linux-toradex.git/drivers/net, branch v4.9.45

usb: qmi_wwan: add D-Link DWM-222 device ID

2017-08-25T00:12:21+00:00

commit bed9ff165960921303a100228585f2d1691b42eb upstream.

Signed-off-by: Hector Martin 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net/mlx4_en: don't set CHECKSUM_COMPLETE on SCTP packets

2017-08-13T02:31:22+00:00

[ Upstream commit e718fe450e616227b74d27a233cdf37b4df0c82b ]

if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.

V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set

Reported-by: Shuang Li 
Fixes: f8c6455bb04b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti 
Acked-by: Saeed Mahameed 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

ppp: fix xmit recursion detection on ppp channels

2017-08-13T02:31:21+00:00

[ Upstream commit 0a0e1a85c83775a648041be2b15de6d0a2f2b8eb ]

Commit e5dadc65f9e0 ("ppp: Fix false xmit recursion detect with two ppp
devices") dropped the xmit_recursion counter incrementation in
ppp_channel_push() and relied on ppp_xmit_process() for this task.
But __ppp_channel_push() can also send packets directly (using the
.start_xmit() channel callback), in which case the xmit_recursion
counter isn't incremented anymore. If such packets get routed back to
the parent ppp unit, ppp_xmit_process() won't notice the recursion and
will call ppp_channel_push() on the same channel, effectively creating
the deadlock situation that the xmit_recursion mechanism was supposed
to prevent.

This patch re-introduces the xmit_recursion counter incrementation in
ppp_channel_push(). Since the xmit_recursion variable is now part of
the parent ppp unit, incrementation is skipped if the channel doesn't
have any. This is fine because only packets routed through the parent
unit may enter the channel recursively.

Finally, we have to ensure that pch->ppp is not going to be modified
while executing ppp_channel_push(). Instead of taking this lock only
while calling ppp_xmit_process(), we now have to hold it for the full
ppp_channel_push() execution. This respects the ppp locks ordering
which requires locking ->upl before ->downl.

Fixes: e5dadc65f9e0 ("ppp: Fix false xmit recursion detect with two ppp devices")
Signed-off-by: Guillaume Nault 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

ppp: Fix false xmit recursion detect with two ppp devices

2017-08-13T02:31:21+00:00

[ Upstream commit e5dadc65f9e0177eb649bcd9d333f1ebf871223e ]

The global percpu variable ppp_xmit_recursion is used to detect the ppp
xmit recursion to avoid the deadlock, which is caused by one CPU tries to
lock the xmit lock twice. But it would report false recursion when one CPU
wants to send the skb from two different PPP devices, like one L2TP on the
PPPoE. It is a normal case actually.

Now use one percpu member of struct ppp instead of the gloable variable to
detect the xmit recursion of one ppp device.

Fixes: 55454a565836 ("ppp: avoid dealock on recursive xmit")
Signed-off-by: Gao Feng 
Signed-off-by: Liu Jianying 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: Fix PHY unbind crash

2017-08-11T15:49:37+00:00

commit 7b9a88a390dacb37b051a7b09b9a08f546edf5eb upstream.

The PHY library does not deal very well with bind and unbind events. The first
thing we would see is that we were not properly canceling the PHY state machine
workqueue, so we would be crashing while dereferencing phydev->drv since there
is no driver attached anymore.

Suggested-by: Russell King 
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Cc: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

net/mlx5: E-Switch, Re-enable RoCE on mode change only after FDB destroy

2017-08-11T15:49:36+00:00

[ Upstream commit 5bae8c031053c69b4aa74b7f1ba15d4ec8426208 ]

We must re-enable RoCE on the e-switch management port (PF) only after destroying
the FDB in its switchdev/offloaded mode. Otherwise, when encapsulation is supported,
this re-enablement will fail.

Also, it's more natural and symmetric to disable RoCE on the PF before we create
the FDB under switchdev mode, so do that as well and revert if getting into error
during the mode change later.

Fixes: 9da34cd34e85 ('net/mlx5: Disable RoCE on the e-switch management [..]')
Signed-off-by: Or Gerlitz 
Reviewed-by: Hadar Hen Zion 
Signed-off-by: Saeed Mahameed 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

phy state machine: failsafe leave invalid RUNNING state

2017-08-11T15:49:35+00:00

[ Upstream commit 811a919135b980bac8009d042acdccf10dc1ef5e ]

While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().

If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.

This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.

This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.

Signed-off-by: Zefir Kurtisi 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

tg3: Fix race condition in tg3_get_stats64().

2017-08-11T15:49:34+00:00

[ Upstream commit f5992b72ebe0dde488fa8f706b887194020c66fc ]

The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations.  Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block.  tg3_get_stats64() is
already taking tp->lock.

Reported-by: Wang Yufen 
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

net: phy: dp83867: fix irq generation

2017-08-11T15:49:34+00:00

[ Upstream commit 5ca7d1ca77dc23934504b95a96d2660d345f83c2 ]

For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.

Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.

Signed-off-by: Grygorii Strashko 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

sh_eth: R8A7740 supports packet shecksumming

2017-08-11T15:49:34+00:00

[ Upstream commit 0f1f9cbc04dbb3cc310f70a11cba0cf1f2109d9c ]

The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data,  thus CSMR isn't cleared...

Fixes: 73a0d907301e ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman