linux-toradex.git/drivers/mmc, branch v4.4.160

mmc: sdhci-iproc: fix 32bit writes for TRANSFER_MODE register

2018-05-30T05:48:51+00:00

commit 5f651b870485ee60f5abbbd85195a6852978894a upstream.

When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.

Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Signed-off-by: Corneliu Doban 
Signed-off-by: Scott Branden 
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: jz4740: Fix race condition in IRQ mask update

2018-04-24T07:32:08+00:00

commit a04f0017c22453613d5f423326b190c61e3b4f98 upstream.

A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.

If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.

This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).

Resolve by holding the spinlock until after the IMASK register has
been updated.

Cc: stable@vger.kernel.org
Link: https://github.com/MIPS/CI20_linux/issues/19
Fixes: 61bfbdb85687 ("MMC: Add support for the controller on JZ4740 SoCs.")
Tested-by: Mathieu Malaterre 
Signed-off-by: Alex Smith 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occurs

2018-03-28T16:40:13+00:00

commit 47b7de2f6c18f75d1f2716efe752cba43f32a626 upstream.

It was found that in IDMAC mode after soft-reset driver switches
to PIO mode.

That's what happens in case of DTO timeout overflow calculation failure:
1. soft-reset is called
2. driver restarts dma
3. descriptors states are checked, one of descriptor is owned by the IDMAC.
4. driver can't use DMA and then switches to PIO mode.

Failure was already fixed in:
https://www.spinics.net/lists/linux-mmc/msg48125.html.

Behaviour while soft-reset is not something we except or
even want to happen. So we switch from dw_mci_idmac_reset
to dw_mci_idmac_init, so descriptors are cleaned before starting dma.

And while at it explicitly zero des0 which otherwise might
contain garbage as being allocated by dmam_alloc_coherent().

Signed-off-by: Evgeniy Didin 
Cc: Jaehoon Chung 
Cc: Ulf Hansson 
Cc: Andy Shevchenko 
Cc: Jisheng Zhang 
Cc: Shawn Lin 
Cc: Alexey Brodkin 
Cc: Eugeniy Paltsev 
Cc: linux-snps-arc@lists.infradead.org
Cc:  # 4.4+
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: avoid removing non-removable hosts during suspend

2018-03-24T09:58:47+00:00

[ Upstream commit de8dcc3d2c0e08e5068ee1e26fc46415c15e3637 ]

The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.

After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.

The conditions here are:

 1. During suspend, we reach mmc_pm_notify()

 2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
    suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
    -ENOSYS because btsdio_driver does not have a suspend method.

 3. mmc_pm_notify() proceeds to remove the card

 4. Upon resume, mmc_rescan() does nothing with this host, because of
    the rescan_entered check which aims to only scan a non-removable
    device a single time (i.e. during boot).

Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.

Signed-off-by: Daniel Drake 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046a

2018-03-24T09:58:45+00:00

[ Upstream commit a627f025eb0534052ff451427c16750b3530634c ]

The ls1046a datasheet specified that the max SD clock frequency
for eSDHC SDR104/HS200 was 167MHz, and the ls1012a datasheet
specified it's 125MHz for ls1012a. So this patch is to add the
limitation.

Signed-off-by: Yangbo Lu 
Acked-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: host: omap_hsmmc: checking for NULL instead of IS_ERR()

2018-03-24T09:58:43+00:00

[ Upstream commit ec5ab8933772c87f24ad62a4a602fe8949f423c2 ]

devm_pinctrl_get() returns error pointers, it never returns NULL.

Fixes: 455e5cd6f736 ("mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x")
Signed-off-by: Dan Carpenter 
Reviewed-by: Kishon Vijay Abraham I 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-esdhc: add/remove some quirks according to vendor version

2018-01-31T11:06:09+00:00

commit 1ef5e49e46b919052474d9b54a15debc79ff0133 upstream.

A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
	u32 vvn;

	vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
	vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
	if (vvn == VENDOR_V_22)
		host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;

	if (vvn > VENDOR_V_22)
		host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}

This patch is used to fix it by add/remove some quirks according to
verdor version in probe.

Signed-off-by: Yangbo Lu 
Fixes: f4932cfd22f1 ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: Ulf Hansson 
Signed-off-by: Matthias Brugger 
Signed-off-by: Greg Kroah-Hartman

mmc: mediatek: Fixed bug where clock frequency could be set wrong

2017-12-20T09:04:55+00:00

[ Upstream commit 40ceda09c8c84694c2ca6b00bcc6dc71e8e62d96 ]

This patch can fix two issues:

Issue 1:
In previous code, div may be overflow when setting clock frequency
as f_min. We can use DIV_ROUND_UP to fix this boundary related
issue.

Issue 2:
In previous code, we can not set the correct clock frequency when
div equals 0xff.

Signed-off-by: Yong Mao 
Signed-off-by: Chaotian Jing 
Reviewed-by: Daniel Kurtz 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: core: Do not leave the block driver in a suspended state

2017-12-05T10:22:51+00:00

commit ebe7dd45cf49e3b49cacbaace17f9f878f21fbea upstream.

The block driver must be resumed if the mmc bus fails to suspend the card.

Signed-off-by: Adrian Hunter 
Reviewed-by: Linus Walleij 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: s3cmci: include linux/interrupt.h for tasklet_struct

2017-11-08T09:06:28+00:00

[ Upstream commit e1c6ec26b853e9062f0b3daaf695c546d0702953 ]

I got this new build error on today's linux-next

drivers/mmc/host/s3cmci.h:69:24: error: field 'pio_tasklet' has incomplete type
  struct tasklet_struct pio_tasklet;
drivers/mmc/host/s3cmci.c: In function 's3cmci_enable_irq':
drivers/mmc/host/s3cmci.c:390:4: error: implicit declaration of function 'enable_irq';did you mean 'enable_imask'? [-Werror=implicit-function-declaration]

While I haven't found out why this happened now and not earlier, the
solution is obvious, we should include the header that defines
the structure.

Signed-off-by: Arnd Bergmann 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman