linux-toradex.git/drivers/mfd, branch v3.16.5 Linux kernel for Apalis and Colibri modules mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators 2014-09-17T16:21:54+00:00 Tony Lindgren tony@atomide.com 2014-08-19T15:24:05+00:00 216acfd79ec39da9e97ffd0102e00115f41aa727 commit daebabd578647440d41fc9b48d8c7a88dc2f7ab5 upstream. Commit 43fef47f94a1 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle) added support for configuring the PMIC to cut off resources during deeper idle states to save power. This however caused regression for n900 display power that needed the PMIC configuration to be disabled with commit d937678ab625 (ARM: dts: Revert enabling of twl configuration for n900). Turns out the root cause of the problem is that we must use TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling regulators that may have been enabled before the init function for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the regulator framework control the regulators like it should. Here we need to only configure the sys_clken and sys_off_mode triggers for the regulators that cannot be done by the regulator framework as it's not running at that point. This allows us to enable the PMIC configuration for n900. Fixes: 43fef47f94a1 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle) Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit daebabd578647440d41fc9b48d8c7a88dc2f7ab5 upstream.

Commit 43fef47f94a1 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.

This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab625 (ARM: dts:
Revert enabling of twl configuration for n900).

Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.

This allows us to enable the PMIC configuration for n900.

Fixes: 43fef47f94a1 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)

Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/mfd/rtsx_usb.c: export device table 2014-09-17T16:21:54+00:00 Jeff Mahoney jeffm@suse.com 2014-08-12T20:46:09+00:00 35dca0e6c20e797175ce8c5f47b03630bb397af3 commit 1813908986e36119228c158aae1c6a0267c99e77 upstream. The rtsx_usb driver contains the table for the devices it supports but doesn't export it. As a result, no alias is generated and it doesn't get loaded automatically. Via https://bugzilla.novell.com/show_bug.cgi?id=890096 Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reported-by: Marcel Witte <wittemar@googlemail.com> Cc: Roger Tseng <rogerable@realtek.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1813908986e36119228c158aae1c6a0267c99e77 upstream.

The rtsx_usb driver contains the table for the devices it supports but
doesn't export it.  As a result, no alias is generated and it doesn't
get loaded automatically.

Via https://bugzilla.novell.com/show_bug.cgi?id=890096

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Marcel Witte <wittemar@googlemail.com>
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mfd: omap-usb-host: Fix improper mask use. 2014-09-17T16:21:54+00:00 Michael Welling mwelling@emacinc.com 2014-07-28T23:01:04+00:00 7107d2df95b6b5d0af3759645a813e429fe16f78 commit 46de8ff8e80a6546aa3d2fdf58c6776666301a0c upstream. single-ulpi-bypass is a flag used for older OMAP3 silicon. The flag when set, can excite code that improperly uses the OMAP_UHH_HOSTCONFIG_UPLI_BYPASS define to clear the corresponding bit. Instead it clears all of the other bits disabling all of the ports in the process. Signed-off-by: Michael Welling <mwelling@emacinc.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 46de8ff8e80a6546aa3d2fdf58c6776666301a0c upstream.

single-ulpi-bypass is a flag used for older OMAP3 silicon.

The flag when set, can excite code that improperly uses the
OMAP_UHH_HOSTCONFIG_UPLI_BYPASS define to clear the corresponding bit.
Instead it clears all of the other bits disabling all of the ports in
the process.

Signed-off-by: Michael Welling <mwelling@emacinc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mfd: ab8500: Fix dt irq mapping 2014-06-26T12:34:15+00:00 Grygorii Strashko grygorii.strashko@ti.com 2014-06-02T16:27:58+00:00 7602e05df73f3c775d5ef808c0bc4af9711e4438 The AD8500 defines itself as interrupt-controller in DT, but it doesn't assign DT node to IRQ domain when creates it. As result, of_irq_xx() helpers don't work because they can't find necessary IRQ domain. Hence, fix it by assigning AD8500 core device DT node to IRQ domain when it's created. This patch fixes STE u8500 Snowball boot failure reported by Kevin Hilman https://lkml.org/lkml/2014/5/27/624 Reported-and-tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> 
The AD8500 defines itself as interrupt-controller in DT,
but it doesn't assign DT node to IRQ domain when creates it.
As result, of_irq_xx() helpers don't work because they can't
find necessary IRQ domain.

