linux-toradex.git/drivers/phy/rockchip, branch v6.17 Linux kernel for Apalis and Colibri modules phy: rockchip-pcie: Properly disable TEST_WRITE strobe signal 2025-07-22T12:28:45+00:00 Geraldo Nascimento geraldogabriel@gmail.com 2025-06-30T22:25:28+00:00 25facbabc3fc33c794ad09d73f73268c0f8cbc7d pcie_conf is used to touch TEST_WRITE strobe signal. This signal should be enabled, a little time waited, and then disabled. Current code clearly was copy-pasted and never disables the strobe signal. Adjust the define. While at it, remove PHY_CFG_RD_MASK which has been unused since 64cdc0360811 ("phy: rockchip-pcie: remove unused phy_rd_cfg function"). Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com> Link: https://lore.kernel.org/r/d514d5d5627680caafa8b7548cbdfee4307f5440.1751322015.git.geraldogabriel@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> 
pcie_conf is used to touch TEST_WRITE strobe signal. This signal should
be enabled, a little time waited, and then disabled. Current code clearly
was copy-pasted and never disables the strobe signal. Adjust the define.
While at it, remove PHY_CFG_RD_MASK which has been unused since
64cdc0360811 ("phy: rockchip-pcie: remove unused phy_rd_cfg function").

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/d514d5d5627680caafa8b7548cbdfee4307f5440.1751322015.git.geraldogabriel@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy: rockchip-pcie: Enable all four lanes if required 2025-07-22T12:28:44+00:00 Valmantas Paliksa walmis@gmail.com 2025-06-30T22:25:14+00:00 c3fe7071e196e25789ecf90dbc9e8491a98884d7 Current code enables only Lane 0 because pwr_cnt will be incremented on first call to the function. Let's reorder the enablement code to enable all 4 lanes through GRF. Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Valmantas Paliksa <walmis@gmail.com> Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/16b610aab34e069fd31d9f57260c10df2a968f80.1751322015.git.geraldogabriel@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> 
Current code enables only Lane 0 because pwr_cnt will be incremented on
first call to the function. Let's reorder the enablement code to enable
all 4 lanes through GRF.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>

Signed-off-by: Valmantas Paliksa <walmis@gmail.com>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/16b610aab34e069fd31d9f57260c10df2a968f80.1751322015.git.geraldogabriel@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merge tag 'phy-for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy 2025-06-05T15:20:21+00:00 Linus Torvalds torvalds@linux-foundation.org 2025-06-05T15:20:21+00:00 d12ed2b7e1fe5c9e4a372a95fb7635a7f81eff6a Pull phy updates from Vinod Koul: "As usual featuring couple of new driver and bunch of new device support and some driver changes to Freescale, rockchip driver along with couple of yaml binding conversions. New Support: - Qualcomm IPQ5424 qusb2 support, IPQ5018 uniphy-pcie driver - Rockchip usb2 support for RK3562, RK3036 usb2 phy support - Samsung exynos2200 eusb2 phy support and driver refactoring for this support, exynos7870 USBDRD support - Mediatek MT7988 xs-phy support - Broadcom BCM74110 usb phy support - Renesas RZ/V2H(P) usb2 phy support Updates: - Freescale phy rate claculation updates, i.MX95 tuning support - Better error handling for amlogic pcie phy - Rockchip color depth configuration and management support - Yaml binding conversion for RK3399 Type-C and PCIe Phy" * tag 'phy-for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (77 commits) phy: tegra: p2u: Broaden architecture dependency phy: rockchip: inno-usb2: Add usb2 phy support for rk3562 dt-bindings: phy: rockchip,inno-usb2phy: add rk3562 phy: rockchip: inno-usb2: add phy definition for rk3036 dt-bindings: phy: rockchip,inno-usb2phy: add rk3036 compatible phy: freescale: fsl-samsung-hdmi: Improve LUT search for best clock phy: freescale: fsl-samsung-hdmi: Refactor finding PHY settings phy: freescale: fsl-samsung-hdmi: Rename phy_clk_round_rate phy: renesas: phy-rcar-gen3-usb2: Add USB2.0 PHY support for RZ/V2H(P) phy: renesas: phy-rcar-gen3-usb2: Sort compatible entries by SoC part number dt-bindings: phy: renesas,usb2-phy: Document RZ/V2H(P) SoC dt-bindings: phy: renesas,usb2-phy: Add clock constraint for RZ/G2L family phy: exynos5-usbdrd: support Exynos USBDRD 3.2 4nm controller phy: phy-snps-eusb2: add support for exynos2200 phy: phy-snps-eusb2: refactor reference clock init phy: phy-snps-eusb2: make reset control optional phy: phy-snps-eusb2: make repeater optional phy: phy-snps-eusb2: split phy init code phy: phy-snps-eusb2: refactor constructs names phy: move phy-qcom-snps-eusb2 out of its vendor sub-directory ... 
Pull phy updates from Vinod Koul:
 "As usual featuring couple of new driver and bunch of new device
  support and some driver changes to Freescale, rockchip driver along
  with couple of yaml binding conversions.

