linux-toradex.git/drivers/media/i2c, branch v4.4.32 Linux kernel for Apalis and Colibri modules adv7511: TX_EDID_PRESENT is still 1 after a disconnect 2016-04-12T16:08:50+00:00 Hans Verkuil hverkuil@xs4all.nl 2016-02-10T11:32:25+00:00 454b8cbea62141cdaee224a118678c890c7aa186 commit b339a72e04a62f0b1882c43492fc712f1176b3e6 upstream. The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present. The adv7511 however still reported the EDID present after disconnecting the HDMI cable. Fix the logic regarding this control. And when the EDID is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver. This was also missing. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit b339a72e04a62f0b1882c43492fc712f1176b3e6 upstream.

The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present.
The adv7511 however still reported the EDID present after disconnecting
the HDMI cable. Fix the logic regarding this control. And when the EDID
is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver.
This was also missing.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adv7604: fix tx 5v detect regression 2016-03-09T23:34:53+00:00 Hans Verkuil hansverk@cisco.com 2016-02-10T10:09:10+00:00 f7591f1a02b5b896ba2da9855a9af24634cae2b9 commit 0ba4581c84cfb39fd527f6b3457f1c97f6356c04 upstream. The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70 again after it has already been cleared. Instead it should use the cached irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since this has already been done. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 0ba4581c84cfb39fd527f6b3457f1c97f6356c04 upstream.

The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
media: i2c: Don't export ir-kbd-i2c module alias 2016-02-17T20:30:57+00:00 Javier Martinez Canillas javier@osg.samsung.com 2016-01-27T14:03:23+00:00 3809abbacf588dc2fa020a984ddf13d9ab71e752 commit 329d88da4df9a96da43018aceabd3a06e6a7e7ae upstream. This is a partial revert of commit ed8d1cf07cb16d ("[media] Export I2C module alias information in missing drivers") that exported the module aliases for the I2C drivers that were missing to make autoload to work. But there is a bug report [0] that auto load of the ir-kbd-i2c driver cause the Hauppauge HD-PVR driver to not behave correctly. This is a hdpvr latent bug that was just exposed by ir-kbd-i2c module autoloading working and will also happen if the I2C driver is built-in or a user calls modprobe to load the module and register the driver. But there is a regression experimented by users so until the real bug is fixed, let's not export the module alias for the ir-kbd-i2c driver even when this just masks the actual issue. [0]: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=810726 Fixes: ed8d1cf07cb1 ("[media] Export I2C module alias information in missing drivers") Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 329d88da4df9a96da43018aceabd3a06e6a7e7ae upstream.

This is a partial revert of commit ed8d1cf07cb16d ("[media] Export I2C
module alias information in missing drivers") that exported the module
aliases for the I2C drivers that were missing to make autoload to work.

But there is a bug report [0] that auto load of the ir-kbd-i2c driver
cause the Hauppauge HD-PVR driver to not behave correctly.

This is a hdpvr latent bug that was just exposed by ir-kbd-i2c module
autoloading working and will also happen if the I2C driver is built-in
or a user calls modprobe to load the module and register the driver.

But there is a regression experimented by users so until the real bug
is fixed, let's not export the module alias for the ir-kbd-i2c driver
even when this just masks the actual issue.

[0]: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=810726

Fixes: ed8d1cf07cb1 ("[media] Export I2C module alias information in missing drivers")

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
remove abs64() 2015-11-09T23:11:24+00:00 Andrew Morton akpm@linux-foundation.org 2015-11-09T22:58:13+00:00 79211c8ed19c055ca105502c8733800d442a0ae6 Switch everything to the new and more capable implementation of abs(). Mainly to give the new abs() a bit of a workout. Cc: Michal Nazarewicz <mina86@mina86.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> 
Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.

Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi 2015-11-05T21:15:12+00:00 Linus Torvalds torvalds@linux-foundation.org 2015-11-05T21:15:12+00:00 75f5db39ff14ed95056f2cca3ad98c3cae97170c Pull spi updates from Mark Brown: "Quite a lot of activity in SPI this cycle, almost all of it in drivers with a few minor improvements and tweaks in the core. - Updates to pxa2xx to support Intel Broxton and multiple chip selects. - Support for big endian in the bcm63xx driver. - Multiple slave support for the mt8173 - New driver for the auxiliary SPI controller in bcm2835 SoCs. - Support for Layerscale SoCs in the Freescale DSPI driver" * tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits) spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI spi: pxa2xx: Add support for Intel Broxton spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals spi: pxa2xx: Add output control for multiple Intel LPSS chip selects spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific spi: Add DSPI support for layerscape family spi: ti-qspi: improve ->remove() callback spi/spi-xilinx: Fix race condition on last word read spi: Drop owner assignment from spi_drivers spi: Add THIS_MODULE to spi_driver in SPI core spi: Setup the master controller driver before setting the chipselect spi: dw: replace magic constant by DW_SPI_DR spi: mediatek: mt8173 spi multiple devices support spi: mediatek: handle controller_data in mtk_spi_setup spi: mediatek: remove mtk_spi_config spi: mediatek: Update document devicetree bindings to support multiple devices spi: fix kernel-doc warnings about missing return desc in spi.c spi: fix kernel-doc warnings about missing return desc in spi.h spi: pxa2xx: Align a few defines spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select ... 
Pull spi updates from Mark Brown:
 "Quite a lot of activity in SPI this cycle, almost all of it in drivers
  with a few minor improvements and tweaks in the core.

