The RTC on S2MPS11 is the same as S2MPS14. However interrupt numbers of
RTC alarms 0 and 1 were inversed between these two devices. So when
rtc-s5m driver requested S2MPS14_IRQ_RTCA0 interrupt, it matched to
S2MPS11_IRQ_RTCA1, not RTCA0.

Fix this by using consistent RTC alarm interrupt numbers and adding a
BUILD_BUG_ON for future generations.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds the support for Samsung S2MPS13 PMIC device to the sec-core MFD
driver. The S2MPS13 is very similar with existing S2MPS14 and includes PMIC/
RTC/CLOCK devices.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for Samsung S2MPU02 PMIC device to the MFD sec-core driver.
The S2MPU02 device includes PMIC/RTC/Clock devices.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The device type was stored in sec_pmic_dev state container twice:
 - unsigned long type (initialized from of_device_id or i2c_device_id)
 - int device_type (initialized as above or from board files when there
   is no DTS)

The 'type' field was never used outside of probe so it can be safely
removed.

Change also the device_type in sec_pmic_dev and sec_platform_data to
unsigned long to avoid any casts.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for S2MPS14 PMIC device to the MFD sec-core driver.
The S2MPS14 is similar to S2MPS11 but it has fewer regulators, two
clocks instead of three and a little different registers layout.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The S2MPS11 RTC has two alarms: alarm0 and alarm1 (corresponding
interrupts are named similarly). Use consistent names for interrupts to
limit possible errors.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add "const" to "static struct regmap_irq" and "static struct
regmap_config".

Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.

On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC.  This could be observed in various hangs,
e.g.  in infinite loop during waiting for UDR field change.

On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

reg_offset is offset of the status/mask registers. Now, since status_base
and mask_base are pointing to corresponding first registers, reg_offset
should start from 0 otheriwse regmap_add_irq_chip will fail during probe.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch support irq handling driver for s2mps11.
As this patch use regmap_irq, s5m8767 and s5m8763 are modified with
regmap_irq.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>