linux-toradex.git/drivers/md, branch v3.10.9

dm verity: fix inability to use a few specific devices sizes

2013-08-04T08:51:02+00:00

commit b1bf2de07271932326af847a3c6a01fdfd29d4be upstream.

Fix a boundary condition that caused failure for certain device sizes.

The problem is reported at
  http://code.google.com/p/cryptsetup/issues/detail?id=160

For certain device sizes the number of hashes at a specific level was
calculated incorrectly.

It happens for example for a device with data and metadata block size 4096
that has 16385 blocks and algorithm sha256.

The user can test if he is affected by this bug by running the
"veritysetup verify" command and also by activating the dm-verity kernel
driver and reading the whole block device. If it passes without an error,
then the user is not affected.

The condition for the bug is:

Split the total number of data blocks (data_block_bits) into bit strings,
each string has hash_per_block_bits bits. hash_per_block_bits is
rounddown(log2(metadata_block_size/hash_digest_size)). Equivalently, you
can say that you convert data_blocks_bits to 2^hash_per_block_bits base.

If there some zero bit string below the most significant bit string and at
least one bit below this zero bit string is set, then the bug happens.

The same bug exists in the userspace veritysetup tool, so you must use
fixed veritysetup too if you want to use devices that are affected by
this boundary condition.

Signed-off-by: Mikulas Patocka 
Cc: Milan Broz 
Signed-off-by: Alasdair G Kergon 
Signed-off-by: Greg Kroah-Hartman

dm ioctl: set noio flag to avoid __vmalloc deadlock

2013-08-04T08:51:02+00:00

commit 1c0e883e86ece31880fac2f84b260545d66a39e0 upstream.

Set noio flag while calling __vmalloc() because it doesn't fully respect
gfp flags to avoid a possible deadlock (see commit
502624bdad3dba45dfaacaf36b7d83e39e74b2d2).

This should be backported to stable kernels 3.8 and newer. The kernel 3.8
doesn't have memalloc_noio_save(), so we should set and restore process
flag PF_MEMALLOC instead.

Signed-off-by: Mikulas Patocka 
Signed-off-by: Alasdair G Kergon 
Signed-off-by: Greg Kroah-Hartman

dm mpath: fix ioctl deadlock when no paths

2013-08-04T08:51:02+00:00

commit 6c182cd88d179cbbd06f4f8a8a19b6977940753f upstream.

When multipath needs to retry an ioctl the reference to the
current live table needs to be dropped. Otherwise a deadlock
occurs when all paths are down:
- dm_blk_ioctl takes a reference to the current table
  and spins in multipath_ioctl().
- A new table is being loaded, but upon resume the process
  hangs in dm_table_destroy() waiting for references to
  drop to zero.

With this patch the reference to the old table is dropped
prior to retry, thereby avoiding the deadlock.

Signed-off-by: Hannes Reinecke 
Cc: Mike Snitzer 
Signed-off-by: Alasdair G Kergon 
Signed-off-by: Greg Kroah-Hartman

md/raid10: remove use-after-free bug.

2013-08-04T08:50:55+00:00

commit 0eb25bb027a100f5a9df8991f2f628e7d851bc1e upstream.

We always need to be careful when calling generic_make_request, as it
can start a chain of events which might free something that we are
using.

Here is one place I wasn't careful enough.  If the wbio2 is not in
use, then it might get freed at the first generic_make_request call.
So perform all necessary tests first.

This bug was introduced in 3.3-rc3 (24afd80d99) and can cause an
oops, so fix is suitable for any -stable since then.

Signed-off-by: NeilBrown 
Signed-off-by: Greg Kroah-Hartman

md/raid5: fix interaction of 'replace' and 'recovery'.

2013-08-04T08:50:54+00:00

commit f94c0b6658c7edea8bc19d13be321e3860a3fa54 upstream.

If a device in a RAID4/5/6 is being replaced while another is being
recovered, then the writes to the replacement device currently don't
happen, resulting in corruption when the replacement completes and the
new drive takes over.

This is because the replacement writes are only triggered when
's.replacing' is set and not when the similar 's.sync' is set (which
is the case during resync and recovery - it means all devices need to
be read).

So schedule those writes when s.replacing is set as well.

In this case we cannot use "STRIPE_INSYNC" to record that the
replacement has happened as that is needed for recording that any
parity calculation is complete.  So introduce STRIPE_REPLACED to
record if the replacement has happened.

For safety we should also check that STRIPE_COMPUTE_RUN is not set.
This has a similar effect to the "s.locked == 0" test.  The latter
ensure that now IO has been flagged but not started.  The former
checks if any parity calculation has been flagged by not started.
We must wait for both of these to complete before triggering the
'replace'.