Hence, fix it by assigning AD8500 core device DT node to IRQ
domain when it's created.

This patch fixes STE u8500 Snowball boot failure reported by Kevin Hilman
https://lkml.org/lkml/2014/5/27/624

Reported-and-tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: davinci: Voicecodec needs regmap_mmio 2014-06-26T12:33:58+00:00 Arnd Bergmann arnd@arndb.de 2014-06-05T21:24:13+00:00 9e8884872dd4e26ec18413fe1f817bf81d023713 Without REGMAP_MMIO, building that driver results in a link error: drivers/built-in.o: In function `davinci_vc_probe': :(.init.text+0x3c1c): undefined reference to `devm_regmap_init_mmio_clk' This adds a Kconfig 'select' statement as the usual way to ensure that REGMAP_MMIO is enabled. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> 
Without REGMAP_MMIO, building that driver results in a link error:

drivers/built-in.o: In function `davinci_vc_probe':
:(.init.text+0x3c1c): undefined reference to `devm_regmap_init_mmio_clk'

This adds a Kconfig 'select' statement as the usual way to ensure
that REGMAP_MMIO is enabled.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: STw481x: Allow modular build 2014-06-26T12:33:50+00:00 Arnd Bergmann arnd@arndb.de 2014-06-05T21:24:14+00:00 f41716dc52b4a8887070318a41745e2edb612906 This driver depends on I2C, which may be a loadable module. While you'd probably want both to be built-in in practice, allowing a modular build avoids possible randconfig link errors. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> 
This driver depends on I2C, which may be a loadable module.
While you'd probably want both to be built-in in practice,
allowing a modular build avoids possible randconfig link
errors.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: UCB1x00: Enable modular build 2014-06-26T12:33:34+00:00 Arnd Bergmann arnd@arndb.de 2014-06-05T21:24:12+00:00 1c93c725d61642511f02a3293bcd7e694d0397d2 The UCB1200 / UCB1300 driver uses the MCP_SA11X0 driver, which can be a loadable module, but this results in a link error when UCB1200 itself is built-in: drivers/built-in.o: In function `ucb1x00_io_set_dir': :(.text+0x4a364): undefined reference to `mcp_reg_write' drivers/built-in.o: In function `ucb1x00_io_write': :(.text+0x4a3dc): undefined reference to `mcp_reg_write' drivers/built-in.o: In function `ucb1x00_io_read': :(.text+0x4a400): undefined reference to `mcp_reg_read' drivers/built-in.o: In function `ucb1x00_adc_enable': :(.text+0x4a460): undefined reference to `mcp_enable' ... This can easily be resolved by making CONFIG_MCP_UCB1200 itself a tristate option, since that causes Kconfig to track the dependency correctly. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> 
The UCB1200 / UCB1300 driver uses the MCP_SA11X0 driver, which
can be a loadable module, but this results in a link error
when UCB1200 itself is built-in:

drivers/built-in.o: In function `ucb1x00_io_set_dir':
:(.text+0x4a364): undefined reference to `mcp_reg_write'
drivers/built-in.o: In function `ucb1x00_io_write':
:(.text+0x4a3dc): undefined reference to `mcp_reg_write'
drivers/built-in.o: In function `ucb1x00_io_read':
:(.text+0x4a400): undefined reference to `mcp_reg_read'
drivers/built-in.o: In function `ucb1x00_adc_enable':
:(.text+0x4a460): undefined reference to `mcp_enable'
...

This can easily be resolved by making CONFIG_MCP_UCB1200 itself
a tristate option, since that causes Kconfig to track the
dependency correctly.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Merge tag 'mfd-for-linus-3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd 2014-06-12T19:42:32+00:00 Linus Torvalds torvalds@linux-foundation.org 2014-06-12T19:42:32+00:00 bae14e7a2dcb726476b5020396923a24ccc4c40b Pull more MFD updates from Lee Jones: "I missed collecting these patches due to a branch/tag naming ambiguity. Completely my own fault, as I mindlessly named a branch and tag identically. Sorry for the fuss. This pull-request contains some misplaced patches from Tony Lindgren that should have been part of the initial one" * tag 'mfd-for-linus-3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle mfd: twl4030-power: Add support for board specific configuration mfd: twl4030-power: Add recommended idle configuration mfd: twl4030-power: Add generic reset configuration mfd: twl4030-power: Fix some defines for SW_EVENTS mfd: twl4030-power: Fix hang on reboot if sleep configuration was loaded earlier 
Pull more MFD updates from Lee Jones:
 "I missed collecting these patches due to a branch/tag naming
  ambiguity.  Completely my own fault, as I mindlessly named a branch
  and tag identically.  Sorry for the fuss.

