* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
  PCI: update for owner removal from struct device_attribute
  PCI: Fix warnings when CONFIG_DMI unset
  PCI: Do not run NVidia quirks related to MSI with MSI disabled
  x86/PCI: use for_each_pci_dev()
  PCI: use for_each_pci_dev()
  PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
  PCI: export SMBIOS provided firmware instance and label to sysfs
  PCI: Allow read/write access to sysfs I/O port resources
  x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
  PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
  PCI: disable mmio during bar sizing
  PCI: MSI: Remove unsafe and unnecessary hardware access
  PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
  PCI: kernel oops on access to pci proc file while hot-removal
  PCI: pci-sysfs: remove casts from void*
  ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
  PCI hotplug: make sure child bridges are enabled at hotplug time
  PCI hotplug: shpchp: Removed check for hotplug of display devices
  PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
  PCI: Don't enable aspm before drivers have had a chance to veto it
  ...

This patch (as1388) changes the way the PCI core handles runtime PM
settings when probing or unbinding drivers.  Now the core will make
sure the device is enabled for runtime PM, with a usage count >= 1,
when a driver is probed.  It does the same when calling a driver's
remove method.

If the driver wants to use runtime PM, all it has to do is call
pm_runtime_pu_noidle() near the end of its probe routine (to cancel
the core's usage increment) and pm_runtime_get_noresume() near the
start of its remove routine (to restore the usage count).  It does not
need to mess around with setting the runtime state to enabled,
disabled, active, or suspended.

The patch updates e1000e and r8169, the only PCI drivers that already
use the existing runtime PM interface.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Conflicts:
	drivers/vhost/net.c
	net/bridge/br_device.c

Fix merge conflict in drivers/vhost/net.c with guidance from
Stephen Rothwell.

Revert the effects of net-2.6 commit 573201f36fd9c7c6d5218cdcd9948cee700b277d
since net-next-2.6 has fixes that make bridge netpoll work properly thus
we don't need it disabled.

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge error.

See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.

Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/sfc/net_driver.h
	drivers/net/sfc/siena.c

Some configurations need delay between the "write completed" indication
and new write to work reliably.

Realtek driver seems to use longer delay when polling the "write complete"
bit, so it waits long enough between writes with high probability (but
could probably break too). This patch adds a new udelay to make sure we
wait unconditionally some time after the write complete indication.

This caused a regression with XID 18000000 boards when the board specific
phy configuration writing many mdio registers was added in commit
2e955856ff (r8169: phy init for the 8169scd). Some of the configration
mdio writes would almost always fail, and depending on failure might leave
the PHY in non-working state.

Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

readl() returns a 32-bit integer on all platforms.
There is no need to cast its return value.

Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/e100.c
	drivers/net/e1000e/netdev.c