linux-toradex.git/drivers/mmc/core/core.h, branch v3.4.2

Merge tag 'for-linus' of git://github.com/rustyrussell/linux

2012-01-14T20:32:16+00:00

Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999  BFCB D920 0E6C D1AD B8F1

* tag 'for-linus' of git://github.com/rustyrussell/linux:
  module_param: check that bool parameters really are bool.
  intelfbdrv.c: bailearly is an int module_param
  paride/pcd: fix bool verbose module parameter.
  module_param: make bool parameters really bool (drivers & misc)
  module_param: make bool parameters really bool (arch)
  module_param: make bool parameters really bool (core code)
  kernel/async: remove redundant declaration.
  printk: fix unnecessary module_param_name.
  lirc_parallel: fix module parameter description.
  module_param: avoid bool abuse, add bint for special cases.
  module_param: check type correctness for module_param_array
  modpost: use linker section to generate table.
  modpost: use a table rather than a giant if/else statement.
  modules: sysfs - export: taint, coresize, initsize
  kernel/params: replace DEBUGP with pr_debug
  module: replace DEBUGP with pr_debug
  module: struct module_ref should contains long fields
  module: Fix performance regression on modules with large symbol tables
  module: Add comments describing how the "strmap" logic works

Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries.  The
ARM sa11x0 mcp bus needed to be converted to that too.

module_param: make bool parameters really bool (drivers & misc)

2012-01-12T23:02:20+00:00

module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.

Acked-by: Mauro Carvalho Chehab 
Signed-off-by: Rusty Russell

mmc: allow upper layers to know immediately if card has been removed

2012-01-12T04:58:43+00:00

Add a function mmc_detect_card_removed() which upper layers can use to
determine immediately if a card has been removed. This function should
be called after an I/O request fails so that all queued I/O requests
can be errored out immediately instead of waiting for the card device
to be removed.

Signed-off-by: Adrian Hunter 
Acked-by: Sujit Reddy Thumma 
Signed-off-by: Chris Ball

mmc: core: Fix hangs related to insert/remove of cards

2011-10-26T20:32:01+00:00

During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.

If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.

Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.

Signed-off-by: Ulf Hansson 
Acked-by: Linus Walleij 
Cc: 
Signed-off-by: Chris Ball

mmc: core: add support for eMMC Dual Data Rate

2011-05-25T03:53:58+00:00

eMMC voltage change not required for 1.8V.  3.3V and 1.8V vcc
are capable of doing DDR. vccq of 1.8v is not required.

Signed-off-by: Philip Rakity 
Reviewed-by: Arindam Nath 
Signed-off-by: Chris Ball

mmc: core: eMMC signal voltage does not use CMD11

2011-05-25T03:53:58+00:00

eMMC chips do not use CMD11 when changing voltage.  Add extra
argument to call to indicate if CMD11 needs to be sent.

Signed-off-by: Philip Rakity 
Reviewed-by: Arindam Nath 
Signed-off-by: Chris Ball

mmc: sd: add support for driver type selection

2011-05-25T03:53:24+00:00

This patch adds support for setting driver strength during UHS-I
initialization procedure. Since UHS-I cards set S18A (bit 24) in
response to ACMD41, we use this as a base for UHS-I initialization.
We modify the parameter list of mmc_sd_get_cid() so that we can
save the ROCR from ACMD41 to check whether bit 24 is set.

We decide whether the Host Controller supports A, C, or D driver
type depending on the Capabilities register. Driver type B is
suported by default. We then set the appropriate driver type for
the card using CMD6 mode 1. As per Host Controller spec v3.00, we
set driver type for the host only if Preset Value Enable in the
Host Control2 register is not set. SDHCI_HOST_CONTROL has been
renamed to SDHCI_HOST_CONTROL1 to conform to the spec.

Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.

Signed-off-by: Arindam Nath 
Reviewed-by: Philip Rakity 
Tested-by: Philip Rakity 
Acked-by: Zhangfei Gao 
Signed-off-by: Chris Ball

mmc: sd: add support for signal voltage switch procedure

2011-05-25T01:04:38+00:00

Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.

Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.

If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.

Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.

Signed-off-by: Arindam Nath 
Reviewed-by: Philip Rakity 
Tested-by: Philip Rakity 
Acked-by: Zhangfei Gao 
Signed-off-by: Chris Ball

mmc: quirks: Extends card quirks with MMC/SD quirks matching the CID.

2011-05-25T01:00:54+00:00

The current mechanism is SDIO-only. This allows us to create
function-specific quirks, without creating messy Kconfig dependencies,
or polluting core/ with function-specific code.

Signed-off-by: Andrei Warkentin 
Acked-by: Arnd Bergmann 
Signed-off-by: Chris Ball

mmc: add per device quirk placeholder

2011-03-15T17:48:33+00:00

Some cards have quirks valid for every platforms using current
platform quirk hooks leads to a lot of code and debug duplication.

So we inspire a bit from what exists in PCI subsystem and do our own
per vendorid/deviceid quirk.  We still drop the complexity of the pci
quirk system (with special section tables, and so on).
That can be added later if needed.

Signed-off-by: Pierre Tardy 
Acked-by: Linus Walleij 
Acked-by: Ohad Ben-Cohen 
Signed-off-by: Chris Ball