The mlx4_en module now uses the new steering mechanism.
The RX packets are now steered through the MCG table instead
of Mac table for unicast, and default entry for multicast.
The feature is enabled through INIT_HCA

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.

Signed-off-by: Igor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel warning message added in commit 58d74bb1d9f7 ("mlx4_core:
Workaround firmware bug in query dev cap") about mlx4 reporting the
wrong number of "blue flame registers" doesn't really help anyone, since
the firmware bug is known and fixed and the bug is pretty much harmless
to users.  So just get rid of the warning.

Signed-off-by: Roland Dreier <rolandd@cisco.com>

ConnectX firmware is supposed to report the number blue flame
registers per page as log2 of the value.  However, due to a firmware
bug, it reports actual number.  This patch works around this by
checking if the number of registers calculated fits within a page.  If
it does not, we use 8 registers per page.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
  IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
  IB/qib: Allow driver to load if PCIe AER fails
  IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
  IB/qib: Fix extra log level in qib_early_err()
  RDMA/cxgb4: Remove unnecessary KERN_<level> use
  RDMA/cxgb3: Remove unnecessary KERN_<level> use
  IB/core: Add link layer type information to sysfs
  IB/mlx4: Add VLAN support for IBoE
  IB/core: Add VLAN support for IBoE
  IB/mlx4: Add support for IBoE
  mlx4_en: Change multicast promiscuous mode to support IBoE
  mlx4_core: Update data structures and constants for IBoE
  mlx4_core: Allow protocol drivers to find corresponding interfaces
  IB/uverbs: Return link layer type to userspace for query port operation
  IB/srp: Sync buffer before posting send
  IB/srp: Use list_first_entry()
  IB/srp: Reduce number of BUSY conditions
  IB/srp: Eliminate two forward declarations
  IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
  IB: Replace EXTRA_CFLAGS with ccflags-y
  ...

Add fields to hardware data structures and add new constants required for IBoE
support.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The report now based on query from FW, giving the correct tranciever type
and link speed.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
   on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>