Pull GPIO changes from Linus Walleij:
 "This is the bulk of GPIO changes for the v3.18 development cycle:

   - Increase the default ARCH_NR_GPIO from 256 to 512.  This was done
     to avoid having a custom <asm/gpio.h> header for the x86
     architecture - GPIO is custom and complicated enough as it is
     already! We want to move to a radix to store the descriptors going
     forward, and finally get rid of this fixed array size altogether.

   - Endgame patching of the gpio_remove() semantics initiated by
     Abdoulaye Berthe.  It is not accepted by the system that the
     removal of a GPIO chip fails during eg reboot or shutdown, and
     therefore the return value has now painfully been refactored away.
     For special cases like GPIO expanders on a hot-pluggable bus like
     USB, we may later add some gpiochip_try_remove() call, but for the
     cases we have now, return values are moot.

   - Some incremental refactoring of the gpiolib core and ACPI GPIO
     library for more descriptor usage.

   - Refactor the chained IRQ handler set-up method to handle also
     threaded, nested interrupts and set up the parent IRQ correctly.
     Switch STMPE and TC3589x drivers to use this registration method.

   - Add a .irq_not_threaded flag to the struct gpio_chip, so that also
     GPIO expanders that block but are still not using threaded IRQ
     handlers.

   - New drivers for the ARM64 X-Gene SoC GPIO controller.

   - The syscon GPIO driver has been improved to handle the "DSP GPIO"
     found on the TI Keystone 2 SoC:s.

   - ADNP driver switched to use gpiolib irqchip helpers.

   - Refactor the DWAPB driver to support being instantiated from and
     MFD cell (platform device).

   - Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
     Xilinx and Crystalcove drivers.

   - Various minor fixes"

* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
  gpio: pch: Build context save/restore only for PM
  pinctrl: abx500: get rid of unused variable
  gpio: ks8695: fix 'else should follow close brace '}''
  gpio: stmpe: add verbose debug code
  gpio: stmpe: fix up interrupt enable logic
  gpio: staticize xway_stp_init()
  gpio: handle also nested irqchips in the chained handler set-up
  gpio: set parent irq on chained handlers
  gpiolib: irqchip: use irq_find_mapping while removing irqchip
  gpio: crystalcove: support virtual GPIO
  pinctrl: bcm281xx: make Kconfig dependency more strict
  gpio: kona: enable only on BCM_MOBILE or for compile testing
  gpio, bcm-kona, LLVMLinux: Remove use of __initconst
  gpio: Fix ngpio in gpio-xilinx driver
  gpio: dwapb: fix pointer to integer cast
  gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
  gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
  gpio: xgene: Fix missing spin_lock_init()
  gpio: ks8695: fix switch case indentation
  gpiolib: add irq_not_threaded flag to gpio_chip
  ...

Some drivers accidentally still use the return value from
gpiochip_remove(). Get rid of them so we can simplify this function
and get rid of the return value.

Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

we have done that for atlas6 in commit ed36c1a, 086b8904 etc. here we
do same things for prima2.

Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch releases gpiochip related resources by calling
gpiochip_remove when gpiochip_irqchip_add fails.

CC: Linus Walleij <linus.walleij@linaro.org>
CC: Barry Song <Baohua.Song@csr.com>
CC: Rongjun Ying <rongjun.ying@csr.com>
CC: Yuping Luo <yuping.luo@csr.com>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

commit 2243a87d90b42eb38bc281957df3e57c712b5e56
"pinctrl: avoid duplicated calling enable_pinmux_setting for a pin"
removed the .disable callback from the struct pinmux_ops,
making the .enable() callback the only remaining callback.

However .enable() is a bad name as it seems to imply that a
muxing can also be disabled. Rename the callback to .set_mux()
and also take this opportunity to clean out any remaining
mentions of .disable() from the documentation.

Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Fan Wu <fwu@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The I2S controller can use the external clock as reference clock with
master mode. But based on different hardware or software design, this
external clock might be needed or not needed.
So the external input pin can be an independent pinctrl group, and the
card driver can decice to get it or not.

Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The I2S controller can output mclk to external audio codec. But by
hardware design, some codecs need mclk and some codecs do not need
mclk. So the mclk pin can be an independent pinctrl group, and the
card driver can get it or not based on boards.

Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

According to key customer's requirement, fix "line over 80
characters".

Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

this patch fixes:
WARNING: quoted string split across lines
902: FILE: drivers/pinctrl/sirf/pinctrl-sirf.c:902:
+MODULE_AUTHOR("Rongjun Ying <rongjun.ying@csr.com>, "
+	"Yuping Luo <yuping.luo@csr.com>, "

WARNING: quoted string split across lines
903: FILE: drivers/pinctrl/sirf/pinctrl-sirf.c:903:
+	"Yuping Luo <yuping.luo@csr.com>, "
+	"Barry Song <baohua.song@csr.com>");

Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

What the patch does:
1. Call pinmux_disable_setting ahead of pinmux_enable_setting
  each time pinctrl_select_state is called
2. Remove the HW disable operation in pinmux_disable_setting function.
3. Remove the disable ops in struct pinmux_ops
4. Remove all the disable ops users in current code base.

Notes:
1. Great thanks for the suggestion from Linus, Tony Lindgren and
   Stephen Warren and Everyone that shared comments on this patch.
2. The patch also includes comment fixes from Stephen Warren.

The reason why we do this:
1. To avoid duplicated calling of the enable_setting operation
   without disabling operation inbetween which will let the pin
   descriptor desc->mux_usecount increase monotonously.
2. The HW pin disable operation is not useful for any of the
   existing platforms.
   And this can be used to avoid the HW glitch after using the
   item #1 modification.

In the following case, the issue can be reproduced:
1. There is a driver that need to switch pin state dynamically,
   e.g. between "sleep" and "default" state
2. The pin setting configuration in a DTS node may be like this:

  component a {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&a_grp_setting &c_grp_setting>;
	pinctrl-1 = <&b_grp_setting &c_grp_setting>;
  }

  The "c_grp_setting" config node is totally identical, maybe like
  following one:

  c_grp_setting: c_grp_setting {
	pinctrl-single,pins = <GPIO48 AF6>;
  }

3. When switching the pin state in the following official pinctrl
   sequence:
	pin = pinctrl_get();
	state = pinctrl_lookup_state(wanted_state);
	pinctrl_select_state(state);
	pinctrl_put();

Test Result:
1. The switch is completed as expected, that is: the device's
   pin configuration is changed according to the description in the
   "wanted_state" group setting
2. The "desc->mux_usecount" of the corresponding pins in "c_group"
   is increased without being decreased, because the "desc" is for
   each physical pin while the setting is for each setting node
   in the DTS.
   Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead
   of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount
   will keep increasing without any chance to be decreased.

According to the comments in the original code, only the setting,
in old state but not in new state, will be "disabled" (calling
pinmux_disable_setting), which is correct logic but not intact. We
still need consider case that the setting is in both old state
and new state. We can do this in the following two ways:

1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin
   setting" repeatedly
2. "Disable"(calling pinmux_disable_setting) the "same pin setting",
   actually two setting instances, ahead of enabling them.

Analysis:
1. The solution #2 is better because it can avoid too much
   iteration.
2. If we disable all of the settings in the old state and one of
   the setting(s) exist in the new state, the pins mux function
   change may happen when some SoC vendors defined the
   "pinctrl-single,function-off"
   in their DTS file.
   old_setting => disabled_setting => new_setting.
3. In the pinmux framework, when a pin state is switched, the
   setting in the old state should be marked as "disabled".

Conclusion:
1. To Remove the HW disabling operation to above the glitch mentioned
   above.
2. Handle the issue mentioned above by disabling all of the settings
   in old state and then enable the all of the settings in new state.

Signed-off-by: Fan Wu <fwu@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>