The following patch fixes:
 - re-initialization of host->col_addr which is used as byte index
   between the successive READID flash commands.
 - compile error when CONFIG_PM is enabled
 - pass on the error code from clk_get()
 - return -ENOMEM in case of failed ioremap()
 - pass on the return value of platform_driver_probe() directly
 - remove excessive printk
 - let command line partition table parsing with mxc_nand name.
   The cmd_line parsing is done via <mtd-id> name that differs
   from mxc_nand by default and looks like "NAND 256MiB 1,8V 8-bit"

Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

* git://git.infradead.org/mtd-2.6:
  mtd: fix timeout in M25P80 driver
  mtd: Bug in m25p80.c during whole-chip erase
  mtd: expose subpage size via sysfs
  mtd: mtd in mtd_release is unused without CONFIG_MTD_CHAR

Extend erase timeout in M25P80 SPI Flash driver.

The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.

Signed-off-by: Peter Horton <zero@colonel-panic.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There is a logic error in "whole chip erase" for the m25p80 family.  If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase.  This patch corrects that.

Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc.  Increasing it allows me to successfully program
the device on my board.

Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Wrong types on IRQ handler

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MTD has got sysfs support in 2.6.30-rc1. But subpage size is not
exposed there - do this.

UBI utilities badly need this parameter. At the moment there is
no way to get subpage size - ioctls do not return it. And we
just got sysfs support, so we can easilly extend it with this
additional parameter.

This can be merged late in the development cycle because:
1. sysfs support has been just added - there are no users for
   it so far, even.
2. UBI utilities really need this parameter, and it is better
   not to delay this.

Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

drivers/mtd/mtdcore.c: In function 'mtd_release':
drivers/mtd/mtdcore.c:51: warning: unused variable 'mtd'

[akpm: make it actually build]
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* 'linux-next' of git://git.infradead.org/ubi-2.6:
  UBI: add fsync capability