linux-toradex.git/drivers/net/ks8842.c, branch v3.0.41

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

2011-06-04T14:16:00+00:00

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
  tg3: Fix tg3_skb_error_unmap()
  net: tracepoint of net_dev_xmit sees freed skb and causes panic
  drivers/net/can/flexcan.c: add missing clk_put
  net: dm9000: Get the chip in a known good state before enabling interrupts
  drivers/net/davinci_emac.c: add missing clk_put
  af-packet: Add flag to distinguish VID 0 from no-vlan.
  caif: Fix race when conditionally taking rtnl lock
  usbnet/cdc_ncm: add missing .reset_resume hook
  vlan: fix typo in vlan_dev_hard_start_xmit()
  net/ipv4: Check for mistakenly passed in non-IPv4 address
  iwl4965: correctly validate temperature value
  bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
  ath9k: fix two more bugs in tx power
  cfg80211: don't drop p2p probe responses
  Revert "net: fix section mismatches"
  drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
  sctp: stop pending timers and purge queues when peer restart asoc
  drivers/net: ks8842 Fix crash on received packet when in PIO mode.
  ip_options_compile: properly handle unaligned pointer
  iwlagn: fix incorrect PCI subsystem id for 6150 devices
  ...

drivers/net: ks8842 Fix crash on received packet when in PIO mode.

2011-05-31T22:14:31+00:00

This patch fixes a driver crash during packet reception due to not enough
bytes allocated in the skb. Since the loop reads out 4 bytes at a time, we
need to allow for up to 3 bytes of slack space.

Signed-off-by: Dennis Aberilla 
Signed-off-by: David S. Miller

mfd: Use mfd cell platform_data for timberdale cells platform bits

2011-05-26T17:45:05+00:00

With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Acked-by: Richard Röjfors 
Signed-off-by: Samuel Ortiz

Fix common misspellings

2011-03-31T14:26:23+00:00

Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi

mfd: mfd_cell is now implicitly available to timberdale drivers

2011-03-23T09:41:52+00:00

The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.

Note that the mfd's platform_data is marked __devinitdata.  This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.

Signed-off-by: Andres Salomon 
Signed-off-by: Samuel Ortiz

ks8842: Fix warnings on 64-bit.

2010-07-28T05:24:37+00:00

drivers/net/ks8842.c:922:26: warning: cast from pointer to integer of different size
drivers/net/ks8842.c:940:17: warning: cast to pointer from integer of different size
drivers/net/ks8842.c:963:17: warning: cast to pointer from integer of different size

Signed-off-by: David S. Miller

ks8842: Support DMA when accessed via timberdale

2010-07-28T03:48:19+00:00

This patch adds support for RX and TX DMA via the DMA API,
this is only supported when the KS8842 is accessed via timberdale.

There is no support for DMA on the generic bus interface it self,
a state machine inside the FPGA is handling RX and TX transfers to/from
buffers in the FPGA. The host CPU can do DMA to and from these buffers.

The FPGA has to handle the RX interrupts, so these must be enabled in
the ks8842 but not in the FPGA. The driver must not disable the RX interrupt
that would mean that the data transfers into the FPGA buffers would stop.

The host shall not enable TX interrupts since TX is handled by the FPGA,
the host is notified by DMA callbacks when transfers are finished.

Which DMA channels to use are added as parameters in the platform data struct.

Signed-off-by: Richard Röjfors 
Signed-off-by: David S. Miller

ks8842: Support 100Mbps when accessed via timberdale

2010-07-27T04:05:03+00:00

This patch removes the code which disables 100Mbps advertising when
the ks8842 is accessed via timberdale.

At higher speed it's good to be nice to the internal state machine
of timberdale by acking interrupts. That is done by a write to the
interrupt ack register (IAR).

Signed-off-by: Richard Röjfors 
Signed-off-by: David S. Miller

ks8842: Fix ks8842_tx_frame() for 16bit case.

2010-07-19T22:25:04+00:00

As reported by Andrew:

drivers/net/ks8842.c: In function 'ks8842_handle_rx':
drivers/net/ks8842.c:428: warning: 'status' may be used uninitialized in this function

Just use the 32-bit status for all reads, and delete the useless
cast to 'int' when reading a u16 into 'len'.

Reported-by: Andrew Morton 
Signed-off-by: David S. Miller

drivers/net: Add Micrel KS8841/42 support to ks8842 driver

2010-07-13T17:13:49+00:00

Body of the explanation:
   -support 16bit and 32bit bus width.
   -add device reset for ks8842/8841 Micrel device.
   -set 100Mbps as a default for Micrel device.
   -set MAC address in both MAC/Switch layer with different sequence for Micrel
    device, as mentioned in data sheet.
   -use private data to set options both 16/32bit bus width and Micrel device/
    Timberdale(FPGA).
   -update Kconfig in order to put more information about ks8842 device.

Signed-off-by: David J. Choi 
Signed-off-by: David S. Miller