linux-toradex.git/drivers/net/phy/amd-xgbe-phy.c, branch v3.19-rc5

net: phy: replace phy_drivers_register calls

2014-11-12T18:52:53+00:00

Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.

Tested using Micrel driver, and otherwise compile-tested only.

Signed-off-by: Johan Hovold 
Signed-off-by: David S. Miller

amd-xgbe-phy: Sync PCS and PHY modes after reset

2014-11-06T02:50:12+00:00

This patch adds support to sync the states of the PCS and the PHY
after a reset is performed.  If the PCS and the PHY are not in the
same state after reset an extra mode change would be performed. This
extra mode change might not be needed if the PCS and the PHY are
synced up after reset.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

amd-xgbe-phy: Fix build break for missing declaration

2014-09-07T18:21:31+00:00

A previous patch inadvertently deleted a declaration in the
amd_xgbe_an_tx_training function causing the build to fail.

Add the declaration for 'priv' back to the function.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

amd-xgbe-phy: Checkpatch driver fixes

2014-09-05T22:11:21+00:00

This patch contains fixes identified by checkpatch when run with the
strict option.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

amd-xgbe-phy: Enhance parallel detection to support KR speed

2014-09-05T22:11:20+00:00

Add support to allow parallel detection to work in KR speed. With
both speed modes of KX and KR supported, KX must be checked first.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

amd-xgbe-phy: Check device for current speed mode (KR/KX)

2014-09-05T22:11:20+00:00

Since device resets can change the current mode it's possible to think
the device is in a different mode than it actually is.  Rather than
trying to determine every place that is needed to set/save the current
mode, be safe and check the devices actual mode when needed rather than
trying to track it.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

amd-xgbe-phy: Allow more time for Rx/Tx to become ready

2014-08-03T02:29:53+00:00

The current time range waiting for Rx/Tx to become ready can sometimes
be too short if a connection is not present.  Increase the number of
retries and the sleep to give a bit more time. Also, change level of
the message issued from _err to _dbg if Rx/Tx do not become ready
since the underlying logic will function as if no link is established
and retry eventually.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

amd-xgbe-phy: Print out the auto-negotiation method used

2014-07-31T01:46:53+00:00

Add a netdev_info statement detailing whether auto-negotiation was
completed through parallel detection or through the auto-negotiation
protocol.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

amd-xgbe-phy: Updates to KR training initiation

2014-07-31T01:46:53+00:00

As part of changing rates to KR mode, KR training is initiated. If
the KR training is restarted it is possible to enter an invalid logic
state. This can be avoided by asserting a training reset bit before
initiating the KR training and then clearing the training reset bit.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

amd-xgbe-phy: Updates to rate change complete check

2014-07-31T01:46:53+00:00

Currently, the logic will loop endlessly waiting for a rate change
to complete.  Add a counter so that if the rate change signals
never indicate complete the loop will eventually exit.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller