Debug prints enabled inadvertently in smsc usb code being disabled

Bug 703116

Change-Id: I80e36ffd1ea845ac46cedd17c0fe67d983e18ffa
Reviewed-on: http://git-master.nvidia.com/r/3885
Reviewed-by: Bitan Biswas <bbiswas@nvidia.com>
Tested-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Narendra Damahe <ndamahe@nvidia.com>
Reviewed-by: Antti Rasmus <arasmus@nvidia.com>
Reviewed-by: Gary King <gking@nvidia.com>

ccf5b801c changed uintf.pm_usage_cnt to an atomic_t; update this driver
to reflect the change

bug 696988
Change-Id: If587ca9c98a7f92f35a0143283c6d13a862c3d6e
Reviewed-on: http://git-master/r/2336
Reviewed-by: Gary King <gking@nvidia.com>
Tested-by: Gary King <gking@nvidia.com>

Bug 693439

Change-Id: Id251d6be11e1b251c45e811173ba770683f11c48
Reviewed-by: Narendra Damahe <ndamahe@nvidia.com>
Tested-by: Narendra Damahe <ndamahe@nvidia.com>
Reviewed-by: Gary King <gking@nvidia.com>

commit 098dfded5b1b09927995e89c6d689f85a0f53384 upstream.

iwl_set_rxon_ht() only get called in iwl_post_associate(); which cause
possible incorrect ht configuration. Adding the call in iwl_mac_config() if
IEEE80211_CONF_CHANGE_CHANNEL flag is set to re-configure and send rxon
command.

Fixes
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2146

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit 6c8afef551fef87a3bf24f8a74c69a7f2f72fc82 upstream.

Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.

Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit b6c3f5be7c6ac3375f44de4545c1ffe216b34022 upstream.

Commit c7ab5ef9bcd281135c21b4732c9be779585181be entitled "b43: implement
short slot and basic rate handling" reduced the transmit throughput for
my BCM4311 device from 18 Mb/s to 0.7 Mb/s. The basic rate handling
portion is OK, the problem is in the short slot handling.

Prior to this change, the short slot enable/disable routines were never
called. Experimentation showed that the critical part was changing the
value at offset 0x0010 in the shared memory. This is supposed to contain
the 802.11 Slot Time in usec, but if it is changed from its initial value
of zero, performance is destroyed. On the other hand, changing the value
in the MMIO register corresponding to the Interframe Slot Time increased
performance from 18 to 22 Mb/s. A BCM4306/3 also shows dramatic
improvement of the transmit rate from 5.3 to 19.0 Mb/s.

Other changes in the patch include removal of the magic number for the
MMIO register, and allowing the slot time to be set for any PHY operating
in the 2.4 GHz band. Previously, the routine was executed only for G PHYs.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit 174b24963eaf96dc5e093502ee09639aed13eb2f upstream.

Add new RTL8187B device.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit 74401773f80b6d42f7a4c6994ca0cca883b03745 upstream.

When cleaning up beacon buffers and slots, ath9k currently checks if
sc->ah->opmode is set to a beacon related mode before cleaning up
buffers.
An unfortunate ordering of interface up/down commands can lead to
sc->ah->opmode being set to monitor mode, while there are AP interfaces
present on the same wiphy.
Always cleaning up beacon buffers if present fixes this issue.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit aa8bc9ef18a2c5b2b97e1f36ee9604cf15743f96 upstream.

Among other changes, this commit:

   commit 06d0f0663e11cab4ec5f2c143a118d71a12fbbe9
   Author: Sujith <Sujith.Manoharan@atheros.com>
   Date:   Thu Feb 12 10:06:45 2009 +0530

   ath9k: Enable Fractional N mode

changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.

According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Jorge Boncompte <jorge@dti2.net>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>