  New Support:
   - Qualcomm IPQ5424 qusb2 support, IPQ5018 uniphy-pcie driver
   - Rockchip usb2 support for RK3562, RK3036 usb2 phy support
   - Samsung exynos2200 eusb2 phy support and driver refactoring for
     this support, exynos7870 USBDRD support
   - Mediatek MT7988 xs-phy support
   - Broadcom BCM74110 usb phy support
   - Renesas RZ/V2H(P) usb2 phy support

  Updates:
   - Freescale phy rate claculation updates, i.MX95 tuning support
   - Better error handling for amlogic pcie phy
   - Rockchip color depth configuration and management support
   - Yaml binding conversion for RK3399 Type-C and PCIe Phy"

* tag 'phy-for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (77 commits)
  phy: tegra: p2u: Broaden architecture dependency
  phy: rockchip: inno-usb2: Add usb2 phy support for rk3562
  dt-bindings: phy: rockchip,inno-usb2phy: add rk3562
  phy: rockchip: inno-usb2: add phy definition for rk3036
  dt-bindings: phy: rockchip,inno-usb2phy: add rk3036 compatible
  phy: freescale: fsl-samsung-hdmi: Improve LUT search for best clock
  phy: freescale: fsl-samsung-hdmi: Refactor finding PHY settings
  phy: freescale: fsl-samsung-hdmi: Rename phy_clk_round_rate
  phy: renesas: phy-rcar-gen3-usb2: Add USB2.0 PHY support for RZ/V2H(P)
  phy: renesas: phy-rcar-gen3-usb2: Sort compatible entries by SoC part number
  dt-bindings: phy: renesas,usb2-phy: Document RZ/V2H(P) SoC
  dt-bindings: phy: renesas,usb2-phy: Add clock constraint for RZ/G2L family
  phy: exynos5-usbdrd: support Exynos USBDRD 3.2 4nm controller
  phy: phy-snps-eusb2: add support for exynos2200
  phy: phy-snps-eusb2: refactor reference clock init
  phy: phy-snps-eusb2: make reset control optional
  phy: phy-snps-eusb2: make repeater optional
  phy: phy-snps-eusb2: split phy init code
  phy: phy-snps-eusb2: refactor constructs names
  phy: move phy-qcom-snps-eusb2 out of its vendor sub-directory
  ...
phy: rockchip: inno-usb2: Add usb2 phy support for rk3562 2025-05-14T11:20:39+00:00 Frank Wang frank.wang@rock-chips.com 2025-04-15T05:00:05+00:00 80edd21db00c0829c276baafa8871ae02c6e9d91 RK3652 has one USB2.0 PHY with two ports, the OTG port support OTG and BC1.2, the SoC provide USB GRF and APB to access the registers. This adds vbus detection function control and make the below tuning to enhance the usb2-phy SQ for RK3562 SoC. - enable pre-emphasis during non-chirp phase - set HS eye height to 425mv Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Signed-off-by: William Wu <william.wu@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20250415050005.52773-2-kever.yang@rock-chips.com Signed-off-by: Vinod Koul <vkoul@kernel.org> 
RK3652 has one USB2.0 PHY with two ports, the OTG port support OTG
and BC1.2, the SoC provide USB GRF and APB to access the registers.

This adds vbus detection function control and make the below tuning
to enhance the usb2-phy SQ for RK3562 SoC.
 - enable pre-emphasis during non-chirp phase
 - set HS eye height to 425mv

Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250415050005.52773-2-kever.yang@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy: rockchip: inno-usb2: add phy definition for rk3036 2025-05-14T11:19:29+00:00 Heiko Stuebner heiko@sntech.de 2025-05-03T20:15:11+00:00 3ca48b955bb34a3b07dd915318d73a23740de282 The usb2phy on rk3036 is very similar to rk3128 but not 100% identical. While most registers and bits are the same, a small fraction did get moved around. So we can re-use the phy-tuning function, but need a new set a bits. The biggest change might be that the phy on rk3036 does not support the charger detection, that rk3128 (and newer phys) have. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20250503201512.991277-3-heiko@sntech.de Signed-off-by: Vinod Koul <vkoul@kernel.org> 
The usb2phy on rk3036 is very similar to rk3128 but not 100% identical.
While most registers and bits are the same, a small fraction did get moved
around.