  This pull-request contains some misplaced patches from Tony Lindgren
  that should have been part of the initial one"

* tag 'mfd-for-linus-3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle
  mfd: twl4030-power: Add support for board specific configuration
  mfd: twl4030-power: Add recommended idle configuration
  mfd: twl4030-power: Add generic reset configuration
  mfd: twl4030-power: Fix some defines for SW_EVENTS
  mfd: twl4030-power: Fix hang on reboot if sleep configuration was loaded earlier
Merge tag 'mfd-for-linus-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into next 2014-06-06T19:08:39+00:00 Linus Torvalds torvalds@linux-foundation.org 2014-06-06T19:08:39+00:00 1fe9eb184721132c7254d76d9ef31c96edad8870 Pull MFD updates from Lee Jones: "Changes to existing drivers: - increase DT coverage: arizona, mc13xxx, stmpe-i2c, syscon, sun6i-prcm - regmap use of and/or clean-up: tps65090, twl6040 - basic renaming: max14577 - use new cpufreq helpers: db8500-prcmu - increase regulator support: stmpe, arizona, wm5102 - reduce legacy GPIO overhead: stmpe - provide necessary remove path: bcm590xx - expand sysfs presence: kempld - move driver specific code out to drivers: rtc-s5m, arizona - clk handling: twl6040 - use managed (devm_*) resources: ipaq-micro - clean-up/remove unused/duplicated code: tps65218, sec, pm8921, abx500-core, db8500-prcmu, menelaus - build/boot/sematic bug fixes: rtsx_usb, stmpe, bcm590xx, abx500, mc13xxx, rdc321x-southbridge, mfd-core, sec, max14577, syscon, cros_ec_spi - constify stuff: sm501, tps65910, tps6507x, tps6586x, max77686, max8997, kempld, max77693, max8907, rtsx_usb, db8500-prcmu, max8998, wm8400, sec, lp3943, max14577, as3711, omap-usb-host, ipaq-micro Support for new devices: - add support for max77836 into max14577 - add support for tps658640 into tps6586x - add support for cros-ec-i2c-tunnel into cros_ec - add new driver for rtsx_usb_sdmmc and rtsx_usb_ms - add new driver for axp20x - add new driver for sun6i-prcm - add new driver for ipaq-micro" * tag 'mfd-for-linus-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (77 commits) mfd: wm5102: Correct default for LDO Control 2 register mfd: menelaus: Use module_i2c_driver mfd: tps65218: Terminate of match table mfd: db8500-prcmu: Remove check for CONFIG_DBX500_PRCMU_DEBUG mfd: ti-keystone-devctrl: Add bindings for device state control mfd: palmas: Format the header file mfd: abx500-core: Remove unused function abx500_dump_all_banks() mfd: arizona: Correct addresses of always-on trigger registers mfd: max14577: Cast to architecture agnostic data type i2c: ChromeOS EC tunnel driver mfd: cros_ec: Sync to the latest cros_ec_commands.h from EC sources mfd: cros_ec: spi: Increase cros_ec_spi deadline from 5ms to 100ms mfd: cros_ec: spi: Make the cros_ec_spi timeout more reliable mfd: cros_ec: spi: Add mutex to cros_ec_spi mfd: cros_ec: spi: Calculate delay between transfers correctly mfd: arizona: Correct error message for addition of main IRQ chip mfd: wm8997: Add registers for high power mode mfd: arizona: Add MICVDD to mapped regulators mfd: ipaq-micro: Make mfd_cell array const mfd: ipaq-micro: Use devm_ioremap_resource() ... 
Pull MFD updates from Lee Jones:
 "Changes to existing drivers:
   - increase DT coverage: arizona, mc13xxx, stmpe-i2c, syscon,
     sun6i-prcm
   - regmap use of and/or clean-up: tps65090, twl6040
   - basic renaming: max14577
   - use new cpufreq helpers: db8500-prcmu
   - increase regulator support: stmpe, arizona, wm5102
   - reduce legacy GPIO overhead: stmpe
   - provide necessary remove path: bcm590xx
   - expand sysfs presence: kempld
   - move driver specific code out to drivers: rtc-s5m, arizona
   - clk handling: twl6040
   - use managed (devm_*) resources: ipaq-micro
   - clean-up/remove unused/duplicated code: tps65218, sec, pm8921,
     abx500-core, db8500-prcmu, menelaus
   - build/boot/sematic bug fixes: rtsx_usb, stmpe, bcm590xx, abx500,
     mc13xxx, rdc321x-southbridge, mfd-core, sec, max14577, syscon,
     cros_ec_spi
   - constify stuff: sm501, tps65910, tps6507x, tps6586x, max77686,
     max8997, kempld, max77693, max8907, rtsx_usb, db8500-prcmu,
     max8998, wm8400, sec, lp3943, max14577, as3711, omap-usb-host,
     ipaq-micro

