linux-toradex.git/drivers/net/phy/Makefile, branch v3.6.1

netdev/phy: Add driver for Broadcom BCM87XX 10G Ethernet PHYs

2012-06-28T04:23:25+00:00

Add a driver for BCM8706 and BCM8727 devices.  These are a 10Gig PHYs
which use MII_ADDR_C45 addressing.  They are always 10G full duplex, so
there is no autonegotiation.  All we do is report link state and send
interrupts when it changes.

If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.

Signed-off-by: David Daney 
Signed-off-by: David S. Miller

netdev/of/phy: Add MDIO bus multiplexer driven by GPIO lines.

2012-05-08T02:58:09+00:00

The GPIO pins select which sub bus is connected to the master.

Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.

Signed-off-by: David Daney 
Signed-off-by: David S. Miller

netdev/of/phy: Add MDIO bus multiplexer support.

2012-05-08T02:58:09+00:00

This patch adds a somewhat generic framework for MDIO bus
multiplexers.  It is modeled on the I2C multiplexer.

The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.

Conceptually it could look something like this:

                   ------------------
                   | Control Signal |
                   --------+---------
                           |
 ---------------   --------+------
 | MDIO MASTER |---| Multiplexer |
 ---------------   --+-------+----
                     |       |
                     C       C
                     h       h
                     i       i
                     l       l
                     d       d
                     |       |
     ---------       A       B   ---------
     |       |       |       |   |       |
     | PHY@1 +-------+       +---+ PHY@1 |
     |       |       |       |   |       |
     ---------       |       |   ---------
     ---------       |       |   ---------
     |       |       |       |   |       |
     | PHY@2 +-------+       +---+ PHY@2 |
     |       |                   |       |
     ---------                   ---------

This framework configures the bus topology from device tree data.  The
mechanics of switching the multiplexer is left to device specific
drivers.

The follow-on patch contains a multiplexer driven by GPIO lines.

Signed-off-by: David Daney 
Signed-off-by: David S. Miller

phy: add am79c874 PHY support

2012-03-19T22:02:05+00:00

Signed-off-by: Heiko Schocher 
Signed-off-by: Anatolij Gustschin 
Signed-off-by: David S. Miller

phy: Micrel KS8995MA 5-ports 10/100 managed Ethernet switch support added

2011-12-19T21:30:40+00:00

Signed-off-by: Gabor Juhos 
Signed-off-by: Frederic Lambert 
Signed-off-by: David S. Miller

ptp: Added a clock driver for the National Semiconductor PHYTER.

2011-05-23T20:10:23+00:00

This patch adds support for the PTP clock found on the DP83640.
The basic clock operations and one external time stamp have
been implemented.

Signed-off-by: Richard Cochran 
Signed-off-by: John Stultz

drivers/net/phy: micrel phy driver

2010-05-03T22:43:26+00:00

This is the first version of phy driver from Micrel Inc.

Signed-off-by: David J. Choi 
Signed-off-by: David S. Miller

NET: Add driver for Octeon MDIO buses.

2009-12-17T01:56:58+00:00

The Octeon SOC has two types of Ethernet ports, each type with its own
driver.  However, the PHYs for all the ports are controlled by a
common MDIO bus.  Because the mdio driver is not associated with a
particular driver, but is instead a system level resource, we create s
stand-alone driver for it.

As for the driver, we put the register definitions in
arch/mips/include/asm/octeon where most of the other Octeon register
definitions live.  This is a platform driver with the platform device
for "mdio-octeon" being registered in the platform startup code.

Signed-off-by: David Daney 
Acked-by: David S. Miller 
Signed-off-by: Ralf Baechle

MIPS: BCM63XX: Add integrated ethernet PHY support for phylib.

2009-07-08T02:23:51+00:00

Signed-off-by: Maxime Bizon 
Signed-off-by: Ralf Baechle 

 drivers/net/phy/Kconfig   |    6 ++
 drivers/net/phy/Makefile  |    1
 drivers/net/phy/bcm63xx.c |  132 ++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 139 insertions(+)
 create mode 100644 drivers/net/phy/bcm63xx.c
Signed-off-by: David S. Miller

phy: Add LSI ET1011C PHY driver

2008-12-10T06:21:25+00:00

Adds LSI ET1011C PHY driver. 
This driver is used by TI DM646x EVM.

Signed-off-by: Chaithrika U S 
Signed-off-by: David S. Miller