linux-toradex.git/drivers/pci, branch v3.13.9

PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled

2014-03-24T04:44:16+00:00

commit 3cdeb713dc66057b50682048c151eae07b186c42 upstream.

Andreas reported that after 1f42db786b14 ("PCI: Enable INTx if BIOS left
them disabled"), pciehp surprise removal stopped working.

This happens because pci_reenable_device() on the hotplug bridge (used in
the pciehp_configure_device() path) clears the Interrupt Disable bit, which
apparently breaks the bridge's MSI hotplug event reporting.

Previously we cleared the Interrupt Disable bit in do_pci_enable_device(),
which is used by both pci_enable_device() and pci_reenable_device().  But
we use pci_reenable_device() after the driver may have enabled MSI or
MSI-X, and we *set* Interrupt Disable as part of enabling MSI/MSI-X.

This patch clears Interrupt Disable only when MSI/MSI-X has not been
enabled.

Fixes: 1f42db786b14 PCI: Enable INTx if BIOS left them disabled
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71691
Reported-and-tested-by: Andreas Noever 
Signed-off-by: Bjorn Helgaas 
CC: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

PCI: Enable INTx if BIOS left them disabled

2014-03-07T06:06:22+00:00

commit 1f42db786b14a31bf807fc41ee5583a00c08fcb1 upstream.

Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts.  Clear Interrupt Disable so we get those interrupts.

Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.

Link: http://lkml.kernel.org/r/20140114181721.GC12126@xanatos
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70601
Reported-by: Chris Cheng 
Reported-and-tested-by: Jamie Chen 
Signed-off-by: Bjorn Helgaas 
CC: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

PCI: mvebu: Use Device ID and revision from underlying endpoint

2014-03-07T06:06:22+00:00

commit 322a8e91844f4ae2093e0d3d8a318d0ef2596756 upstream.

Marvell SoCs place the SoC number into the PCIe endpoint device ID.  The
SoC stepping is placed into the PCIe revision. The old plat-orion PCIe
driver allowed this information to be seen in user space with a simple
lspci command.

The new driver places a virtual PCI-PCI bridge on top of these endpoints.
It has its own hard coded PCI device ID. Thus it is no longer possible to
see what the SoC is using lspci.

When initializing the PCI-PCI bridge, set its device ID and revision from
the underlying endpoint, thus restoring this functionality.  Debian would
like to use this in order to aid installing the correct DTB file.

Fixes: 45361a4fe4464 ("pci: PCIe driver for Marvell Armada 370/XP systems")
Signed-off-by: Andrew Lunn 
Signed-off-by: Bjorn Helgaas 
Acked-by: Thomas Petazzoni 
Acked-by: Jason Cooper 
Signed-off-by: Greg Kroah-Hartman

ACPI / hotplug / PCI: Relax the checking of _STA return values

2014-02-22T21:34:57+00:00

commit 7282059489868e0ed1b0d79765730c6b233a8399 upstream.

The ACPI specification (ACPI 5.0A, Section 6.3.7) says:

 _STA may return bit 0 clear (not present) with bit 3 set (device is
 functional). This case is used to indicate a valid device for which
 no device driver should be loaded (for example, a bridge device.)
 Children of this device may be present and valid. OSPM should
 continue enumeration below a device whose _STA returns this bit
 combination.

Evidently, some BIOSes follow that and return 0x0A from _STA, which
causes problems to happen when they trigger bus check or device check
notifications for those devices too.  Namely, ACPIPHP thinks that they
are gone and may drop them, for example, if such a notification is
triggered during a resume from system suspend.

To fix that, modify ACPICA to regard devies as present and
functioning if _STA returns both the ACPI_STA_DEVICE_ENABLED
and ACPI_STA_DEVICE_FUNCTIONING bits set for them.

Reported-and-tested-by: Peter Wu 
[rjw: Subject and changelog, minor code modifications]
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

xen/pvhvm: If xen_platform_pci=0 is set don't blow up (v4).

2014-02-13T21:55:28+00:00

commit 51c71a3bbaca868043cc45b3ad3786dd48a90235 upstream.

