linux-toradex.git/drivers/phy/freescale/Kconfig, branch master

phy: fsl-imx8mq-usb: add tca function driver for imx95

2025-02-14T12:26:12+00:00

The i.MX95 USB3 phy has a Type-C Assist block (TCA). This block consists
two functional blocks (XBar assist and VBus assist) and one system
access interface using APB.

The primary functionality of XBar assist is:
 - switching lane for flip
 - moving unused lanes into lower power states.

This info can be get from:
i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.

This will add support for TCA block to achieve lane switching and tca
lower power functionality.

Signed-off-by: Xu Yang 
Reviewed-by: Jun Li 
Link: https://lore.kernel.org/r/20241204050907.1081781-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul

phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support

2024-06-15T12:22:01+00:00

Add i.MX8QM HSIO PHY driver support.

i.MX8QM HSIO has three lane PHY instances, and can be bound to the
following controllers in the different use cases listed in below table.
- two lanes capable PCIEA controller.
- one lane PCIEB controller.
- AHCI SATA controller.

i.MX8QM HSIO PHYs support the following use cases.
+----------------------------------------------------+
|                               | Lane0| Lane1| Lane2|
|-------------------------------|------|------|------|
| use case 1: PCIEAX2SATA       | PCIEA| PCIEA| SATA |
|-------------------------------|------|------|------|
| use case 2: PCIEAX2PCIEB      | PCIEA| PCIEA| PCIEB|
|-------------------------------|------|------|------|
| use case 3: PCIEAPCIEBSATA    | PCIEA| PCIEB| SATA |
+----------------------------------------------------+

Signed-off-by: Richard Zhu 
Reviewed-by: Frank Li 
Link: https://lore.kernel.org/r/1716962565-2084-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Vinod Koul

phy: freescale: add Samsung HDMI PHY

2024-03-28T18:57:06+00:00

This adds the driver for the Samsung HDMI PHY found on the
i.MX8MP SoC. Based on downstream implementation from
Sandor Yu .  According to the TRM, the PHY
receives parallel data from the link and serializes it.  It
also sets the PLL clock needed for the TX serializer.

Tested-by: Luca Ceresoli 
Tested-by: Richard Leitner 
Co-developed-by: Marco Felsch 
Signed-off-by: Marco Felsch 
Signed-off-by: Lucas Stach 
Tested-by: Alexander Stein 
Tested-by: Frieder Schrempf  # Kontron BL
Signed-off-by: Adam Ford 
Tested-by: Marek Vasut 
Tested-by: Luca Ceresoli 
Tested-by: Tommaso Merciai 
Link: https://lore.kernel.org/r/20240227220444.77566-3-aford173@gmail.com
Signed-off-by: Vinod Koul

phy: freescale: Add i.MX8qm Mixel LVDS PHY support

2022-07-08T05:13:20+00:00

Add Freescale i.MX8qm LVDS PHY support.
The PHY IP is from Mixel, Inc.

Signed-off-by: Liu Ying 
Link: https://lore.kernel.org/r/20220706034810.2352641-4-victor.liu@nxp.com
Signed-off-by: Vinod Koul

phy: PHY_FSL_LYNX_28G should depend on ARCH_LAYERSCAPE

2022-03-29T15:45:16+00:00

Freescale Layerscape Lynx 28G SerDes PHYs are only present on
Freescale/NXP Layerscape SoCs.

Move PHY_FSL_LYNX_28G outside the block for ARCH_MXC, as the latter
is meant for i.MX8 SoCs, which is a different family than Layerscape.
Add a dependency on ARCH_LAYERSCAPE, to prevent asking the user about
this driver when configuring a kernel without Layerscape SoC support.

Fixes: 02e2af20f4f9f2aa ("Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc")
Fixes: 8f73b37cf3fbda67 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Linus Torvalds

Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

2022-03-28T19:27:35+00:00

Pull char/misc and other driver updates from Greg KH:
 "Here is the big set of char/misc and other small driver subsystem
  updates for 5.18-rc1.

