linux-toradex.git/drivers/net/tg3.c, branch v2.6.16.42

[TG3]: Fix array overrun in tg3_read_partno().

2006-11-19T23:12:55+00:00

Use proper upper limits for the loops and check for all error
conditions.

The problem was noticed by Adrian Bunk.

Signed-off-by: Michael Chan 
Signed-off-by: Adrian Bunk

[PATCH] TG3: ethtool always report port is TP.

2006-05-20T22:00:31+00:00

Even with fiber cards ethtool reports that the connected port is TP,
the patch fix this.

Signed-off-by: Karsten Keil 
Acked-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Chris Wright 
Signed-off-by: Greg Kroah-Hartman

[TG3]: 40-bit DMA workaround part 2

2006-03-19T21:21:12+00:00

The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.

For example, some 4-port card or mother board designs have 5704 behind
the 5714.

All devices behind the EPB require the 40-bit DMA workaround.

Thanks to Chris Elmquist again for reporting the problem and testing
the patch.

Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller

[TG3] tg3_bus_string(): remove dead code

2006-03-12T02:49:38+00:00

The Coverity checker spotted this dead code (note that (clock_ctrl == 7) 
is already handled above).

Signed-off-by: Adrian Bunk 
Signed-off-by: David S. Miller

[TG3]: Add DMA address workaround

2006-03-07T03:28:35+00:00

Add DMA workaround for chips that do not support full 64-bit DMA
addresses.

5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().

5788 only supports 32-bit DMA so need to set the mask appropriately
also.

Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.

Thanks to David Miller for explaining the HIGHMEM and DMA stuff.

Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller

[TG3]: Fix Sun tg3 variant detection.

2006-02-27T20:51:27+00:00

Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem
vendor ID.  So add another fallback test, which is the name
of the OBP firmware device tree node.  If it's a Sun part we'll
get "network", else it will be named "ethernet".

Signed-off-by: David S. Miller

[TG3]: Update driver version and release date.

2006-02-03T01:29:59+00:00

Signed-off-by: David S. Miller

[TG3]: Flush tg3_reset_task()

2006-02-03T01:29:28+00:00

Make sure tg3_reset_task() is flushed in the close and suspend paths
as noted by Jeff Garzik.

In the close path, calling flush_scheduled_work() may cause deadlock
if linkwatch_event() is on the workqueue. linkwatch_event() will try
to get the rtnl_lock() which is already held by tg3_close(). So
instead, we set a flag in tg3_reset_task() and tg3_close() polls
the flag until it is cleared.

Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller

[TG3]: Refine nvram locking

2006-01-17T10:40:55+00:00

Add nvram lock count so that calls to tg3_nvram_lock()/unlock() can
be nested. Add error checking to all callers of tg3_nvram_lock()
where appropriate. To prevent nvram lock failures after halting the
firmware, it is also necessary to release firmware's nvram lock in
tg3_halt_cpu().

Update version to 3.48.

Based on David Miller's initial patch.

Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller

[TG3]: fixup tot_len calculation

2006-01-03T22:19:25+00:00

Turning struct iphdr::tot_len into __be16 added sparse warning.

Signed-off-by: Alexey Dobriyan 
Signed-off-by: David S. Miller