Add support for connectivity event

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The core st21nca module is useless without the I2C access module.
So hide NFC_ST21NFCA and select it automatically if either
NFC_ST21NFCA_I2C is selected.

This avoids presenting NFC_ST21NFCA when NFC_ST21NFCA_I2C can't be
selected.

Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

A few code cleanups, mostly empty lines removal.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add support for acpi probing.
SMO2100 is used for st21nfca

It has been tested with the following acpi node on Minnowboard Max:
Note: Remove uicc-present or ese-present Package if one them is not
supported.

Device (NFC1)
{
	Name (_ADR, Zero)  // _ADR: Address
	Name (_HID, "SMO2100")  // _HID: Hardware ID
	Name (_CID, "SMO2100")  // _CID: Compatible ID
	Name (_DDN, "SMO NFC")  // _DDN: DOS Device Name
	Name (_UID, One)  // _UID: Unique ID
	Name (_DSD, Package (0x02)
	{
		/* Device Properties for _DSD */
		ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
		Package (0x02)
		{
			Package (0x02) { "uicc-present", 1 },
			Package (0x02) { "ese-present", 1 }
		}
	})
	Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
	{
		Name (SBUF, ResourceTemplate ()
		{
			I2cSerialBus (0x0001, ControllerInitiated, 400000,
				      AddressingMode7Bit, "\\_SB.I2C7",
				      0x00, ResourceConsumer, ,)
			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
				 "\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0001
			}
			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
				"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
			{       // Pin list
				0x0002,
			}
		})
		Return (SBUF) /* \_SB_.I2C7.NFC1._CRS.SBUF */
	}
	Method (_STA, 0, NotSerialized)  // _STA: Status
	{
		Return (0x0F)
	}
}

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add macro definition for each gpio string for an easier code
maintenance.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Group device table at the same place in order to make the code
easier to read and parse.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

DT headers already define NOOP routines when CONFIG_OF is not
defined.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add support for proprietary commands useful mainly
for factory testings.

Here is a list:

- FACTORY_MODE: Allow to set the driver into a mode where no
  secure element are activated. It does not consider any
  NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
  command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry as
  for example RF trimmings or low level drivers configurations
  (I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
  CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
  low level drivers configurations or RF trimmings.
- HCI_DM_LOAD: Allow to load a firmware into the CLF. A complete
  packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
  configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
  the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
  technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
  connectivity.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Potentially an unexpected HCI event may occur because of a
firmware bug. It could be transparent for the user but we should
at least log it.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>