linux-toradex.git/drivers/net/wireless/intel, branch v4.9.119

iwlwifi: pcie: fix race in Rx buffer allocator

2018-08-03T05:55:15+00:00

[ Upstream commit 0f22e40053bd5378ad1e3250e65c574fd61c0cd6 ]

Make sure the rx_allocator worker is canceled before running the
rx_init routine.  rx_init frees and re-allocates all rxb's pages.  The
rx_allocator worker also allocates pages for the used rxb's.  Running
rx_init and rx_allocator simultaniously causes a kernel panic.  Fix
that by canceling the work in rx_init.

Signed-off-by: Shaul Triebitz 
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: pcie: compare with number of IRQs requested for, not number of CPUs

2018-06-26T00:08:05+00:00

[ Upstream commit ab1068d6866e28bf6427ceaea681a381e5870a4a ]

When there are 16 or more logical CPUs, we request for
`IWL_MAX_RX_HW_QUEUES` (16) IRQs only as we limit to that number of
IRQs, but later on we compare the number of IRQs returned to
nr_online_cpus+2 instead of max_irqs, the latter being what we
actually asked for. This ends up setting num_rx_queues to 17 which
causes lots of out-of-bounds array accesses later on.

Compare to max_irqs instead, and also add an assertion in case
num_rx_queues > IWM_MAX_RX_HW_QUEUES.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199551

Fixes: 2e5d4a8f61dc ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Hao Wei Tee 
Tested-by: Sara Sharon 
Signed-off-by: Luca Coelho 
Signed-off-by: Kalle Valo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: fix TX of CCMP 256

2018-05-30T05:50:34+00:00

[ Upstream commit de04d4fbf87b769ab18c480e4f020c53e74bbdd2 ]

We don't have enough room in the TX command for a CCMP 256
key, and need to use key from table.

Fixes: 3264bf032bd9 ("[BUGFIX] iwlwifi: mvm: Fix CCMP IV setting")
Signed-off-by: Sara Sharon 
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: always init rs with 20mhz bandwidth rates

2018-05-30T05:50:27+00:00

[ Upstream commit 6b7a5aea71b342ec0593d23b08383e1f33da4c9a ]

In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.

Signed-off-by: Naftali Goldstein 
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: fix security bug in PN checking

2018-05-30T05:50:27+00:00

[ Upstream commit 5ab2ba931255d8bf03009c06d58dce97de32797c ]

A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.

This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.

Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.

Fixes: f1ae02b186d9 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU")
Signed-off-by: Sara Sharon 
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: fix min API version for 7265D, 3168, 8000 and 8265

2018-04-13T17:48:21+00:00

[ Upstream commit 15098803d38778070b8edfa5a3d5fc4fef10d0a1 ]

In a previous commit, we removed support for API versions earlier than
22 for these NICs.  By mistake, the *_UCODE_API_MIN definitions were
set to 17.  Fix that.

Fixes: 4b87e5af638b ("iwlwifi: remove support for fw older than -17 and -22")
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: pcie: only use d0i3 in suspend/resume if system_pm is set to d0i3

2018-04-13T17:48:21+00:00

[ Upstream commit e4c49c4937951de1cdbe35572ade40c948dec1e1 ]

We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791

Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: tt: move ucode_loaded check under mutex

2018-04-13T17:48:20+00:00

[ Upstream commit d9954405758a0cbbe258d9b4d4dc12a06fa48a28 ]

The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.

Fixes: 5c89e7bc557e ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Johannes Berg 
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: Fix command queue number on d0i3 flow

2018-04-13T17:48:20+00:00

[ Upstream commit c72c37b7f392ad7edc10b6092fa48c632ba6f4ed ]

During d0i3 flow we flush all the queue except from the command queue.
Currently, in this flow the command queue is hard coded to 9.
In DQA the command queue number has changed from 9 to 0.
Fix that.

This fixes a problem in runtime PM resume flow.

Fixes: 097129c9e625 ("iwlwifi: mvm: move cmd queue to be #0 in dqa mode")
Signed-off-by: Haim Dreyfuss 
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iwlwifi: mvm: fix firmware debug restart recording

2018-04-13T17:48:20+00:00

[ Upstream commit addce854f164a68da9cb158e2e7e447705068549 ]

When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.

Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
  recording)

For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.

Signed-off-by: Emmanuel Grumbach 
Signed-off-by: Luca Coelho 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman