Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.

CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After resetting BCM54618se, link partner would still see link since the PHY wasn't put into low-power state.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BCM84833 fail to link due to incorrect auto-negotiation setting.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix no-link issue on BCM578xx when direct attached cable is connected since Warpcore microcode restart was missing to re-read the new mode.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fix resolve two problems seen regarding LED:
1. LED doesn't flash during port identification.
2. Traffic LED sometimes do not blink.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix MDIO access to Warpcore on new chip version of 578xx.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix couple of issues of remote fault detection and handling:
Link may go down due to remote fault indications during link establishment.
Possible link down after primary function migration.
Remote fault was not detected on 578xx.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a problem in which the 578xx chip hangs after running traffic, and then pulling the network cable.
This occurs since TX pipe is stalled due to missing XON indication towards the NIG.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>