linux-toradex.git/drivers/net, branch v4.1.20

can: ems_usb: Fix possible tx overflow

2016-03-07T17:33:23+00:00

[ Upstream commit 90cfde46586d2286488d8ed636929e936c0c9ab2 ]

This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.

Signed-off-by: Gerhard Uttenthaler 
Cc: linux-stable 
Signed-off-by: Marc Kleine-Budde 
Signed-off-by: Sasha Levin

iwlwifi: mvm: don't allow sched scans without matches to be started

2016-03-07T17:23:16+00:00

[ Upstream commit 5e56276e7555b34550d51459a801ff75eca8b907 ]

The firmware can perform a scheduled scan with not matchsets passed,
but it can't send notification that results were found.  Since the
userspace then cannot know when we got new results and the firmware
wouldn't trigger a wake in case we are sleeping, it's better not to
allow scans without matchsets.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=110831

Cc:  [3.17+]
Signed-off-by: Luca Coelho 
Signed-off-by: Emmanuel Grumbach 
[SL: Backport to 4.1]
Signed-off-by: Sasha Levin

pppoe: fix reference counting in PPPoE proxy

2016-03-04T15:25:51+00:00

[ Upstream commit 29e73269aa4d36f92b35610c25f8b01c789b0dc8 ]

Drop reference on the relay_po socket when __pppoe_xmit() succeeds.
This is already handled correctly in the error path.

Signed-off-by: Guillaume Nault 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net/mlx4_en: Avoid changing dev->features directly in run-time

2016-03-04T15:25:51+00:00

[ Upstream commit 925ab1aa9394bbaeac47ee5b65d3fdf0fb8135cf ]

It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.

Fixes: f4a1edd56120 ('net/mlx4_en: Advertize encapsulation offloads [...]')
Signed-off-by: Eugenia Emantayev 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net/mlx4_en: Choose time-stamping shift value according to HW frequency

2016-03-04T15:25:50+00:00

[ Upstream commit 31c128b66e5b28f468076e4f3ca3025c35342041 ]

Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.

Algorithm for shift value calculation:
 * Round up the maximal value in cycles to nearest power of two

 * Calculate maximal multiplier by division of all 64 bits set
   to above result

 * Then, invert the function clocksource_khz2mult() to get the shift from
   maximal mult value

Fixes: ec693d47010e ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev 
Reviewed-by: Matan Barak 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net/mlx4_en: Count HW buffer overrun only once

2016-03-04T15:25:50+00:00

[ Upstream commit 281e8b2fdf8e4ef366b899453cae50e09b577ada ]

RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.

Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.

Fix that. Use it for rx_fifo_errors only.

Fixes: c27a02cd94d6 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Amir Vadai 
Signed-off-by: Eugenia Emantayev 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

qmi_wwan: add "4G LTE usb-modem U901"

2016-03-04T15:25:50+00:00

[ Upstream commit aac8d3c282e024c344c5b86dc1eab7af88bb9716 ]

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Reported-by: Thomas Schäfer 
Signed-off-by: Bjørn Mork 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bonding: Fix ARP monitor validation

2016-03-04T15:25:50+00:00

[ Upstream commit 21a75f0915dde8674708b39abfcda113911c49b1 ]

The current logic in bond_arp_rcv will accept an incoming ARP for
validation if (a) the receiving slave is either "active" (which includes
the currently active slave, or the current ARP slave) or, (b) there is a
currently active slave, and it has received an ARP since it became active.
For case (b), the receiving slave isn't the currently active slave, and is
receiving the original broadcast ARP request, not an ARP reply from the
target.

	This logic can fail if there is no currently active slave.  In
this situation, the ARP probe logic cycles through all slaves, assigning
each in turn as the "current_arp_slave" for one arp_interval, then setting
that one as "active," and sending an ARP probe from that slave.  The
current logic expects the ARP reply to arrive on the sending
current_arp_slave, however, due to switch FDB updating delays, the reply
may be directed to another slave.

	This can arise if the bonding slaves and switch are working, but
the ARP target is not responding.  When the ARP target recovers, a
condition may result wherein the ARP target host replies faster than the
switch can update its forwarding table, causing each ARP reply to be sent
to the previous current_arp_slave.  This will never pass the logic in
bond_arp_rcv, as neither of the above conditions (a) or (b) are met.

	Some experimentation on a LAN shows ARP reply round trips in the
200 usec range, but my available switches never update their FDB in less
than 4000 usec.

	This patch changes the logic in bond_arp_rcv to additionally
accept an ARP reply for validation on any slave if there is a current ARP
slave and it sent an ARP probe during the previous arp_interval.

Fixes: aeea64ac717a ("bonding: don't trust arp requests unless active slave really works")
Cc: Veaceslav Falico 
Cc: Andy Gospodarek 
Signed-off-by: Jay Vosburgh 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs

2016-03-04T15:25:49+00:00

[ Upstream commit b7d987295c74500b733a0ba07f9a9bcc4074fa83 ]

tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.

tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.

This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.

v2: Corrected patch description to avoid confusion.

Signed-off-by: Siva Reddy Kallam 
Signed-off-by: Michael Chan 
Acked-by: Prashant Sreedharan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

switchdev: Require RTNL mutex to be held when sending FDB notifications

2016-03-04T15:25:47+00:00

[ Upstream commit 4f2c6ae5c64c353fb1b0425e4747e5603feadba1 ]

When switchdev drivers process FDB notifications from the underlying
device they resolve the netdev to which the entry points to and notify
the bridge using the switchdev notifier.

However, since the RTNL mutex is not held there is nothing preventing
the netdev from disappearing in the middle, which will cause
br_switchdev_event() to dereference a non-existing netdev.

Make switchdev drivers hold the lock at the beginning of the
notification processing session and release it once it ends, after
notifying the bridge.

Also, remove switchdev_mutex and fdb_lock, as they are no longer needed
when RTNL mutex is held.

Fixes: 03bf0c281234 ("switchdev: introduce switchdev notifier")
Signed-off-by: Ido Schimmel 
Signed-off-by: Jiri Pirko 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin