Add driver for Intel Computer Vision Sensing (CVS) devices found on
Intel Luna Lake (LNL), Panther Lake (PTL), and Arrow Lake (ARL)
platforms.

The CVS device acts as a V4L2 sub-device bridge that manages CSI-2
link ownership between the host (Linux) and firmware for camera
sensors. It provides:

- Query the device status via sysfs interface
- CSI-2 link ownership arbitration between host and CVS firmware
- MIPI CSI-2 configuration management
- Privacy LED control coordination
- Power management integration with runtime PM

The driver consists of two main components:
  core.c: Core driver with probe, command transport, and power management
  v4l2.c: V4L2 sub-device and media framework integration

Hardware Interface:
- I2C for command/control communication with device firmware
- GPIO signals for ownership handshaking (request/response)
- Optional reset and wake interrupt for full-capability variants
- Integration with Intel IPU via ipu_bridge

The driver supports two hardware capability levels:
- Light capability: Basic GPIO-based ownership (2 GPIOs)
- Full capability: Enhanced with reset control and wake IRQ (4 GPIOs)

Device-specific quirks are handled via a quirk table to accommodate
variations across different CVS implementations (Lattice, Synaptics).

In addition to I2C-based operation, the driver supports platform
device instantiation for systems where CVS is exposed without I2C
transport, falling back to GPIO-only ownership control.

The CVS driver integrates with the IPU bridge for automatic device
discovery via ACPI on supported platforms.

PCI device IDs for Intel IPU7 (0x645d, shared by MTL and LNL) and
IPU7.5 (0xb05d, shared by ARL and PTL) are included in the
driver-local icvs_pci_tbl lookup table, enabling CVS to locate these
IPU variants without modifying the shared ipu6-pci-table header.

A PM runtime device link is established between IPU (consumer) and CVS
(supplier) so that the PM framework automatically resumes CVS before
IPU begins streaming, triggering cvs_runtime_resume() to claim CSI-2
link ownership. Ownership is released via cvs_runtime_suspend() after
the autosuspend delay.

Signed-off-by: Miguel Vadillo <miguel.vadillo@intel.com>
Tested-by: Mehdi Djait <mehdi.djait@linux.intel.com> # Dell XPS 13 9350 + IPU7
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Add the t4ka3 driver from:
https://github.com/kitakar5525/surface3-atomisp-cameras.git

With many cleanups / changes (almost a full rewrite) to make it suitable
for upstream:

* Remove the VCM and VCM-OTP support, the mainline kernel models VCMs and
  calibration data eeproms as separate v4l2-subdev-s.

* Remove the integration-factor t4ka3_get_intg_factor() support and IOCTL,
  this provided info to userspace through an atomisp private IOCTL.

* Turn atomisp specific exposure/gain IOCTL into standard v4l2 controls.

* Use normal ACPI power-management in combination with runtime-pm support
  instead of atomisp specific GMIN power-management code.

* Turn into a standard V4L2 sensor driver using
  v4l2_async_register_subdev_sensor().

* Add vblank, hblank, and link-freq controls; drop get_frame_interval().

* Use CCI register helpers.

* Calculate values for modes instead of using fixed register-value lists,
  allowing arbritrary modes.

* Add get_selection() and set_selection() support

* Add a CSI2 bus configuration check

This was tested on a Xiaomi Mipad2 tablet which has a T4KA3 sensor with
DW9761 VCM as back sensor.

Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Co-developed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>

Add a V4L2 subdevice driver for the Omnivision OV2732 sensor.

The OV2732 is a 1/4" color CMOS 1080p (1920x1080) HD image sensor with
programmable controls like: gain, exposure, frame rate, image and windowing
size, horizontal mirror, vertical flip, cropping.

Signed-off-by: Walter Werner Schneider <contact@schnwalter.eu>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
[Sakari Ailus: Squashed Walter's fixup.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>

Add a v4l2 subdevice driver for the Omnivision OS05B10 sensor.

The Omnivision OS05B10 image sensor with an active
array size of 2592 x 1944.

The following features are supported:
- Manual exposure an gain control support
- vblank/hblank control support
- Supported resolution: 2592 x 1944 @ 60fps (SBGGR10)

Co-developed-by: Elgin Perumbilly <elgin.perumbilly@siliconsignals.io>
Signed-off-by: Elgin Perumbilly <elgin.perumbilly@siliconsignals.io>
Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>

Samsung S5K3M5 (ISOCELL 3M5) is a 13MP image sensor, it produces
Bayer GRBG (2x2) frames in RAW10 output format, the maximum supported
output resolution is 4208x3120 at 30 frames per second.

Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>

Samsung S5KJN1 is a 50MP image sensor, it produces Bayer GRBG (2x2)
frames in RAW10 output format, the maximum supported output resolution
is 8160x6144 at 10 frames per second.

Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>

Add a v4l2 sub-device driver for the Sony IMX111 image sensor. This is a
camera sensor using the i2c bus for control and the csi-2 bus for data.

The following features are supported:
- manual exposure, digital and analog gain control support
- pixel rate/link freq control support
- supported resolution up to 3280x2464 for single shot capture
- supported resolution up to 1920x1080 @ 30fps for video
- supported bayer order output SGBRG10 and SGBRG8

Camera module seems to be partially compatible with Nokia SMIA but it
lacks a few registers required for clock calculations and has different
vendor-specific per-mode configurations which makes it incompatible with
existing CCS driver.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[Sakari Ailus: Fix set_fmt() callback a bit and idle after autosuspend.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>

The ov6650 driver was introduced in v2.6.37 to support the OMAP1-based
Amstrad Delta video phone. The platform still has a board file in the
kernel, but support for the camera was dropped in commit ce548396a433
("media: mach-omap1: board-ams-delta.c: remove soc_camera dependencies")
in v5.9. The driver has been unused since as it has received neither
ACPI nor DT support.

The ov6650 driver is one of the last sensor drivers calling
clk_set_rate(). This is deprecated, and calls to the function are being
removed to avoid cargo-cult. As the driver is unlikely to ever be used
again, drop it instead of trying to avoid call clk_set_rate().

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>

Add a v4l2 subdevice driver for the Omnivision OV2735 sensor.

The Omnivision OV2735 is a 1/2.7-Inch CMOS image sensor with an
active array size of 1920 x 1080.

The following features are supported:
- Manual exposure an gain control support
- vblank/hblank control support
- Test pattern support control
- Supported resolution: 1920 x 1080 @ 30fps (SGRBG10)

Co-developed-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Signed-off-by: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
[Sakari Ailus: Use container_of_const(), fix enum_bus_code condition.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>

OmniVision OG0VE1B is a monochrome image sensor, which produces frames in
8/10-bit raw output format and supports 640x480, 400x400, 200x200 and
100x100 output image resolution modes.

Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>