The Belkin B2B128 is a USB 3.0 Hub + Gigabit Ethernet Adapter, the
Ethernet adapter uses the ASIX AX88179 USB 3.0 to Gigabit Ethernet
chip supported by this driver, add the USB ID for the same.

This patch is based on work by Geoffrey Tran <geoffrey.tran@gmail.com>
who has indicated they would like this upstreamed by someone more
familiar with the upstreaming process.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.

Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Getting the device version out of the driver really aids debugging.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Network devices can allocate reasources and private memory using
netdev_ops->ndo_init().  However, the release of these resources
can occur in one of two different places.

Either netdev_ops->ndo_uninit() or netdev->destructor().

The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.

netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.

netdev->destructor(), on the other hand, does not run until the
netdev references all go away.

Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().

This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.

If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit().  But
it is not able to invoke netdev->destructor().

This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.

However, this means that the resources that would normally be released
by netdev->destructor() will not be.

Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.

Many drivers do not try to deal with this, and instead we have leaks.

Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().

netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().

netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().

Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().

And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().

Signed-off-by: David S. Miller <davem@davemloft.net>

Some devices need their multicast filter reset but others are crashed by that.
So the methods need to be separated.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: "Ridgway, Keith" <kridgway@harris.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When TX checksum offload is used, if the computed checksum is 0 the
LAN95xx device do not alter the checksum to 0xffff.  In the case of ipv4
UDP checksum, it indicates to receiver that no checksum is calculated.
Under ipv6, UDP checksum yields a result of zero must be changed to
0xffff. Hence disabling checksum offload for ipv6 packets.

Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>

Reported-by: popcorn mix <popcornmix@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use a new USB device ID for the wwan modules in
their 2017 laptops.  The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing endianness conversions to a debug statement printing
the USB device-descriptor idVendor and idProduct fields during probe.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The zero padding that is added to NTB's does
not zero the memory correctly.
This is because the skb_put modifies the value
of skb_out->len which results in the memset
command not setting any memory to zero as
(ctx->tx_max - skb_out->len) == 0.

I have resolved this by storing the size of
the memory to be zeroed before the skb_put
and using this in the memset call.

Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for Telit ME910 PID 0x1100.

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>