The user has the option of disabling the platform driver:
00:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device (rev 01)

which is used to unplug the emulated drivers (IDE, Realtek 8169, etc)
and allow the PV drivers to take over. If the user wishes
to disable that they can set:

  xen_platform_pci=0
  (in the guest config file)

or
  xen_emul_unplug=never
  (on the Linux command line)

except it does not work properly. The PV drivers still try to
load and since the Xen platform driver is not run - and it
has not initialized the grant tables, most of the PV drivers
stumble upon:

input: Xen Virtual Keyboard as /devices/virtual/input/input5
input: Xen Virtual Pointer as /devices/virtual/input/input6M
------------[ cut here ]------------
kernel BUG at /home/konrad/ssd/konrad/linux/drivers/xen/grant-table.c:1206!
invalid opcode: 0000 [#1] SMP
Modules linked in: xen_kbdfront(+) xenfs xen_privcmd
CPU: 6 PID: 1389 Comm: modprobe Not tainted 3.13.0-rc1upstream-00021-ga6c892b-dirty #1
Hardware name: Xen HVM domU, BIOS 4.4-unstable 11/26/2013
RIP: 0010:[]  [] get_free_entries+0x2e0/0x300
Call Trace:
 [] ? evdev_connect+0x1e3/0x240
 [] gnttab_grant_foreign_access+0x2e/0x70
 [] xenkbd_connect_backend+0x41/0x290 [xen_kbdfront]
 [] xenkbd_probe+0x2f2/0x324 [xen_kbdfront]
 [] xenbus_dev_probe+0x77/0x130
 [] xenbus_frontend_dev_probe+0x47/0x50
 [] driver_probe_device+0x89/0x230
 [] __driver_attach+0x9b/0xa0
 [] ? driver_probe_device+0x230/0x230
 [] ? driver_probe_device+0x230/0x230
 [] bus_for_each_dev+0x8c/0xb0
 [] driver_attach+0x19/0x20
 [] bus_add_driver+0x1a0/0x220
 [] driver_register+0x5f/0xf0
 [] xenbus_register_driver_common+0x15/0x20
 [] xenbus_register_frontend+0x23/0x40
 [] ? 0xffffffffa0014fff
 [] xenkbd_init+0x2b/0x1000 [xen_kbdfront]
 [] do_one_initcall+0x49/0x170

.. snip..

which is hardly nice. This patch fixes this by having each
PV driver check for:
 - if running in PV, then it is fine to execute (as that is their
   native environment).
 - if running in HVM, check if user wanted 'xen_emul_unplug=never',
   in which case bail out and don't load any PV drivers.
 - if running in HVM, and if PCI device 5853:0001 (xen_platform_pci)
   does not exist, then bail out and not load PV drivers.
 - (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=ide-disks',
   then bail out for all PV devices _except_ the block one.
   Ditto for the network one ('nics').
 - (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=unnecessary'
   then load block PV driver, and also setup the legacy IDE paths.
   In (v3) make it actually load PV drivers.

Reported-by: Sander Eikelenboom 
Reported-and-Tested-by: Fabio Fantoni 
Signed-off-by: Konrad Rzeszutek Wilk 
[v2: Add extra logic to handle the myrid ways 'xen_emul_unplug'
can be used per Ian and Stefano suggestion]
[v3: Make the unnecessary case work properly]
[v4: s/disks/ide-disks/ spotted by Fabio]
Reviewed-by: Stefano Stabellini 
Acked-by: Bjorn Helgaas  [for PCI parts]
Signed-off-by: Greg Kroah-Hartman

Merge branches 'acpi-pci-pm' and 'acpi-pci-hotplug'

2013-12-31T21:03:37+00:00

* acpi-pci-pm:
  PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI

* acpi-pci-hotplug:
  ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
  ACPI / PCI / hotplug: Avoid warning when _ADR not present

ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug

2013-12-31T12:39:42+00:00

The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec).  Then, the system stops functioning correctly.

Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again.  For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.

Fixes: bbd34fcdd1b2 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian 
Reported-and-tested-by: 
Reported-and-tested-by: Joaquín Aramendía 
Cc: Alex Deucher 
Cc: Dave Airlie 
Cc: Takashi Iwai 
Signed-off-by: Rafael J. Wysocki 
Cc: 3.12+  # 3.12+

PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI

2013-12-29T22:37:15+00:00

It turns out that some BIOSes don't report wakeup GPEs through
_PRW, but use them for signaling wakeup anyway, which causes GPE
storms to occur on some systems after resume from system suspend.
This issue has been uncovered by commit d2e5f0c16ad6 (ACPI / PCI:
Rework the setup and cleanup of device wakeup) during the 3.9
development cycle.

Work around the problem by installing wakeup notify handlers for all
PCI devices with ACPI support (i.e. having ACPI companions) regardless
of whether or not the BIOS reports ACPI wakeup support for them.  The
presence of the wakeup notify handlers alone is not harmful in any
way if there are no events for them to handle (they are simply never
executed then), but on some systems they are needed to take care of
spurious events.

