commit 486095fae3a8a6b1ae07c51844699d9bd5cfbebc upstream.

PG8, PG9 is said to be the CTS/RTS pins for UART1 according to the A23/33
datasheets. However, the function is wrongly named "uart2" in the pinctrl
driver. This patch fixes this by modifying them to be named "uart1".

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5e7515ba78fff2f5407eaa2f97c1d5c07801ac3d upstream.

pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.

However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.

Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.

This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull GPIO updates from Linus Walleij:
 "Here is the bulk of GPIO changes for the v4.4 development cycle.

  The only changes hitting outside drivers/gpio are in the pin control
  subsystem and these seem to have settled nicely in linux-next.

  Development mistakes and catfights are nicely documented in the
  reverts as you can see.  The outcome of the ABI fight is that we're
  working on a chardev ABI for GPIO now, where hope to show results for
  the v4.5 kernel.

  Summary of changes:

  GPIO core:
   - Define and handle flags for open drain/open collector and open
     source/open emitter, also know as "single-ended" configurations.
   - Generic request/free operations that handle calling out to the
     (optional) pin control backend.
   - Some refactoring related to an ABI change that did not happen, yet
     provide useful.
   - Added a real-time compliance checklist.  Many GPIO chips have
     irqchips, and need to think this over with the RT patches going
     upstream.
   - Restructure, fix and clean up Kconfig menus a bit.

  New drivers:
   - New driver for AMD Promony.
   - New driver for ACCES 104-IDIO-16, a port-mapped I/O card,
     ISA-style.  Very retro.

  Subdriver changes:
   - OMAP changes to handle real time requirements.
   - Handle trigger types for edge and level IRQs on PL061 properly.  As
     this hardware is very common it needs to set a proper example for
     others to follow.
   - Some container_of() cleanups.
   - Delete the unused MSM driver in favor of the driver that is
     embedded inside the pin control driver.
   - Cleanup of the ath79 GPIO driver used by many, many OpenWRT router
     targets.
   - A consolidated IT87xx driver replacing the earlier very specific
     IT8761e driver.
   - Handle the TI TCA9539 in the PCA953x driver.  Also handle ACPI
     devices in this subdriver.
   - Drop xilinx arch dependencies as these FPGAs seem to profilate over
     a few different architectures.  MIPS and ARM come to mind"

* tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (57 commits)
  gpio: fix up SPI submenu
  gpio: drop surplus I2C dependencies
  gpio: drop surplus X86 dependencies
  gpio: dt-bindings: document the official use of "ngpios"
  gpio: MAINTAINERS: Add an entry for the ATH79 GPIO driver
  gpio / ACPI: Allow shared GPIO event to be read via operation region
  gpio: group port-mapped I/O drivers in a menu
  gpio: Add ACCES 104-IDIO-16 driver maintainer entry
  gpio: zynq: Document interrupt-controller DT binding
  gpio: xilinx: Drop architecture dependencies
  gpio: generic: Revert to old error handling in bgpio_map
  gpio: add a real time compliance notes
  Revert "gpio: add a real time compliance checklist"
  gpio: Add GPIO support for the ACCES 104-IDIO-16
  gpio: driver for AMD Promontory
  gpio: xlp: Convert to use gpiolib irqchip helpers
  gpio: add a real time compliance checklist
  gpio/xilinx: enable for MIPS
  gpiolib: Add and use OF_GPIO_SINGLE_ENDED flag
  gpiolib: Split GPIO flags parsing and GPIO configuration
  ...

Pull pin control updates from Linus Walleij:
 "This is the big bulk of pin control changes for the v4.4 kernel
  development cycle.  Development pace is high in pin control again this
  merge window.  28 contributors, 83 patches.

  It hits a few sites outside the pin control subsystem:

   - Device tree bindings in Documentation (as usual)
   - MAINTAINERS
   - drivers/base/* for the "init" state handling by Doug Anderson.
     This has been ACKed by Greg.
   - drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
     in the USB subsystem.  This has been ACKed by both Greg and Felipe.
   - arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
     through the ARM SoC tree but ended up here.

  This time I am using Geert Uytterhoeven as submaintainer for SH PFC
  since the are three-four people working in parallel with new Renesas
  ASICs.

  Summary of changes:

  Infrastructure:

   - Doug Anderson wrote a patch adding an "init" state different from
     the "default" state for pin control state handling in the core
     framework.  This is applied before the driver's probe() call if
     defined and takes precedence over "default".  If both are defined,
     "init" will be applied *before* probe() and "default" will be
     applied *after* probe().

  Significant subdriver improvements:

   - SH PFC is switched to getting GPIO ranges from the device tree
     ranges property on DT platforms.
   - Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
   - Got rid of SH PFC hardcoded IRQ numbers.
   - Allwinner sunxi external interrupt through the "r" controller.
   - Moved the Cygnus driver to use DT-provided GPIO ranges.

  New drivers:

   - Atmel PIO4 pin controller for the SAMA4D2 family

  New subdrivers:

   - Rockchip RK3036 subdriver
   - Renesas SH PFC R8A7795 subdriver
   - Allwinner sunxi A83T PIO subdriver
   - Freescale i.MX7d iomux lpsr subdriver
   - Marvell Berlin BG4CT subdriver
   - SiRF Atlas 7 step B SoC subdriver
   - Intel Broxton SoC subdriver

  Apart from this, the usual slew if syntactic and semantic fixes"

* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
  pinctrl: pinconf: remove needless loop
  pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
  pinctrl: zynq: fix UTF-8 errors
  pinctrl: zynq: Initialize early
  pinctrl: at91: add missing of_node_put
  pinctrl: tegra-xusb: Correct lane mux options
  pinctrl: intel: Add Intel Broxton pin controller support
  pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
  pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
  drivers/pinctrl: Add the concept of an "init" state
  pinctrl: uniphier: set input-enable before pin-muxing
  pinctrl: cygnus: Add new compatible string for gpio controller driver
  pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
  pinctrl: cygnus: Optional DT property to support pin mappings
  pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
  pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
  pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
  pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
  pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
  usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
  ...

Add pinmuxing for external interrupt functionality through the
sun6i "r" pincontroller.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The r_pio gpio / pin controller has a pin_base of non 0, we need to
adjust for this before calling sunxi_pinctrl_desc_find_function_by_pin.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace all trivial request/free callbacks that do nothing but call into
pinctrl code with the generic versions.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Allwinner A83T soc port controller has 8 ports.
It has 3 IRQ banks namely PB, PG, PH.
Pinmuxing are different for some pins as compared to
sun8i A23 and A33.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

It's not needed an is just creating a null statement, so remove it.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The comment for PG14 mux setting 3 already correctly states that this
muxes PG13 to pwm1, but the text ascociated with it said uart3, fix this.

Note that we use "pwm" rather then "pwm1" to be consistent with pwm0
where the mux setting is also simply called "pwm" and to be consistent
with sun4i/sun7i which do the same.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>