.h won't be implicitly everywhere anymore. Make sure the modular drivers in md dir are actually calling out for <module.h> explicitly in advance. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In 3.0 we changed the way recovery_disabled was handle so that instead
of testing against zero, we test an mddev-> value against a conf->
value.
Two problems:
1/ one place in raid1 was missed and still sets to '1'.
2/ We didn't explicitly set the conf-> value at array creation
time.
It defaulted to '0' just like the mddev value does so they
could appear equal and thus disable recovery.
This did not affect normal 'md' as it calls bind_rdev_to_array
which changes the mddev value. However the dmraid interface
doesn't call this and so doesn't change ->recovery_disabled; so at
array start all recovery is incorrectly disabled.
So initialise the 'conf' value to one less that the mddev value, so
the will only be the same when explicitly set that way.
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>