A number of PHYs support the PHY tunable to set and get
downshift. However, only 88E1116R enables downshift by default. Extend
this default enabled to all the PHYs that support the downshift
tunable.

Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add downshift support for 88E1240, it uses the same downshift
configuration registers as 88E1011.

Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20210428095356.621536-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There is no real need for disabling autonigotiation in config_init().
Leave it enabled by default.

Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added .config_intr and .handle_interrupt callbacks.

Link event interrupt will trigger an interrupt every time when the link
goes up or down.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing downshift params without software reset has no effect,
so call genphy_soft_reset() after change downshift params.

As the datasheet says:
Changes to these bits are disruptive to the normal operation therefore,
any changes to these registers must be followed by software reset
to take effect.

Fixes: 5c6bc5199b5d ("net: phy: marvell: add downshift support for M88E1111")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing downshift params without software reset has no effect,
so call genphy_soft_reset() after change downshift params.

As the datasheet says:
Changes to these bits are disruptive to the normal operation therefore,
any changes to these registers must be followed by software reset
to take effect.

Fixes: 911af5e149bb ("net: phy: marvell: fix downshift function naming")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This causes error reported by kernel test robot.

Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 41d26bf4aba0 ("net: phy: marvell: refactor HWMON OOP style")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Intel xway phys offer the possibility to deactivate the integrated
LED function and to control the LEDs manually.
If this was set by the bootloader, it must be ensured that the
integrated LED function is enabled for all LEDs when loading the driver.

Before commit 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
the LEDs were enabled by a soft-reset of the PHY (using
genphy_soft_reset). Initialize the XWAY_MDIO_LED with it's default
value (which is applied during a soft reset) instead of adding back
the soft reset. This brings back the default LED configuration while
still preventing an excessive amount of soft resets.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit c329e5afb42f ("net: phy: at803x: select correct page on
config init") selects the copper page during probe. This fails if the
copper page was already selected. In this case, the value of the copper
page (which is 1) is propagated through phy_restore_page() and is
finally returned for at803x_probe(). Fix it, by just using the
at803x_page_write() directly.

Also in case of an error, the regulator is not disabled and leads to a
WARN_ON() when the probe fails. This couldn't happen before, because
at803x_parse_dt() was the last call in at803x_probe(). It is hard to
see, that the parse_dt() actually enables the regulator. Thus move the
regulator_enable() to the probe function and undo it in case of an
error.

Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>