  Support for new devices:
   - add support for max77836 into max14577
   - add support for tps658640 into tps6586x
   - add support for cros-ec-i2c-tunnel into cros_ec
   - add new driver for rtsx_usb_sdmmc and rtsx_usb_ms
   - add new driver for axp20x
   - add new driver for sun6i-prcm
   - add new driver for ipaq-micro"

* tag 'mfd-for-linus-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (77 commits)
  mfd: wm5102: Correct default for LDO Control 2 register
  mfd: menelaus: Use module_i2c_driver
  mfd: tps65218: Terminate of match table
  mfd: db8500-prcmu: Remove check for CONFIG_DBX500_PRCMU_DEBUG
  mfd: ti-keystone-devctrl: Add bindings for device state control
  mfd: palmas: Format the header file
  mfd: abx500-core: Remove unused function abx500_dump_all_banks()
  mfd: arizona: Correct addresses of always-on trigger registers
  mfd: max14577: Cast to architecture agnostic data type
  i2c: ChromeOS EC tunnel driver
  mfd: cros_ec: Sync to the latest cros_ec_commands.h from EC sources
  mfd: cros_ec: spi: Increase cros_ec_spi deadline from 5ms to 100ms
  mfd: cros_ec: spi: Make the cros_ec_spi timeout more reliable
  mfd: cros_ec: spi: Add mutex to cros_ec_spi
  mfd: cros_ec: spi: Calculate delay between transfers correctly
  mfd: arizona: Correct error message for addition of main IRQ chip
  mfd: wm8997: Add registers for high power mode
  mfd: arizona: Add MICVDD to mapped regulators
  mfd: ipaq-micro: Make mfd_cell array const
  mfd: ipaq-micro: Use devm_ioremap_resource()
  ...
Merge tag 'sound-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into next 2014-06-04T16:08:25+00:00 Linus Torvalds torvalds@linux-foundation.org 2014-06-04T16:08:25+00:00 b77279bc2e81545b20824da701b349272a78e4e7 Pull sound updates from Takashi Iwai: "At this time, majority of changes come from ASoC world while we got a few new drivers in other places for FireWire and USB. There have been lots of ASoC core cleanups / refactoring, but very little visible to external users. ASoC: - Support for specifying aux CODECs in DT - Removal of the deprecated mux and enum macros - More moves towards full componentisation - Removal of some unused I/O code - Lots of cleanups, fixes and enhancements to the davinci, Freescale, Haswell and Realtek drivers - Several drivers exposed directly in Kconfig for use with simple-card - GPIO descriptor support for jacks - More updates and fixes to the Freescale SSI, Intel and rsnd drivers - New drivers for Cirrus CS42L56, Realtek RT5639, RT5642 and RT5651 and ST STA350, Analog Devices ADAU1361, ADAU1381, ADAU1761 and ADAU1781, and Realtek RT5677 HD-audio: - Clean up Dell headset quirks - Noise fixes for Dell and Sony laptops - Thinkpad T440 dock fix - Realtek codec updates (ALC293,ALC233,ALC3235) - Tegra HD-audio HDMI support FireWire-audio: - FireWire audio stack enhancement (AMDTP, MIDI), support for incoming isochronous stream and duplex streams with timestamp synchronization - BeBoB-based devices support - Fireworks-based device support USB-audio: - Behringer BCD2000 USB device support Misc: - Clean up of a few old drivers, atmel, fm801, etc" * tag 'sound-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (480 commits) ASoC: Fix wrong argument for card remove callbacks ASoC: free jack GPIOs before the sound card is freed ALSA: firewire-lib: Remove a comment about restriction of asynchronous operation ASoC: cache: Fix error code when not using ASoC level cache ALSA: hda/realtek - Fix COEF widget NID for ALC260 replacer fixup ALSA: hda/realtek - Correction of fixup codes for PB V7900 laptop ALSA: firewire-lib: Use IEC 61883-6 compliant labels for Raw Audio data ASoC: add RT5677 CODEC driver ASoC: intel: The Baytrail/MAX98090 driver depends on I2C ASoC: rt5640: Add the function "get_clk_info" to RL6231 shared support ASoC: rt5640: Add the function of the PLL clock calculation to RL6231 shared support ASoC: rt5640: Add RL6231 class device shared support for RT5640, RT5645 and RT5651 ASoC: cache: Fix possible ZERO_SIZE_PTR pointer dereferencing error. ASoC: Add helper functions to cast from DAPM context to CODEC/platform ALSA: bebob: sizeof() vs ARRAY_SIZE() typo ASoC: wm9713: correct mono out PGA sources ALSA: synth: emux: soundfont.c: Cleaning up memory leak ASoC: fsl: Remove dependencies of boards for SND_SOC_EUKREA_TLV320 ASoC: fsl-ssi: Use regmap ASoC: fsl-ssi: reorder and document fsl_ssi_private ... 
Pull sound updates from Takashi Iwai:
 "At this time, majority of changes come from ASoC world while we got a
  few new drivers in other places for FireWire and USB.  There have been
  lots of ASoC core cleanups / refactoring, but very little visible to
  external users.

