A recent patch to raid5.c use min on an int and a sector_t.
This isn't allowed.
So change it to min_t(sector_t,x,y).

Signed-off-by: NeilBrown <neilb@suse.de>

md has no need for the BKL - it does its own locking.
So md_ioctl doesn't need to be a locked_ioctl.

Signed-off-by: NeilBrown <neilb@suse.de>

In order for the metadata to always be consistent, we mustn't updated
curr_resync_completed without also updating reshape_position.

The reshape code updates both at the same time.  However since
commit 97e4f42d62badb0f9fbc27c013e89bc1336a03bc
the common md_do_sync will sometimes update curr_resync_completed
but is not in a position to update reshape_position.
So if MD_RECOVERY_RESHAPE is set (indicating that a reshape is
happening, so reshape_position might change), don't update
curr_resync_completed in md_do_sync, leave it to the per-personality
reshape code.

Signed-off-by: NeilBrown <neilb@suse.de>

As sector_t in unsigned, we cannot afford to let 'safepos' etc go
negative.
So replace
   a -= b;
by
   a -= min(b,a);

Signed-off-by: NeilBrown <neilb@suse.de>

The md resync engine has a 'frozen' state which ensures that
no resync/recovery.  This is used to avoid races.

Export this state through the 'sync_action' sysfs attribute
so that user-space can benefit and also avoid some races.

Signed-off-by: NeilBrown <neilb@suse.de>

The code for checking which bits in the bitmap can be cleared
has 2 problems:
 1/ it repeatedly takes and drops a spinlock, where it would make
    more sense to just hold on to it most of the time.
 2/ it doesn't make use of some opportunities to skip large sections
    of the bitmap

This patch fixes those.  It will only affect CPU consumption, not
correctness.

Signed-off-by: NeilBrown <neilb@suse.de>

Instead of always returns EINVAL if anything goes wrong
when setting the array size, add the option of
  E2BIG
if the size requested is too large.  This makes it easier
for user-space to be sure what went wrong.

Signed-off-by: NeilBrown <neilb@suse.de>

We previously didn't update these fields when writing the metadata
because they could never change.  They can now, so we better write
them.
v0.90 metadata always updated these fields.

Signed-off-by: NeilBrown <neilb@suse.de>

md maintains link in sys/mdXX/md/ to identify which device has
which role in the array. e.g.
   rd2 -> dev-sda

indicates that the device with role '2' in the array is sda.

These links are only present when the array is active.  They are
created immediately after ->run is called, and so should be removed
immediately after ->stop is called.
However they are currently removed a little bit later, and it is
possible for ->run to be called again, thus adding these links, before
they are removed.

So move the removal earlier so they are consistently only present when
the array is active.

Signed-off-by: NeilBrown <neilb@suse.de>

Being able to write 'clean' to an 'array_state' of an inactive array
to activate it in 'clean' mode is both unnecessary and inconvenient.

It is unnecessary because the same can be achieved by writing
'active'.  This activates and array, but it still remains 'clean'
until the first write.

It is inconvenient because writing 'clean' is more often used to
cause an 'active' array to revert to 'clean' mode (thus blocking
any writes until a 'write-pending' is promoted to 'active').

Allowing 'clean' to both activate an array and mark an active array as
clean can lead to races:  One program writes 'clean' to mark the
active array as clean at the same time as another program writes
'inactive' to deactivate (stop) and active array.  Depending on which
writes first, the array could be deactivated and immediately
reactivated which isn't what was desired.

So just disable the use of 'clean' to activate an array.

This avoids a race that can be triggered with mdadm-3.0 and external
metadata, so it suitable for -stable.

Reported-by: Rafal Marszewski <rafal.marszewski@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>