   - Updates to pxa2xx to support Intel Broxton and multiple chip selects.
   - Support for big endian in the bcm63xx driver.
   - Multiple slave support for the mt8173
   - New driver for the auxiliary SPI controller in bcm2835 SoCs.
   - Support for Layerscale SoCs in the Freescale DSPI driver"

* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
  spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
  spi: pxa2xx: Add support for Intel Broxton
  spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
  spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
  spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
  spi: Add DSPI support for layerscape family
  spi: ti-qspi: improve ->remove() callback
  spi/spi-xilinx: Fix race condition on last word read
  spi: Drop owner assignment from spi_drivers
  spi: Add THIS_MODULE to spi_driver in SPI core
  spi: Setup the master controller driver before setting the chipselect
  spi: dw: replace magic constant by DW_SPI_DR
  spi: mediatek: mt8173 spi multiple devices support
  spi: mediatek: handle controller_data in mtk_spi_setup
  spi: mediatek: remove mtk_spi_config
  spi: mediatek: Update document devicetree bindings to support multiple devices
  spi: fix kernel-doc warnings about missing return desc in spi.c
  spi: fix kernel-doc warnings about missing return desc in spi.h
  spi: pxa2xx: Align a few defines
  spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
  ...
spi: Drop owner assignment from spi_drivers 2015-10-28T01:30:17+00:00 Andrew F. Davis afd@ti.com 2015-10-23T13:59:11+00:00 3821a065f5672c430a088ae68b4da2a2d2b34106 An spi_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> 
An spi_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
[media] smiapp: Export OF module alias information 2015-10-20T16:32:05+00:00 Javier Martinez Canillas javier@osg.samsung.com 2015-07-30T16:18:49+00:00 f06d89028b35c938f9f7551e03f400037f0da82c The I2C core always reports the MODALIAS uevent as "i2c:<client name" regardless if the driver was matched using the I2C id_table or the of_match_table. So technically there's no need for a driver to export the OF table since currently it's not used. In fact, the I2C device ID table is mandatory for I2C drivers since a i2c_device_id is passed to the driver's probe function even if the I2C core used the OF table to match the driver. And since the I2C core uses different tables, OF-only drivers needs to have duplicated data that has to be kept in sync and also the dev node compatible manufacturer prefix is stripped when reporting the MODALIAS. To avoid the above, the I2C core behavior may be changed in the future to not require an I2C device table for OF-only drivers and report the OF module alias. So, it's better to also export the OF table to prevent breaking module autoloading if that happens. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> 
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.

In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.

And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.

To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] i2c: fix platform_no_drv_owner.cocci warnings 2015-10-03T14:39:48+00:00 Fengguang Wu fengguang.wu@intel.com 2015-10-01T14:25:57+00:00 edf8875f21c34102be54becfb5f435f0b7ca5a65 drivers/media/i2c/ml86v7667.c:430:3-8: No need to set .owner here. The core will do it. Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci CC: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> 
drivers/media/i2c/ml86v7667.c:430:3-8: No need to set .owner here. The core will do it.

 Remove .owner field if calls are used which set it automatically

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

CC: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] s5c73m3: fix a sparse warning 2015-10-01T21:12:39+00:00 Mauro Carvalho Chehab mchehab@osg.samsung.com 2015-10-01T21:12:39+00:00 c84a71c85b9f37abe029c600ffc02f440829df55 drivers/media/i2c/s5c73m3/s5c73m3-core.c:170:39: warning: incorrect type in argument 1 (different base types) drivers/media/i2c/s5c73m3/s5c73m3-core.c:170:39: expected restricted __be16 const [usertype] *p drivers/media/i2c/s5c73m3/s5c73m3-core.c:170:39: got unsigned short [usertype] *<noident> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> 
drivers/media/i2c/s5c73m3/s5c73m3-core.c:170:39: warning: incorrect type in argument 1 (different base types)
drivers/media/i2c/s5c73m3/s5c73m3-core.c:170:39:    expected restricted __be16 const [usertype] *p
drivers/media/i2c/s5c73m3/s5c73m3-core.c:170:39:    got unsigned short [usertype] *<noident>

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] tvp5150: add support for asynchronous probing 2015-10-01T11:42:00+00:00 Javier Martinez Canillas javier@osg.samsung.com 2015-09-21T11:23:09+00:00 c7d97499cc8ab9f9cda0af5c1b078480e198eb4c Allow the subdevice to be probed asynchronously. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> 
Allow the subdevice to be probed asynchronously.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>