  ASoC:
   - Support for specifying aux CODECs in DT
   - Removal of the deprecated mux and enum macros
   - More moves towards full componentisation
   - Removal of some unused I/O code
   - Lots of cleanups, fixes and enhancements to the davinci, Freescale,
     Haswell and Realtek drivers
   - Several drivers exposed directly in Kconfig for use with
     simple-card
   - GPIO descriptor support for jacks
   - More updates and fixes to the Freescale SSI, Intel and rsnd drivers
   - New drivers for Cirrus CS42L56, Realtek RT5639, RT5642 and RT5651
     and ST STA350, Analog Devices ADAU1361, ADAU1381, ADAU1761 and
     ADAU1781, and Realtek RT5677

  HD-audio:
   - Clean up Dell headset quirks
   - Noise fixes for Dell and Sony laptops
   - Thinkpad T440 dock fix
   - Realtek codec updates (ALC293,ALC233,ALC3235)
   - Tegra HD-audio HDMI support

  FireWire-audio:
   - FireWire audio stack enhancement (AMDTP, MIDI), support for
     incoming isochronous stream and duplex streams with timestamp
     synchronization
   - BeBoB-based devices support
   - Fireworks-based device support

  USB-audio:
   - Behringer BCD2000 USB device support

  Misc:
   - Clean up of a few old drivers, atmel, fm801, etc"

* tag 'sound-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (480 commits)
  ASoC: Fix wrong argument for card remove callbacks
  ASoC: free jack GPIOs before the sound card is freed
  ALSA: firewire-lib: Remove a comment about restriction of asynchronous operation
  ASoC: cache: Fix error code when not using ASoC level cache
  ALSA: hda/realtek - Fix COEF widget NID for ALC260 replacer fixup
  ALSA: hda/realtek - Correction of fixup codes for PB V7900 laptop
  ALSA: firewire-lib: Use IEC 61883-6 compliant labels for Raw Audio data
  ASoC: add RT5677 CODEC driver
  ASoC: intel: The Baytrail/MAX98090 driver depends on I2C
  ASoC: rt5640: Add the function "get_clk_info" to RL6231 shared support
  ASoC: rt5640: Add the function of the PLL clock calculation to RL6231 shared support
  ASoC: rt5640: Add RL6231 class device shared support for RT5640, RT5645 and RT5651
  ASoC: cache: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
  ASoC: Add helper functions to cast from DAPM context to CODEC/platform
  ALSA: bebob: sizeof() vs ARRAY_SIZE() typo
  ASoC: wm9713: correct mono out PGA sources
  ALSA: synth: emux: soundfont.c: Cleaning up memory leak
  ASoC: fsl: Remove dependencies of boards for SND_SOC_EUKREA_TLV320
  ASoC: fsl-ssi: Use regmap
  ASoC: fsl-ssi: reorder and document fsl_ssi_private
  ...