Add a similar test to the subsequent check for "are we finished yet".
This possibly isn't needed (is subsumed in the STRIPE_INSYNC test),
but it makes it more obvious that the REPLACE will happen before we
think we are finished.

Finally if a NeedReplace device is not UPTODATE then that is an
error.  We really must trigger a warning.

This bug was introduced in commit 9a3e1101b827a59ac9036a672f5fa8d5279d0fe2
(md/raid5:  detect and handle replacements during recovery.)
which introduced replacement for raid5.
That was in 3.3-rc3, so any stable kernel since then would benefit
from this fix.

Reported-by: qindehua <13691222965@163.com>
Tested-by: qindehua 
Signed-off-by: NeilBrown 
Signed-off-by: Greg Kroah-Hartman

md/raid1: fix bio handling problems in process_checks()

2013-08-04T08:50:54+00:00

commit 30bc9b53878a9921b02e3b5bc4283ac1c6de102a upstream.

Recent change to use bio_copy_data() in raid1 when repairing
an array is faulty.

The underlying may have changed the bio in various ways using
bio_advance and these need to be undone not just for the 'sbio' which
is being copied to, but also the 'pbio' (primary) which is being
copied from.

So perform the reset on all bios that were read from and do it early.

This also ensure that the sbio->bi_io_vec[j].bv_len passed to
memcmp is correct.

This fixes a crash during a 'check' of a RAID1 array.  The crash was
introduced in 3.10 so this is suitable for 3.10-stable.

Reported-by: Joe Lawrence 
Signed-off-by: NeilBrown 
Signed-off-by: Greg Kroah-Hartman

md: Remove recent change which allows devices to skip recovery.

2013-08-04T08:50:53+00:00

commit 5024c298311f3b97c85cb034f9edaa333fdb9338 upstream.

commit 7ceb17e87bde79d285a8b988cfed9eaeebe60b86
    md: Allow devices to be re-added to a read-only array.

allowed a bit more than just that.  It also allows devices to be added
to a read-write array and to end up skipping recovery.

This patch removes the offending piece of code pending a rewrite for a
subsequent release.

More specifically:
 If the array has a bitmap, then the device will still need a bitmap
 based resync ('saved_raid_disk' is set under different conditions
 is a bitmap is present).
 If the array doesn't have a bitmap, then this is correct as long as
 nothing has been written to the array since the metadata was checked
 by ->validate_super.  However there is no locking to ensure that there
 was no write.

Bug was introduced in 3.10 and causes data corruption so
patch is suitable for 3.10-stable.

Reported-by: Joe Lawrence 
Signed-off-by: NeilBrown 
Signed-off-by: Greg Kroah-Hartman

bcache: Journal replay fix

2013-07-28T23:30:10+00:00

commit faa5673617656ee58369a3cfe4a312cfcdc59c81 upstream.

The journal replay code starts by finding something that looks like a
valid journal entry, then it does a binary search over the unchecked
region of the journal for the journal entries with the highest sequence
numbers.

Trouble is, the logic was wrong - journal_read_bucket() returns true if
it found journal entries we need, but if the range of journal entries
we're looking for loops around the end of the journal - in that case
journal_read_bucket() could return true when it hadn't found the highest
sequence number we'd seen yet, and in that case the binary search did
the wrong thing. Whoops.

Signed-off-by: Kent Overstreet 
Signed-off-by: Greg Kroah-Hartman

bcache: Fix GC_SECTORS_USED() calculation

2013-07-28T23:30:10+00:00

commit 29ebf465b9050f241c4433a796a32e6c896a9dcd upstream.

Part of the job of garbage collection is to add up however many sectors
of live data it finds in each bucket, but that doesn't work very well if
it doesn't reset GC_SECTORS_USED() when it starts. Whoops.

This wouldn't have broken anything horribly, but allocation tries to
preferentially reclaim buckets that are mostly empty and that's not
gonna work with an incorrect GC_SECTORS_USED() value.

Signed-off-by: Kent Overstreet 
Signed-off-by: Greg Kroah-Hartman

bcache: Fix a sysfs splat on shutdown

2013-07-28T23:30:10+00:00

commit c9502ea4424b31728703d113fc6b30bfead14633 upstream.

If we stopped a bcache device when we were already detaching (or
something like that), bcache_device_unlink() would try to remove a
symlink from sysfs that was already gone because the bcache dev kobject
had already been removed from sysfs.

So keep track of whether we've removed stuff from sysfs.

Signed-off-by: Kent Overstreet 
Signed-off-by: Greg Kroah-Hartman