linux-toradex.git/drivers/net/dsa, branch v5.0

net: dsa: mv88e6xxx: Fix statistics on mv88e6161

2019-03-02T08:45:04+00:00

Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.

Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c394900 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode

2019-03-02T05:37:05+00:00

When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.

Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.

v2:
- add small helper and init the number of actual ports only

Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller

net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X

2019-02-28T23:16:06+00:00

Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.

Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.

This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.

Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.

This was tested on 6390X using RXAUI mode.

Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: dsa: mv88e6xxx: Fix u64 statistics

2019-02-28T20:53:02+00:00

The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined.  Fix
the combing, which wrongly worked on u16's.

Fixes: 80c4627b2719 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy 
Signed-off-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: dsa: lantiq: Add GPHY firmware files

2019-02-25T01:34:54+00:00

This adds the file names of the FW files which this driver handles into
the module description.

Signed-off-by: Hauke Mehrtens 
Signed-off-by: David S. Miller

net: dsa: b53: Do not program CPU port's PVID

2019-02-16T04:37:54+00:00

The CPU port is special and does not need to obey VLAN restrictions as
far as untagged traffic goes, also, having the CPU port be part of a
particular PVID is against the idea of keeping it tagged in all VLANs.

Fixes: ca8931948344 ("net: dsa: b53: Keep CPU port as tagged in all VLANs")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: dsa: bcm_sf2: Do not assume DSA master supports WoL

2019-02-16T04:37:54+00:00

We assume in the bcm_sf2 driver that the DSA master network device
supports ethtool_ops::{get,set}_wol operations, which is not a given.
Avoid de-referencing potentially non-existent function pointers and
check them as we should.

Fixes: 96e65d7f3f88 ("net: dsa: bcm_sf2: add support for Wake-on-LAN")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: dsa: b53: Properly account for VLAN filtering

2019-02-16T04:37:54+00:00

VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.

Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: dsa: b53: Fix default VLAN ID

2019-02-16T04:37:54+00:00

We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.

Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()

2019-02-14T06:11:53+00:00

The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS.  The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions.  The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.

Fixes: 8cfa94984c9c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter 
Reviewed-by: Vivien Didelot 
Signed-off-by: David S. Miller