linux-toradex.git/drivers/mtd, branch v3.2-rc5

MTD: MAPS: bcm963xx-flash.c: explicitly include module.h

2011-11-08T02:26:55+00:00

module.h was previously implicitly included through mtd/mtd.h.

Fixes the following build failure after the module.h cleanup:

  CC      drivers/mtd/maps/bcm963xx-flash.o
drivers/mtd/maps/bcm963xx-flash.c: In function 'bcm963xx_probe':
drivers/mtd/maps/bcm963xx-flash.c:208:29: error: 'THIS_MODULE' undeclared (first use in this function)
 [...]
drivers/mtd/maps/bcm963xx-flash.c:276:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/mtd/maps/bcm963xx-flash.c:276:15: warning: function declaration isn't a prototype
make[7]: *** [drivers/mtd/maps/bcm963xx-flash.o] Error 1

Signed-off-by: Jonas Gorski 
Signed-off-by: Paul Gortmaker

Merge git://git.infradead.org/mtd-2.6

2011-11-07T17:11:16+00:00

* git://git.infradead.org/mtd-2.6: (226 commits)
  mtd: tests: annotate as DANGEROUS in Kconfig
  mtd: tests: don't use mtd0 as a default
  mtd: clean up usage of MTD_DOCPROBE_ADDRESS
  jffs2: add compr=lzo and compr=zlib options
  jffs2: implement mount option parsing and compression overriding
  mtd: nand: initialize ops.mode
  mtd: provide an alias for the redboot module name
  mtd: m25p80: don't probe device which has status of 'disabled'
  mtd: nand_h1900 never worked
  mtd: Add DiskOnChip G3 support
  mtd: m25p80: add EON flash EN25Q32B into spi flash id table
  mtd: mark block device queue as non-rotational
  mtd: r852: make r852_pm_ops static
  mtd: m25p80: add support for at25df321a spi data flash
  mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
  mtd: nand: switch `check_pattern()' to standard `memcmp()'
  mtd: nand: invalidate cache on unaligned reads
  mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
  mtd: nand: wait to set BBT version
  mtd: nand: scrub BBT on ECC errors
  ...

Fix up trivial conflicts:
 - arch/arm/mach-at91/board-usb-a9260.c
	Merged into board-usb-a926x.c
 - drivers/mtd/maps/lantiq-flash.c
	add_mtd_partitions -> mtd_device_register vs changed to use
	mtd_device_parse_register.

Merge branch 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux

2011-11-07T03:44:47+00:00

* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
  Revert "tracing: Include module.h in define_trace.h"
  irq: don't put module.h into irq.h for tracking irqgen modules.
  bluetooth: macroize two small inlines to avoid module.h
  ip_vs.h: fix implicit use of module_get/module_put from module.h
  nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
  include: replace linux/module.h with "struct module" wherever possible
  include: convert various register fcns to macros to avoid include chaining
  crypto.h: remove unused crypto_tfm_alg_modname() inline
  uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
  pm_runtime.h: explicitly requires notifier.h
  linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
  miscdevice.h: fix up implicit use of lists and types
  stop_machine.h: fix implicit use of smp.h for smp_processor_id
  of: fix implicit use of errno.h in include/linux/of.h
  of_platform.h: delete needless include 
  acpi: remove module.h include from platform/aclinux.h
  miscdevice.h: delete unnecessary inclusion of module.h
  device_cgroup.h: delete needless include 
  net: sch_generic remove redundant use of 
  net: inet_timewait_sock doesnt need 
  ...