So we can re-use the phy-tuning function, but need a new set a bits.
The biggest change might be that the phy on rk3036 does not support the
charger detection, that rk3128 (and newer phys) have.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250503201512.991277-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy: phy-rockchip-samsung-hdptx: Fix PHY PLL output 50.25MHz error 2025-05-14T08:55:09+00:00 Algea Cao algea.cao@rock-chips.com 2025-04-27T09:51:24+00:00 f9475055b11c0c70979bd1667a76b2ebae638eb7 When using HDMI PLL frequency division coefficient at 50.25MHz that is calculated by rk_hdptx_phy_clk_pll_calc(), it fails to get PHY LANE lock. Although the calculated values are within the allowable range of PHY PLL configuration. In order to fix the PHY LANE lock error and provide the expected 50.25MHz output, manually compute the required PHY PLL frequency division coefficient and add it to ropll_tmds_cfg configuration table. Signed-off-by: Algea Cao <algea.cao@rock-chips.com> Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20250427095124.3354439-1-algea.cao@rock-chips.com Signed-off-by: Vinod Koul <vkoul@kernel.org> 
When using HDMI PLL frequency division coefficient at 50.25MHz
that is calculated by rk_hdptx_phy_clk_pll_calc(), it fails to
get PHY LANE lock. Although the calculated values are within the
allowable range of PHY PLL configuration.

In order to fix the PHY LANE lock error and provide the expected
50.25MHz output, manually compute the required PHY PLL frequency
division coefficient and add it to ropll_tmds_cfg configuration
table.

Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250427095124.3354439-1-algea.cao@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy: rockchip: samsung-hdptx: Remove unneeded semicolon 2025-05-14T08:30:08+00:00 Chen Ni nichen@iscas.ac.cn 2025-04-15T08:12:00+00:00 3b2b414927dcbd866c99ec92e3a214a69fc51c90 Remove unnecessary semicolons reported by Coccinelle/coccicheck and the semantic patch at scripts/coccinelle/misc/semicolon.cocci. Signed-off-by: Chen Ni <nichen@iscas.ac.cn> Link: https://lore.kernel.org/r/20250415081200.349939-1-nichen@iscas.ac.cn Signed-off-by: Vinod Koul <vkoul@kernel.org> 
Remove unnecessary semicolons reported by Coccinelle/coccicheck and the
semantic patch at scripts/coccinelle/misc/semicolon.cocci.

Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20250415081200.349939-1-nichen@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy: rockchip: samsung-hdptx: Add high color depth management 2025-04-11T11:48:04+00:00 Cristian Ciocaltea cristian.ciocaltea@collabora.com 2025-03-18T12:35:48+00:00 9d0ec51d7c227c3ae837e22832eaed219e25f126 Add support for 8-bit, 10-bit, 12-bit and 16-bit color depth setup. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Dmitry Baryshkov <dmtiry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-14-8cb1678e7663@collabora.com Signed-off-by: Vinod Koul <vkoul@kernel.org> 
Add support for 8-bit, 10-bit, 12-bit and 16-bit color depth setup.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmtiry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-14-8cb1678e7663@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy: rockchip: samsung-hdptx: Optimize internal rate handling 2025-04-11T11:48:04+00:00 Cristian Ciocaltea cristian.ciocaltea@collabora.com 2025-03-18T12:35:47+00:00 45b14bdcf4acfd483d9890396197c35c23821124 Drop the rate parameter from a bunch of internal helpers and, instead, make better use of the newly introduced ->hdmi_cfg.tmds_char_rate driver data. Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-13-8cb1678e7663@collabora.com Signed-off-by: Vinod Koul <vkoul@kernel.org> 
Drop the rate parameter from a bunch of internal helpers and, instead,
make better use of the newly introduced ->hdmi_cfg.tmds_char_rate driver
data.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-13-8cb1678e7663@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy: rockchip: samsung-hdptx: Rename ambiguous rk_hdptx_phy->rate 2025-04-11T11:48:04+00:00 Cristian Ciocaltea cristian.ciocaltea@collabora.com 2025-03-18T12:35:46+00:00 37f335dbfd028c008d0a7940ca5a270d1e2f6b81 The main purpose of the ->rate member of struct rk_hdptx_phy is to implement rk_hdptx_phy_clk_recalc_rate() by providing the actual rate programmed in hardware. Hence the current naming is too generic and rather ambiguous. Improve clarity by renaming ->rate to ->hw_rate. Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-12-8cb1678e7663@collabora.com Signed-off-by: Vinod Koul <vkoul@kernel.org> 
The main purpose of the ->rate member of struct rk_hdptx_phy is to
implement rk_hdptx_phy_clk_recalc_rate() by providing the actual rate
programmed in hardware.  Hence the current naming is too generic and
rather ambiguous.

Improve clarity by renaming ->rate to ->hw_rate.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-12-8cb1678e7663@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>