Fixes: d2e5f0c16ad6 (ACPI / PCI: Rework the setup and cleanup of device wakeup)
References: https://bugzilla.kernel.org/show_bug.cgi?id=63021
Reported-and-tested-by: Agustin Barto 
Cc: Bjorn Helgaas 
Signed-off-by: Rafael J. Wysocki

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2013-12-15T19:56:47+00:00

Pull networking fixes from David Miller:

 1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
    figure out why it breaks things.

 2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
    was basically doing "x == x", from Dave Jones.

 3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
    Sebastian Siewior.

 4) Blackhole and prohibit routes in ipv6 were not doing the right thing
    because their ->input and ->output methods were not being assigned
    correctly.  Now they behave properly like their ipv4 counterparts.
    From Kamala R.

 5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
    really do not support this feature and will send garbage packets if
    fed fraglist SKBs.  From Eric Dumazet.

 6) Fix long standing user triggerable BUG_ON over loopback in RDS
    protocol stack, from Venkat Venkatsubra.

 7) Several not so common code paths can potentially try to invoke
    packet scheduler actions that might be NULL without checking.  Shore
    things up by either 1) defining a method as mandatory and erroring
    on registration if that method is NULL 2) defininig a method as
    optional and the registration function hooks up a default
    implementation when NULL is seen.  From Jamal Hadi Salim.

 8) Fix fragment detection in xen-natback driver, from Paul Durrant.

 9) Kill dangling enter_memory_pressure method in cg_proto ops, from
    Eric W Biederman.

10) SKBs that traverse namespaces should have their local_df cleared,
    from Hannes Frederic Sowa.

11) IOCB file position is not being updated by macvtap_aio_read() and
    tun_chr_aio_read().  From Zhi Yong Wu.

12) Don't free virtio_net netdev before releasing all of the NAPI
    instances.  From Andrey Vagin.

13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.

14) IPv6 routes that are no cached routes should not count against the
    garbage collection limits.  We had this almost right, but were
    missing handling addrconf generated routes properly.  From Hannes
    Frederic Sowa.

15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
    route info when they are called, from Stefan Tomanek.

16) TUN and MACVTAP have had truncated packet signalling for some time,
    fix from Jason Wang.

17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.

18) xen-netback does not interpret the NAPI budget properly for TX work,
    fix from Paul Durrant.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
  igb: Fix for issue where values could be too high for udelay function.
  i40e: fix null dereference
  xen-netback: fix gso_prefix check
  net: make neigh_priv_len in struct net_device 16bit instead of 8bit
  drivers: net: cpsw: fix for cpsw crash when build as modules
  xen-netback: napi: don't prematurely request a tx event
  xen-netback: napi: fix abuse of budget
  sch_tbf: use do_div() for 64-bit divide
  udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
  net:fec: remove duplicate lines in comment about errata ERR006358
  Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
  8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
  xen-netback: make sure skb linear area covers checksum field
  net: smc91x: Fix device tree based configuration so it's usable
  udp: ipv4: fix potential use after free in udp_v4_early_demux()
  macvtap: signal truncated packets
  tun: unbreak truncated packet signalling
  net: sched: htb: fix the calculation of quantum
  net: sched: tbf: fix the calculation of max_size
  micrel: add support for KSZ8041RNLI
  ...

Merge tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

2013-12-15T19:45:27+00:00

Pull PCI updates from Bjorn Helgaas:
 "PCI device hotplug
    - Move device_del() from pci_stop_dev() to pci_destroy_dev() (Rafael
      Wysocki)

  Host bridge drivers
    - Update maintainers for DesignWare, i.MX6, Armada, R-Car (Bjorn
      Helgaas)
    - mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
      (Jason Gunthorpe)

  Miscellaneous
    - Avoid unnecessary CPU switch when calling .probe() (Alexander
      Duyck)
    - Revert "workqueue: allow work_on_cpu() to be called recursively"
      (Bjorn Helgaas)
    - Disable Bus Master only on kexec reboot (Khalid Aziz)
    - Omit PCI ID macro strings to shorten quirk names for LTO (Michal
      Marek)"

* tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  MAINTAINERS: Add DesignWare, i.MX6, Armada, R-Car PCI host maintainers
  PCI: Disable Bus Master only on kexec reboot
  PCI: mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
  PCI: Omit PCI ID macro strings to shorten quirk names
  PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev()
  Revert "workqueue: allow work_on_cpu() to be called recursively"
  PCI: Avoid unnecessary CPU switch when calling driver .probe() method