The regulator module consists of 3 DCDCs and 8 LDOs. The output voltages are configurable and are meant to supply power to the main processor and other components Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk> Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The DB8500 has ePOD:s (electronic power domains) which are possible to switch on/off to deactivate silicon blocks on the DB8500 SoC by cutting their power without retention. We model these as simple regulators with one bit on/off settings. Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com> Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Signed-off-by: Martin Persson <martin.persson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a subdriver for the regulator found inside the TPS61050 and TPS61052 chips. Cc: Samuel Ortiz <samuel.ortiz@intel.com> Cc: Ola Lilja <ola.o.lilja@stericsson.com> Cc: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD. In this initial release, selecting voltages or current-limit and switching on/off the regulators are supported. Controlling voltages for DVS with GPIOs is not implemented fully and requires more considerations: it controls multiple bucks (selection of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO is activated, we lose the ability to control the voltage of a single buck regulator independently; i.e., contolling a buck affects other two bucks. Therefore, using the conventional regulator framework directly might be problematic. However, in this driver, we try to choose a setting without such side effect of affecting other regulators and then try to choose a setting with the minimum side effect (the sum of voltage changes in other regulators). On the other hand, controlling all the three bucks simultenously based on the voltage set table may help build cpufreq and similar system more robust; i.e., all the three voltages are consistent every time without glitches during transition. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
add support for mc13892, tested on mx51 babbage board Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Yong Shen <yong.shen@linaro.org> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
move some common functions and micros of mc13783 regulaor driver to a seperate file, which makes it possible for mc13892 to share code. Signed-off-by: Yong Shen <yong.shen@linaro.org> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TPS6524X provides three step-down converters and two general-purpose LDO voltage regulators. This device is interfaced using SPI. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow machine drivers to explicitly enable the use of the dummy regulator, enabling simpler support for systems with only a few specific supplies visible to software. It is strongly recommended that this is not used on systems with substantial software control over their PMICs, for maximum functionality constrints should be as fully specified as possible. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3972 PMIC. This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3972 PMIC controller uses I2C interface. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV with DVS support. In this initial release, users can set voltages for four DVS modes, RAMP delay values, and SYNC frequency. Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID is not supported in this release. If GPIO of EN is not valid in platform data, the driver assumes that it is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down VID0 and VID1 to fix DVS mode as 0 and disables DVS support. We assume that V_OUT is capable to provide every voltage from 770mV to 1.40V in 10mV steps although the data sheet has some ambiguity on it. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> -- v2: - Style correction - Can accept platform_data with invalid GPIOs - Removed unnecessary features - Improved error handling Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>