* git://git.infradead.org/users/cbou/battery-2.6.31:
  Add ds2782 battery gas gauge driver
  olpc_battery: Ensure that the TRICKLE bit is checked
  olpc_battery: Fix up eeprom read function

direct access of driver_data is going away.

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds a driver for ds2782 battery devices.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

There are times when the battery is present but trickle charging,
and the EC sets only the TRICKLE bit. So we must check for the bit
when we're checking the charging/present status.

Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

The eeprom read function was placing values into the wrong place in
'buf'; we were starting from buf[off], rather than buf[0].

Also, the for loop that we were using was much uglier than it needed to
be.  This cleans it up a bit.

Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

There are cases when charging monitor and the event handler try to
change the charger state simultaneously. For instance, a charger is
connected to the system, there's the detection event and the event
handler tries to enable charging. It is possible that the periodic
charging monitor runs at the same time and it still thinks there's
no external charger. So it tries to disable the charging. As the
result, even if the conditions necessary to charge the battery hold,
there will be no actual charging.

The patch changes the event handler so that instead of enabling/
disabling the charger immediately it would rather make the monitor
run. The monitor code then decides what should be the charger state.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

The MAX17040 is a I2C interfaced Fuel Gauge systems for lithium-ion
batteries This patch adds support the MAX17040 Fuel Gauge

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

This adds support for ds2760's sleep mode feature. With this feature
enabled, the chip enters a deep sleep mode and disconnects from the
battery when the w1 line is held down for more than 2 seconds.

This new behaviour can be switched on and off using a new module
parameter.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

Removed struct ds2760_platform_data which wasn't defined anywhere.
Indentation cleanups.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

* git://git.infradead.org/battery-2.6:
  pda_power: Add optional OTG transceiver and voltage regulator support
  pcf50633_charger: Remove unused mbc_set_status function
  pcf50633_charger: Enable periodic charging restart