Pull pincontrol updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.1 development
  cycle.  Nothing really exciting this time: we basically added a few
  new drivers and subdrivers and stabilized them in linux-next.  Some
  cleanups too.  With sunrisepoint Intel has a real fine fully featured
  pin control driver for contemporary hardware, and the AMD driver is
  also for large deployments.  Most of the others are ARM devices.

  New drivers:
    - Intel Sunrisepoint
    - AMD KERNCZ GPIO
    - Broadcom Cygnus IOMUX

  New subdrivers:
    - Marvell MVEBU Armada 39x SoCs
    - Samsung Exynos 5433
    - nVidia Tegra 210
    - Mediatek MT8135
    - Mediatek MT8173
    - AMLogic Meson8b
    - Qualcomm PM8916

  On top of this cleanups and development history for the above drivers
  as issues were fixed after merging"

* tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (71 commits)
  pinctrl: sirf: move sgpio lock into state container
  pinctrl: Add support for PM8916 GPIO's and MPP's
  pinctrl: bcm2835: Fix support for threaded level triggered IRQs
  sh-pfc: r8a7790: add EtherAVB pin groups
  pinctrl: Document "function" + "pins" pinmux binding
  pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support
  pinctrl: fsl: imx: Check for 0 config register
  pinctrl: Add support for Meson8b
  documentation: Extend pinctrl docs for Meson8b
  pinctrl: Cleanup Meson8 driver
  Fix inconsistent spinlock of AMD GPIO driver which can be recognized by static analysis tool smatch. Declare constant Variables with Sparse's suggestion.
  pinctrl: at91: convert __raw to endian agnostic IO
  pinctrl: constify of_device_id array
  pinctrl: pinconf-generic: add dt node names to error messages
  pinctrl: pinconf-generic: scan also referenced phandle node
  pinctrl: mvebu: add suspend/resume support to Armada XP pinctrl driver
  pinctrl: st: Display pin's function when printing pinctrl debug information
  pinctrl: st: Show correct pin direction also in GPIO mode
  pinctrl: st: Supply a GPIO get_direction() call-back
  pinctrl: st: Move st_get_pio_control() further up the source file
  ...

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

On sun4i-a10, when GPIOs are configured as external interrupt the value for
them in the data register does not seem to get updated, so set their mux to
input (and restore afterwards) when reading the pin.

Missed edges seem to be buffered, so this does not introduce a race
condition.

I've also tested this on sun5i-a13 and sun7i-a20 and those do not seem to
be affected, the input value representation in the data register does seem
to correctly get updated to the actual pin value while in irq mode there.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The A31s is a stripped down version of the A31, as such it is missing some
pins and some functions on some pins.

The new pinctrl-sun6i-a31s.c this commit adds is a copy of pinctrl-sun6i-a31s.c
with the missing pins and functions removed.

Note there is no a31s specific version of pinctrl-sun6i-a31-r.c, as the
prcm pins are identical between the A31 and the A31s.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

While working on pinctrl for the A31s, I noticed that function 4 of
PA15 - PA18 was missing, add these.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull driver core update from Greg KH:
 "Here's the set of driver core patches for 3.19-rc1.

  They are dominated by the removal of the .owner field in platform
  drivers.  They touch a lot of files, but they are "simple" changes,
  just removing a line in a structure.

  Other than that, a few minor driver core and debugfs changes.  There
  are some ath9k patches coming in through this tree that have been
  acked by the wireless maintainers as they relied on the debugfs
  changes.

  Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
  Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
  fs: debugfs: add forward declaration for struct device type
  firmware class: Deletion of an unnecessary check before the function call "vunmap"
  firmware loader: fix hung task warning dump
  devcoredump: provide a one-way disable function
  device: Add dev_<level>_once variants
  ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
  ath: use seq_file api for ath9k debugfs files
  debugfs: add helper function to create device related seq_file
  drivers/base: cacheinfo: remove noisy error boot message
  Revert "core: platform: add warning if driver has no owner"
  drivers: base: support cpu cache information interface to userspace via sysfs
  drivers: base: add cpu_device_create to support per-cpu devices
  topology: replace custom attribute macros with standard DEVICE_ATTR*
  cpumask: factor out show_cpumap into separate helper function
  driver core: Fix unbalanced device reference in drivers_probe
  driver core: fix race with userland in device_add()
  sysfs/kernfs: make read requests on pre-alloc files use the buffer.
  sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
  fs: sysfs: return EGBIG on write if offset is larger than file size
  ...

Pull take two of the GPIO updates:
 "Same stuff as last time, now with a fixup patch for the previous
  compile error plus I ran a few extra rounds of compile-testing.

  This is the bulk of GPIO changes for the v3.19 series:

   - A new API that allows setting more than one GPIO at the time.  This
     is implemented for the new descriptor-based API only and makes it
     possible to e.g. toggle a clock and data line at the same time, if
     the hardware can do this with a single register write.  Both
     consumers and drivers need new calls, and the core will fall back
     to driving individual lines where needed.  Implemented for the
     MPC8xxx driver initially

   - Patched the mdio-mux-gpio and the serial mctrl driver that drives
     modems to use the new multiple-setting API to set several signals
     simultaneously

   - Get rid of the global GPIO descriptor array, and instead allocate
     descriptors dynamically for each GPIO on a certain GPIO chip.  This
     moves us closer to getting rid of the limitation of using the
     global, static GPIO numberspace

   - New driver and device tree bindings for 74xx ICs

   - New driver and device tree bindings for the VF610 Vybrid

   - Support the RCAR r8a7793 and r8a7794

   - Guidelines for GPIO device tree bindings trying to get things a bit
     more strict with the advent of combined device properties

   - Suspend/resume support for the MVEBU driver

   - A slew of minor fixes and improvements"

* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
  gpio: mcp23s08: fix up compilation error
  gpio: pl061: document gpio-ranges property for bindings file
  gpio: pl061: hook request if gpio-ranges avaiable
  gpio: mcp23s08: Add option to configure IRQ output polarity as active high
  gpio: fix deferred probe detection for legacy API
  serial: mctrl_gpio: use gpiod_set_array function
  mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
  gpio: remove const modifier from gpiod_get_direction()
  gpio: remove gpio_descs global array
  gpio: mxs: implement get_direction callback
  gpio: em: Use dynamic allocation of GPIOs
  gpio: Check if base is positive before calling gpio_is_valid()
  gpio: mcp23s08: Add simple IRQ support for SPI devices
  gpio: mcp23s08: request a shared interrupt
  gpio: mcp23s08: Do not free unrequested interrupt
  gpio: rcar: Add r8a7793 and r8a7794 support
  gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
  gpiolib: allow simultaneous setting of multiple GPIO outputs
  gpio: mvebu: add suspend/resume support
  gpio: gpio-davinci: remove duplicate check on resource
  ..

The A80 has a rather usual pin controller, the only thing out of the ordinary
being that it has 5 interrupts banks, and that some pins have several options
for the same functions.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The A80 R-PIO controller has one more bank that what we've seen so far, add the
PN pin bank.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>