Fix up trivial conflicts (other header files, and  removal of the ab3550 mfd driver) in
 - drivers/media/dvb/frontends/dibx000_common.c
 - drivers/media/video/{mt9m111.c,ov6650.c}
 - drivers/mfd/ab3550-core.c
 - include/linux/dmaengine.h

Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

2011-11-03T20:28:14+00:00

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (37 commits)
  MIPS: O32: Provide definition of registers ta0 .. ta3.
  MIPS: perf: Add Octeon support for hardware perf.
  MIPS: perf: Add support for 64-bit perf counters.
  MIPS: perf: Reorganize contents of perf support files.
  MIPS: perf: Cleanup formatting in arch/mips/kernel/perf_event.c
  MIPS: Add accessor macros for 64-bit performance counter registers.
  MIPS: Add probes for more Octeon II CPUs.
  MIPS: Add more CPU identifiers for Octeon II CPUs.
  MIPS: XLR, XLS: Add comment for smp setup
  MIPS: JZ4740: GPIO: Check correct IRQ in demux handler
  MIPS: JZ4740: GPIO: Simplify IRQ demuxer
  MIPS: JZ4740: Use generic irq chip
  MIPS: Alchemy: remove all CONFIG_SOC_AU1??? defines
  MIPS: Alchemy: kill au1xxx.h header
  MIPS: Alchemy: clean DMA code of CONFIG_SOC_AU1??? defines
  MIPS, IDE: Alchem, au1xxx-ide: Remove pb1200/db1200 header dep
  MIPS: Alchemy: Redo PCI as platform driver
  MIPS: Alchemy: more base address cleanup
  MIPS: Alchemy: rewrite USB platform setup.
  MIPS: Alchemy: abstract USB block control register access
  ...

Fix up trivial conflicts in:
	arch/mips/alchemy/devboards/db1x00/platform.c
	drivers/ide/Kconfig
	drivers/mmc/host/au1xmmc.c
	drivers/video/Kconfig
	sound/mips/Kconfig

filesystems: add missing nlink wrappers

2011-11-02T11:53:43+00:00

Replace direct i_nlink updates with the respective updater function
(inc_nlink, drop_nlink, clear_nlink, inode_dec_link_count).

Signed-off-by: Miklos Szeredi

mtd: Add module.h to drivers users that were implicitly using it.

2011-10-31T23:31:12+00:00

We are cleaning up the implicit presence of module.h that these
drivers are taking advantage of.  Fix them in advance of the
cleanup operation.

Signed-off-by: Paul Gortmaker

mtd: Add export.h for EXPORT_SYMBOL/THIS_MODULE where needed

2011-10-31T23:31:11+00:00

These two common macros will be no longer present everywhere.
Call out the include needs of them explicitly where required.

Signed-off-by: Paul Gortmaker

mtd: tests: annotate as DANGEROUS in Kconfig

2011-10-30T20:33:30+00:00

The tests may erase mtd devices, so annotate them as suggested per
coding style and add a paragraph to the help text as well.

Artem: amended the help test a bit.

Signed-off-by: Wolfram Sang 
Signed-off-by: Artem Bityutskiy

mtd: tests: don't use mtd0 as a default

2011-10-30T12:31:04+00:00

mtd tests may erase the mtd device, so force the user to specify which
mtd device to test by using the module parameter. Disable the default
(using mtd0) since this may destroy a vital part of the flash if the
module is inserted accidently or carelessly.

Reported-by: Roland Kletzing 
Signed-off-by: Wolfram Sang 
Signed-off-by: Artem Bityutskiy

mtd: clean up usage of MTD_DOCPROBE_ADDRESS

2011-10-30T12:22:36+00:00

Depending on whether MTD_DOCPROBE_ADVANCED is set or not,
MTD_DOCPROBE_ADDRESS will default to either 0x0000 or 0. That should
lead to (basically) identical code in docprobe.c. The current two
defaults should be merged.

And, while we're at it, if MTD_DOCPROBE is set MTD_DOCPROBE_ADDRESS will
always be set. (MTD_DOCPROBE_ADDRESS depends on MTD_DOCPROBE and it has
a default value.) So the check whether CONFIG_MTD_DOCPROBE_ADDRESS is
defined is unnecessary and should be dropped.

Signed-off-by: Paul Bolle 
Signed-off-by: Artem Bityutskiy