The allocated RX buffer size was 64 bytes bigger than the PCI mapped size with no good reason. If the packet was actually using the buffer up to its limit and if the last 64 bytes of the buffer crossed 4KB boundary then an unmapped PCI page was accessed. The fix is to use only one parameter for the buffer size - there is no need to differentiate between the buffer size and the PCI mapping size since the extra 64 bytes can actually be used by the FW to align the Ethernet payload to 64 bytes. Also updating the driver version and date Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The has Rx work check was wrong: when the FW was at the end of the page, the driver was already at the beginning of the next page. Since the check only validated that both driver and FW are pointing to the same place, it concluded that there is still work to be done. This caused some serious issues including long latency results on ping-pong test and lockups while unloading the driver in that condition. Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch compliance The latest version of checkpatch found the following style errors in the code Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistakes Spelling has to L's in it... Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Minor code improvements Small changes to make the code a little bit more efficient and mostly more readable: - Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR - Removing the NIG_WR since it did nothing and was only confusing - On bnx2x_panic_dump, print only the used parts of the rings - define parameters only on the branch they are needed and not at the beginning of the function - using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1G LED does not turn off The 1G LED was not switched to off when the link was lost Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Change GPIO for any port The set GPIO function should receive the port index to allow changing the GPIO of another port. This is needed for the common init phase (one the first driver is loaded for the chip) Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
HW attention lock Making sure that only one function will handle the HW attention. This makes the device parameter aeu_mask redundant so it is removed Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Load/Unload under traffic Few issues were found when loading and unloading under traffic: - When receiving Tx interrupt call netif_wake_queue if the queue is stopped but the state is open - Check that interrupts are enabled before doing anything else on the msix_fp_int function - In nic_load, enable the interrupts only when needed and ready for it - Function stop_leading returns status since it can fail - Add 1ms delay when unloading the driver to validate that there are no open transactions that already started by the FW - Splitting the "has work" function into Tx and Rx so the same function will be used on unload and interrupts - Do not request for WoL if only resetting the device (save the time that it takes the FW to set the link after reset) - Fixing the device reset after iSCSI boot and before driver load - all internal buffers must be cleared before the driver is loaded Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics - Making sure that each drop is accounted for in the driver statistics - Clearing the FW statistics when driver is loaded to prevent inconsistency with HW statistics - Once error is detected (bnx2x_panic_dump), stop the statistics before other actions (currently it is stopped last and can corrupt the data) - Adding HW checksum error counter to the statistics - Removing unused variable stats_ticks - Using macros instead of magic numbers to indicate which statistics are shared per port and which are per function Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>