If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth
allocates a couple of extra bytes at the start of each receive buffer
to make the data payload end up on a cache line boundary.
These extra bytes are skb_reserve()'d before DMA mapping, so they
should not be included in the DMA map byte count (as the mapping is
done starting at skb->data), nor should they be included in the
receive descriptor buffer size field, or the hardware can end up
DMAing beyond the end of the buffer, which can happen if someone
sends us a larger-than-MTU sized packet.
This problem was introduced in commit 7fd96ce47ff ("mv643xx_eth:
rework receive skb cache alignment", May 6 2009), but hasn't appeared
to be problematic so far, probably as the main users of mv643xx_eth
all have NET_SKB_PAD == L1_CACHE_BYTES.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for valid hw address. Signed-off-by: Denis Kirjanov <kirjanov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The txq_set_wrr() function in drivers/net/mv643xx_eth.c is unused, not even referenced under #if 0 or something like that, which results in a compile-time warning: drivers/net/mv643xx_eth.c:1070: warning: 'txq_set_wrr' defined but not used Fix: remove it. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
The Unicast Promiscious Mode (UPM) bit in the mv643xx_eth port configuration register doesn't do exactly what its name would suggest: setting this bit merely enables reception of all unicast frames with a destination address that differs from our local MAC address in bits [47:4]. In particular, it doesn't have any effect on unicast frames with a destination address that matches our MAC address in bits [47:4] -- these will still be tested against the 16-entry unicast address filter table. Therefore, if the interface is set to promiscuous mode, just setting the unicast promiscuous bit isn't enough -- we need to set all filter bits in the unicast filter table to 1 as well. Reported-by: Sachin Sanap <ssanap@marvell.com> Signed-off-by: Prabhanjan Sarnaik <sarnaik@marvell.com> Tested-by: Siddarth Gore <gores@marvell.com> Tested-by: Mahavir Jain <mjain@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Cc: stable@kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is inspired by patch recently posted by Johannes Berg. Basically what my patch does is to group list and a count of addresses into newly introduced structure netdev_hw_addr_list. This brings us two benefits: 1) struct net_device becames a bit nicer. 2) in the future there will be a possibility to operate with lists independently on netdevices (with exporting right functions). I wanted to introduce this patch before I'll post a multicast lists conversion. Signed-off-by: Jiri Pirko <jpirko@redhat.com> drivers/net/bnx2.c | 4 +- drivers/net/e1000/e1000_main.c | 4 +- drivers/net/ixgbe/ixgbe_main.c | 6 +- drivers/net/mv643xx_eth.c | 2 +- drivers/net/niu.c | 4 +- drivers/net/virtio_net.c | 10 ++-- drivers/s390/net/qeth_l2_main.c | 2 +- include/linux/netdevice.h | 17 +++-- net/core/dev.c | 130 ++++++++++++++++++-------------------- 9 files changed, 89 insertions(+), 90 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using previously introduced struct netdev_hw_addr. It also relaxes the locking. Original spinlock (still used for multicast addresses) is not needed and is no longer used for a protection of this list. All reading and writing takes place under rtnl (with no changes). I also removed a possibility to specify the length of the address while adding or deleting unicast address. It's always dev->addr_len. The convertion touched especially e1000 and ixgbe codes when the change is not so trivial. Signed-off-by: Jiri Pirko <jpirko@redhat.com> drivers/net/bnx2.c | 13 +-- drivers/net/e1000/e1000_main.c | 24 +++-- drivers/net/ixgbe/ixgbe_common.c | 14 ++-- drivers/net/ixgbe/ixgbe_common.h | 4 +- drivers/net/ixgbe/ixgbe_main.c | 6 +- drivers/net/ixgbe/ixgbe_type.h | 4 +- drivers/net/macvlan.c | 11 +- drivers/net/mv643xx_eth.c | 11 +- drivers/net/niu.c | 7 +- drivers/net/virtio_net.c | 7 +- drivers/s390/net/qeth_l2_main.c | 6 +- drivers/scsi/fcoe/fcoe.c | 16 ++-- include/linux/netdevice.h | 18 ++-- net/8021q/vlan.c | 4 +- net/8021q/vlan_dev.c | 10 +- net/core/dev.c | 195 +++++++++++++++++++++++++++----------- net/dsa/slave.c | 10 +- net/packet/af_packet.c | 4 +- 18 files changed, 227 insertions(+), 137 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts: drivers/scsi/fcoe/fcoe.c
After 2.6.29, PPC no more admits passing NULL to the dev parameter of the DMA API. The result is a BUG followed by solid lock-up when the mv643xx_eth driver brings an interface up. The following patch makes the driver work on my Pegasos again; it is mostly a search and replace of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping functions. Signed-off-by: Gabriel Paubert <paubert@iram.es> Acked-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It is not a good idea to blindly unmask the RX and TX_END interrupts for all eight queues on all mv643xx_eth hardware, since some variations of the hardware have less than eight transmit/receive queues, and the RX/TX_END interrupts for the queues they don't have can be in use by other interrupt sources. Signed-off-by: Saeed Bishara <saeed@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>