Pull pwm changes from Thierry Reding:
 "The patches for this release cycle include various enhancements
  (device tree support, better compile coverage, ...) for existing
  drivers.  There is a new driver for Atmel SoCs.

  Various drivers as well as the sysfs support received minor fixes and
  cleanups"

* tag 'pwm/for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: tiecap: Remove duplicate put_sync call
  pwm: tiehrpwm: use dev_err() instead of pr_err()
  pwm: pxa: remove unnecessary space before tabs
  pwm: ep93xx: split module author names
  pwm: use seq_puts() instead of seq_printf()
  pwm: atmel-pwm: Do not unprepare clock after successful registration
  of: Add Atmel PWM controller device tree binding
  pwm: atmel-pwm: Add Atmel PWM controller driver
  backlight: pwm_bl: Remove error message upon devm_kzalloc() failure
  pwm: pca9685: depends on I2C rather than REGMAP_I2C
  pwm: renesas-tpu: Enable driver compilation with COMPILE_TEST
  pwm: jz4740: Use devm_clk_get()
  pwm: jz4740: Pass device to clk_get()
  pwm: sysfs: Convert to use ATTRIBUTE_GROUPS macro
  pwm: pxa: Add device tree support

This is the other of the LP3943 MFD driver.
LP3943 can be used as a PWM generator, up to 2 channels.

* Two PWM generators supported

* Supported PWM operations
  request, free, config, enable and disable

* Pin assignment
  A driver data, 'pin_used' is checked when a PWM is requested.
  If the output pin is already assigned, then returns as failure.
  If the pin is available, 'pin_used' is set.
  When the PWM is not used anymore, then it is cleared.
  It is defined as unsigned long type for atomic bit operation APIs,
  but only LSB 16bits are used because LP3943 has 16 outputs.

Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add a PWM framework driver for the PWM controller found on Atmel SoCs.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[thierry.reding: coding style and other minor cleanups]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Remove the non-standard EP93xx PWM driver in drivers/misc and add
a new driver for the PWM controllers on the EP93xx platform based
on the PWM framework.

These PWM controllers each support 1 PWM channel with programmable
duty cycle, frequency, and polarity inversion.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The Timer Pulse Unit (TPU) is a 4-channels 16-bit timer used to generate
waveforms. This driver exposes PWM functions through the PWM API for
other drivers to use.

The code is loosely based on the leds-renesas-tpu driver by Magnus Damm
and the TPU PWM driver shipped in the Armadillo EVA 800 kernel sources.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Add a simple sysfs interface to the generic PWM framework.

  /sys/class/pwm/
  `-- pwmchipN/           for each PWM chip
      |-- export          (w/o) ask the kernel to export a PWM channel
      |-- npwm            (r/o) number of PWM channels in this PWM chip
      |-- pwmX/           for each exported PWM channel
      |   |-- duty_cycle  (r/w) duty cycle (in nanoseconds)
      |   |-- enable      (r/w) enable/disable PWM
      |   |-- period      (r/w) period (in nanoseconds)
      |   `-- polarity    (r/w) polarity of PWM (normal/inversed)
      `-- unexport        (w/o) return a PWM channel to the kernel

Based on work by Lars Poeschel.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Add pwm driver for the NXP pca9685 16 channel pwm-led controller.

The driver is really barebones at this stage. E.g. the OE' pin and
therefore the corresponding registers are not supported.
The driver was tested on a HW where this pin is tied to GND.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[thierry.reding@gmail.com: style and whitespace cleanups]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This patch adds a PWM driver based on Atmel Timer Counter Block. The
Timer Counter Block is used in Waveform generator mode.

A Timer Counter Block provides up to 6 PWM devices grouped by 2:
* group 0 = PWM 0 and 1
* group 1 = PWM 2 and 3
* group 2 = PMW 4 and 5

PWM devices in a given group must be configured with the same period
value. If a PWM device in a group tries to change the period value and
the other device is already configured with a different value an error
will be returned.

This driver requires device tree support. The Timer Counter Block number
used to create a PWM chip is given by the tc-block field in an
"atmel,tcb-pwm" compatible node.

This patch was tested on kizbox board (at91sam9g20 SoC) with pwm-leds.

Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

This driver only supported the Charging indicator LED.
New set of drivers going to provide support for both PWMs and LEDs for twl4030
and twl6030 series of PMICs.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

The driver supports the following LED outputs as generic PWM driver:
TWL4030 LEDA and LEDB (PWMA and PWMB)
TWL6030 Charging indicator LED (PWM LED)

On TWL6030 when the PWM requested LED is configured to be controlled by SW.
In this case the user can enable/disable and set the duty period freely.
When the PWM has been freed, the LED driver is put back to HW control.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>