linux-toradex.git/drivers/phy/ti, branch v6.17

phy: ti: gmii-sel: Always write the RGMII ID setting

2025-09-01T16:30:58+00:00

Some SoCs are just validated with the TX delay enabled. With commit
ca13b249f291 ("net: ethernet: ti: am65-cpsw: fixup PHY mode for fixed
RGMII TX delay"), the network driver will patch the delay setting on the
fly assuming that the TX delay setting is fixed. In reality, the TX
delay is configurable and just skipped in the documentation. There are
bootloaders, which will disable the TX delay and this will lead to a
transmit path which doesn't add any delays at all.
Fix that by always writing the RGMII_ID setting and report an error for
unsupported RGMII delay modes.

This is safe to do and shouldn't break any boards in mainline because
the fixed delay is only introduced for gmii-sel compatibles which are
used together with the am65-cpsw-nuss driver and also contains the
commit above.

Fixes: ca13b249f291 ("net: ethernet: ti: am65-cpsw: fixup PHY mode for fixed RGMII TX delay")
Signed-off-by: Michael Walle 
Reviewed-by: Maxime Chevallier 
Link: https://lore.kernel.org/r/20250819065622.1019537-1-mwalle@kernel.org
Signed-off-by: Vinod Koul

phy: ti-pipe3: fix device leak at unbind

2025-08-12T16:00:00+00:00

Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.

Fixes: 918ee0d21ba4 ("usb: phy: omap-usb3: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org	# 3.13
Cc: Roger Quadros 
Signed-off-by: Johan Hovold 
Link: https://lore.kernel.org/r/20250724131206.2211-4-johan@kernel.org
Signed-off-by: Vinod Koul

phy: ti: omap-usb2: fix device leak at unbind

2025-08-12T16:00:00+00:00

Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.

Fixes: 478b6c7436c2 ("usb: phy: omap-usb2: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org	# 3.13
Cc: Roger Quadros 
Signed-off-by: Johan Hovold 
Link: https://lore.kernel.org/r/20250724131206.2211-3-johan@kernel.org
Signed-off-by: Vinod Koul

phy: drop probe registration printks

2025-06-16T17:24:21+00:00

Drivers should generally be quiet on successful probe, but this is not
followed by some PHY drivers, for example:

	snps-eusb2-hsphy 88e1000.phy: Registered Snps-eUSB2 phy
	qcom-eusb2-repeater c432000.spmi:pmic@7:phy@fd00: Registered Qcom-eUSB2 repeater
	qcom-eusb2-repeater c432000.spmi:pmic@a:phy@fd00: Registered Qcom-eUSB2 repeater
	qcom-eusb2-repeater c432000.spmi:pmic@b:phy@fd00: Registered Qcom-eUSB2 repeater
	snps-eusb2-hsphy fd3000.phy: Registered Snps-eUSB2 phy
	snps-eusb2-hsphy fd9000.phy: Registered Snps-eUSB2 phy
	snps-eusb2-hsphy fde000.phy: Registered Snps-eUSB2 phy
	snps-eusb2-hsphy 88e0000.phy: Registered Snps-eUSB2 phy
	snps-eusb2-hsphy 88e2000.phy: Registered Snps-eUSB2 phy

Drop (or demote to debug level) unnecessary registration info messages
to make boot logs a little less noisy.

Signed-off-by: Johan Hovold 
Link: https://lore.kernel.org/r/20250523085112.11287-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul

phy: ti: gmii-sel: Do not use syscon helper to build regmap

2025-02-14T12:30:01+00:00

The syscon helper device_node_to_regmap() is used to fetch a regmap
registered to a device node. It also currently creates this regmap
if the node did not already have a regmap associated with it. This
should only be used on "syscon" nodes. This driver is not such a
device and instead uses device_node_to_regmap() on its own node as
a hacky way to create a regmap for itself.

This will not work going forward and so we should create our regmap
the normal way by defining our regmap_config, fetching our memory
resource, then using the normal regmap_init_mmio() function.

Signed-off-by: Andrew Davis 
Tested-by: Nishanth Menon 
Link: https://lore.kernel.org/r/20250123182234.597665-1-afd@ti.com
Signed-off-by: Vinod Koul

Merge tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy

2024-11-27T21:33:43+00:00

Pull phy updates from Vinod Koul:
 "New hardware support:

   - ST STM32MP25 combophy support

   - Sparx5 support for lan969x serdes and updates to driver to support
     this

   - NXP PTN3222 eUSB2 to USB2 redriver

   - Qualcomm SAR2130P eusb2 support, QCS8300 USB DW3 and QMP USB2
     support, X1E80100 QMP PCIe PHY Gen4 support, QCS615 and QCS8300 QMP
     UFS PHY support and SA8775P eDP PHY support

   - Rockchip rk3576 usbdp and rk3576 usb2 phy support

   - Binding for Microchip ATA6561 can phy

  Updates:

   - Freescale driver updates from hdmi support

   - Conversion of rockchip rk3228 hdmi phy binding to yaml

   - Broadcom usb2-phy deprecated support dropped and USB init array
     update for BCM4908

   - TI USXGMII mode support in J7200

   - Switch back to platform_driver::remove() subsystem update"

* tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (59 commits)
  phy: qcom: qmp: Fix lecacy-legacy typo
  phy: lan969x-serdes: add support for lan969x serdes driver
  dt-bindings: phy: sparx5: document lan969x
  phy: sparx5-serdes: add support for branching on chip type
  phy: sparx5-serdes: add indirection layer to register macros
  phy: sparx5-serdes: add function for getting the CMU index
  phy: sparx5-serdes: add ops to match data
  phy: sparx5-serdes: add constant for the number of CMU's
  phy: sparx5-serdes: add constants to match data
  phy: sparx5-serdes: add support for private match data
  phy: bcm-ns-usb2: drop support for old binding variant
  dt-bindings: phy: bcm-ns-usb2-phy: drop deprecated variant
  dt-bindings: phy: Add QMP UFS PHY compatible for QCS8300
  dt-bindings: phy: qcom: snps-eusb2: Add SAR2130P compatible
  dt-bindings: phy: ti,tcan104x-can: Document Microchip ATA6561
  phy: airoha: Fix REG_CSR_2L_RX{0,1}_REV0 definitions
  phy: airoha: Fix REG_CSR_2L_JCPLL_SDM_HREN config in airoha_pcie_phy_init_ssc_jcpll()
  phy: airoha: Fix REG_PCIE_PMA_TX_RESET config in airoha_pcie_phy_init_csr_2l()
  phy: airoha: Fix REG_CSR_2L_PLL_CMN_RESERVE0 config in airoha_pcie_phy_init_clk_out()
  phy: phy-rockchip-samsung-hdptx: Don't request RST_PHY/RST_ROPLL/RST_LCPLL
  ...

phy: Switch back to struct platform_driver::remove()

2024-10-17T15:03:03+00:00

After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.

Convert all platform drivers below drivers/phy/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.

While touching these files, make indention of the struct initializer
consistent in several files.

Signed-off-by: Uwe Kleine-König 
Link: https://lore.kernel.org/r/20241009065307.504930-2-u.kleine-koenig@baylibre.com
Signed-off-by: Vinod Koul

phy: ti: phy-j721e-wiz: fix usxgmii configuration

2024-10-17T14:53:02+00:00

Commit b64a85fb8f53 ("phy: ti: phy-j721e-wiz.c: Add usxgmii support in
wiz driver") added support for USXGMII mode. In doing so, P0_REFCLK_SEL
was set to "pcs_mac_clk_divx1_ln_0" (0x3) and P0_STANDARD_MODE was set to
LANE_MODE_GEN1, which results in a data rate of 5.15625 Gbps. However,
since the USXGMII mode can support up to 10.3125 Gbps data rate, the
aforementioned fields should be set to "pcs_mac_clk_divx0_ln_0" (0x2) and
LANE_MODE_GEN2 respectively. The signal corresponding to the USXGMII lane
of the SERDES has been measured as 5 Gbps without the change and 10 Gbps
with the change. Hence, fix the configuration accordingly to support
USXGMII up to 10G.

Fixes: b64a85fb8f53 ("phy: ti: phy-j721e-wiz.c: Add usxgmii support in wiz driver")
Signed-off-by: Siddharth Vadapalli 
Reviewed-by: Roger Quadros 
Link: https://lore.kernel.org/r/20241012053937.3596885-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul

phy: ti: gmii-sel: Enable USXGMII mode for J7200

2024-10-11T08:29:44+00:00

TI's J7200 SoC supports USXGMII mode with the CPSW5G instance's MAC Port1.
Add USXGMII mode to the extra_modes member of J7200's SoC data.

Signed-off-by: Siddharth Vadapalli 
Reviewed-by: Roger Quadros 
Link: https://lore.kernel.org/r/20241010144845.2555983-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul

Merge tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy

2024-09-23T21:05:10+00:00

Pull phy updates from Vinod Koul:
 "New hw support:
   - Rcar usb2 support for RZ/G3S SoC
   - Nuvoton MA35 SoC USB 2.0 PHY driver

  Removed:
   - obsolete qcom,usb-8x16-phy bindings

  Updates:
   - 4 lane PCIe support for Qualcomm X1E80100
   - Constify structure in subsystem update
   - Subsystem simplification with scoped for each OF child loop update
   - Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
     bindings"

* tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (40 commits)
  phy: renesas: rcar-gen3-usb2: Add support for the RZ/G3S SoC
  dt-bindings: phy: renesas,usb2-phy: Document RZ/G3S phy bindings
  phy: renesas: rcar-gen3-usb2: Add support to initialize the bus
  phy: ti: j721e-wiz: Simplify with scoped for each OF child loop
  phy: ti: j721e-wiz: Drop OF node reference earlier for simpler code
  phy: ti: gmii-sel: Simplify with dev_err_probe()
  phy: ti: am654-serdes: Use scoped device node handling to simplify error paths
  phy: qcom: qmp-pcie-msm8996: Simplify with scoped for each OF child loop
  phy: mediatek: xsphy: Simplify with scoped for each OF child loop
  phy: mediatek: tphy: Simplify with scoped for each OF child loop
  phy: hisilicon: usb2: Simplify with scoped for each OF child loop
  phy: cadence: sierra: Simplify with scoped for each OF child loop
  phy: broadcom: brcm-sata: Simplify with scoped for each OF child loop
  phy: broadcom: bcm-cygnus-pcie: Simplify with scoped for each OF child loop
  phy: nuvoton: add new driver for the Nuvoton MA35 SoC USB 2.0 PHY
  dt-bindings: phy: nuvoton,ma35-usb2-phy: add new bindings
  phy: qcom: qmp-pcie: Configure all tables on port B PHY
  phy: airoha: adjust initialization delay in airoha_pcie_phy_init()
  dt-bindings: phy: socionext,uniphier: add top-level constraints
  phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100
  ...