dvb_usb_device_init calls the frontend_attach method of this driver which
uses vp7045_usb_ob. In order to have a buffer ready in vp7045_usb_op, it has to
be allocated before that happens.

Luckily we can use the whole private data as the buffer as it gets separately
allocated on the heap via kzalloc in dvb_usb_device_init and is thus apt for
use via usb_control_msg.

This fixes a
	BUG: unable to handle kernel paging request at 0000000000001e78

reported by Tino Keitel and diagnosed by Dan Carpenter.

Cc: stable@kernel.org # For v3.0 and upper
Tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
  [media] ir-mce_kbd-decoder: include module.h for its facilities
  [media] ov5642: include module.h for its facilities
  [media] em28xx: Fix DVB-C maxsize for em2884
  [media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
  [media] v4l: mt9v032: Fix Bayer pattern
  [media] V4L: mt9m111: rewrite set_pixfmt
  [media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
  [media] V4L: initial driver for ov5642 CMOS sensor
  [media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
  [media] V4L: soc-camera: remove soc-camera bus and devices on it
  [media] V4L: soc-camera: un-export the soc-camera bus
  [media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
  [media] V4L: add media bus configuration subdev operations
  [media] V4L: soc-camera: group struct field initialisations together
  [media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
  [media] V4L: pxa-camera: switch to using standard PM hooks
  [media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
  [media] Don't OOPS if videobuf_dvb_get_frontend return NULL
  [media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
  [media] omap3isp: Support configurable HS/VS polarities
  ...

Fix up conflicts:
 - arch/arm/mach-omap2/board-rx51-peripherals.c:
     cleanup regulator supply definitions in mach-omap2
   vs
     OMAP3: RX-51: define vdds_csib regulator supply
 - drivers/staging/tm6000/tm6000-alsa.c (trivial)

Currently, the driver assumes that all QAM carriers are spaced with
8MHz. This is wrong, and may decrease QoS on Countries like Brazil,
that have DVB-C carriers with 6MHz-spaced.

Fortunately, both ITU-T J-83 and EN 300 429 specifies a way to
associate the symbol rate with the bandwidth needed for it.

For ITU-T J-83 2007 annex A, the maximum symbol rate for 6 MHz is:
	6 MHz / 1.15 = 5217391 Bauds
For  ITU-T J-83 2007 annex C, the maximum symbol rate for 6 MHz is:
	6 MHz / 1.13 = 5309735 Bauds.

As this tuner is currently used only for DRX-K, and it is currently
hard-coded to annex A, I've opted to use the roll-off factor of 0.15,
instead of 0.13.

If we ever support annex C, the better would be to add a DVB S2API
call to allow changing between Annex A and C, and add the 0.13 roll-off
factor to it.

This code is currently being used on other frontends, so I think we
should later add a core function with this code, to warrant that
it will be properly implemented everywhere.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The signal state field in G_TUNER is typically scaled from 0-100%.  Since we
don't know the signal level, we really would prefer the field to contain 100%
than 1/256, which in many utilities (such as v4l2-ctl) rounds to 0% even when
a signal is actually present.

This patch makes the behavior consistent with other drivers.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Fix the DRX-K logic that selects between DVB-C annex A and C

Fix a typo where DVB-C annex type is set via setEnvParameters, but
the driver, uses, instead, setParamParameters[2].

While here, cleans up the code, fixing a bad identation at the fallback
code for other types of firmware, and put the multiple-line comments
into the Linux CodingStyle.

Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

After return, we don't need any other statement to change the
function flux ;)

Reported-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The error propagation changeset c23bf4402 broke the DVB-T
code.

The legacy way for propagate errors was:

do {
	status = foo_func()
	if (status < 0)
		break;
} while (0);
return status;

However, on a few places, it was doing:
do {
	switch(foo) {
	case bar:
		status = foo_func()
		if (status < 0)
			break;
		break;
	}
	switch(foo2) {
	case bar:
		status = foo_func()
		if (status < 0)
			break;
		break;
	}
	...
} while (0);
return (status)

The inner error break were not working, as it were breaking only
the switch, instead of the do. The solution used were to do a
s/break/goto error/ at the inner breaks, but preserving the last
break. Onfortunately, on a few switches, the replacement were
applied also to the final break for the case statements.

Fix the broken logic, by reverting them to break, where pertinent,
in order to fix DVB-T support.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Both ngene and ddbrige calls dvb_attach once for drxk_attach.
The logic used there, and by tda18271c2dd driver is different
from similar logic on other frontends.

The right fix is to change them to use the same logic, but,
while we don't do that, we need to patch em28xx-dvb in order
to do cope with ngene/ddbridge magic.

While here, document why drxk_t_release should do nothing.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>