  Included in here are merges from driver subsystems which contain:

   - iio driver updates and new drivers

   - fsi driver updates

   - fpga driver updates

   - habanalabs driver updates and support for new hardware

   - soundwire driver updates and new drivers

   - phy driver updates and new drivers

   - coresight driver updates

   - icc driver updates

  Individual changes include:

   - mei driver updates

   - interconnect driver updates

   - new PECI driver subsystem added

   - vmci driver updates

   - lots of tiny misc/char driver updates

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
  firmware: google: Properly state IOMEM dependency
  kgdbts: fix return value of __setup handler
  firmware: sysfb: fix platform-device leak in error path
  firmware: stratix10-svc: add missing callback parameter on RSU
  arm64: dts: qcom: add non-secure domain property to fastrpc nodes
  misc: fastrpc: Add dma handle implementation
  misc: fastrpc: Add fdlist implementation
  misc: fastrpc: Add helper function to get list and page
  misc: fastrpc: Add support to secure memory map
  dt-bindings: misc: add fastrpc domain vmid property
  misc: fastrpc: check before loading process to the DSP
  misc: fastrpc: add secure domain support
  dt-bindings: misc: add property to support non-secure DSP
  misc: fastrpc: Add support to get DSP capabilities
  misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
  misc: fastrpc: separate fastrpc device from channel context
  dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
  dt-bindings: nvmem: make "reg" property optional
  nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
  nvmem: dt-bindings: Fix the error of dt-bindings check
  ...

phy: add support for the Layerscape SerDes 28G

2022-03-14T10:41:50+00:00

This patch adds a new generic PHY driver to support the Lynx 28G SerDes
block found on some of the Layerscape SoCs such as LX2160A.
At the moment, only the following Ethernet protocols are supported:
SGMII/1000Base-X and 10GBaseR.

SerDes lanes which are not running an Ethernet protocol or a currently
supported Ethenet protocol will be left as it was configured through the
RCW (Reset Configuration Word) at boot time.

At probe time, the platform driver will read the current
configuration of both PLLs found on a SerDes block and will determine
what protocols are supported using that PLL.

For example, if a PLL is configured to generate a clock net (frate) of
5GHz the only protocols sustained by that PLL are SGMII/1000Base-X
(using a quarter of the full clock rate) and QSGMII using the full clock
net frequency on the lane.

On the .set_mode() callback, the PHY driver will first check if the
requested operating mode (protocol) is even supported by the current PLL
configuration and will error out if not.
Then, the lane is reconfigured to run on the requested protocol.

Signed-off-by: Ioana Ciornei 
Signed-off-by: David S. Miller

phy: freescale: i.MX8 PHYs should depend on ARCH_MXC && ARM64

2022-01-27T05:35:18+00:00

The Freescale/NXP i.MX8 USB3, MIPI DSI, and PCIE PHYs are only present
on the NXP i.MX8 family of SoCs.  Hence wrap the config symbols for
these PHYs inside a check for ARCH_MXC && ARM64, to prevent asking the
user about these drivers when configuring a kernel without NXP i.MX SoC
family support.

Signed-off-by: Geert Uytterhoeven 
Reviewed-by: Guido Günther 
Link: https://lore.kernel.org/r/393868affd830016d35f0d9aba32ccd7098c8073.1641987369.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul

phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver

2021-12-14T14:32:53+00:00

Add the standalone i.MX8 PCIe PHY driver.

Signed-off-by: Richard Zhu 
Tested-by: Marcel Ziswiler 
Reviewed-by: Tim Harvey 
Tested-by: Tim Harvey 
Link: https://lore.kernel.org/r/1638432158-4119-6-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Vinod Koul

Merge tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

2019-07-01T13:04:59+00:00

phy: for 5.3

  *) Add a new PHY driver for Qualcomm PCIe2 PHY
  *) Add a new PHY driver for Mixel DPHY present in i.MX8
  *) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
     PHY enable failed
  *) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
     calling a sleeping function from invalid context
  *) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
     imbalance powered flag
  *) Fix .cocci and sparse warnings

Signed-off-by: Kishon Vijay Abraham I 

* tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
  phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay
  phy: meson-g12a-usb3-pcie: disable locking for cr_regmap
  phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs
  dt-bindings: phy: Add documentation for mixel dphy
  dt-bindings: phy-pxa-usb: add bindings
  phy: renesas: rcar-gen3-usb2: fix imbalance powered flag
  phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting
  phy: qcom-qmp: Correct READY_STATUS poll break condition
  phy: ti: am654-serdes: Make serdes_am654_xlate() static
  phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings
  phy: samsung: Use struct_size() in devm_kzalloc()
  phy: qcom: Add Qualcomm PCIe2 PHY driver
  dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY