linux-toradex.git/drivers/regulator, branch v4.4.26 Linux kernel for Apalis and Colibri modules regulator: qcom_smd: Fix voltage ranges for pm8x41 2016-10-07T13:23:43+00:00 Stephen Boyd sboyd@codeaurora.org 2016-07-11T21:50:07+00:00 ba21aa15b9e5d3e5cff161c6a196df0df7b103f9 commit 290284776bb281759b11faa287b8abccaf74bfcb upstream. The voltage ranges listed here are wrong. The correct ranges can be seen in the "native" spmi regulator driver qcom_spmi-regulator.c at pldo_ranges[], ftsmps_ranges[] and boost_ranges[] for the pldo, ftsmps, and boost type regulators. Port these ranges over to the RPM SMD regulator driver so that we list the appropriate set of supported voltages on pldos. Doing this allows us to specify a voltage like 3075000 for l24, whereas before that wasn't a supported voltage. Fixes: da65e367b67e ("regulator: Regulator driver for the Qualcomm RPM") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reviewed-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 290284776bb281759b11faa287b8abccaf74bfcb upstream.

The voltage ranges listed here are wrong. The correct ranges can
be seen in the "native" spmi regulator driver
qcom_spmi-regulator.c at pldo_ranges[], ftsmps_ranges[] and
boost_ranges[] for the pldo, ftsmps, and boost type regulators.
Port these ranges over to the RPM SMD regulator driver so that we
list the appropriate set of supported voltages on pldos.

Doing this allows us to specify a voltage like 3075000 for l24,
whereas before that wasn't a supported voltage.

Fixes: da65e367b67e ("regulator: Regulator driver for the Qualcomm RPM")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941 2016-10-07T13:23:43+00:00 Stephen Boyd stephen.boyd@linaro.org 2016-06-26T05:52:12+00:00 efc6dc794c205c255521fa0364ab6a1e7389b07e commit 93bfe79b03365f410aa91caf04263173c008ecdf upstream. The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on some datasheets. Let's rename them to match the datasheets and also match the RPM based regulator driver which calls these by their 5vs names (see qcom_smd-regulator.c). There aren't any users of these regulators so far, so there aren't any concerns of DT ABI breakage here. While we're here making updates to the switches, also mandate usage of the OCP irq for these switches too. Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver") Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 93bfe79b03365f410aa91caf04263173c008ecdf upstream.

The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: qcom_spmi: Add support for get_mode/set_mode on switches 2016-10-07T13:23:43+00:00 Stephen Boyd stephen.boyd@linaro.org 2016-06-26T05:52:13+00:00 d23a7a00c1523c23a0d5b08113c150ac89158f1a commit 919163f6362ac23138d31fc8befdd52e5d7e488d upstream. The voltage switches support mode switching, so add support for these ops to those types of regulators. Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver") Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 919163f6362ac23138d31fc8befdd52e5d7e488d upstream.

The voltage switches support mode switching, so add support for
these ops to those types of regulators.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: qcom_spmi: Add support for S4 supply on pm8941 2016-10-07T13:23:43+00:00 Stephen Boyd stephen.boyd@linaro.org 2016-06-26T05:52:11+00:00 7ad9ee6558f65c9d4e840b12e73fb39f2df656c0 commit c333dfe8dba7d3e47e97e1cee3c38123e19ae73c upstream. The S4 supply is sometimes called the boost regulator because it outputs 5V. Typically it's connected to the 5vs1 and 5vs2 switches for use in USB OTG and HDMI applications. Add support for this regulator which was mistakenly left out from the initial submission of this driver. Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver") Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c333dfe8dba7d3e47e97e1cee3c38123e19ae73c upstream.

The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: anatop: allow regulator to be in bypass mode 2016-09-15T06:27:54+00:00 Mika Båtsman mbatsman@mvista.com 2016-06-17T10:31:37+00:00 3838b04f6d5868f5ec5ee52ce1391b6253c6ce16 commit 8a092e682f20f193f2070dba2ea1904e95814126 upstream. Bypass support was added in commit d38018f2019c ("regulator: anatop: Add bypass support to digital LDOs"). A check for valid voltage selectors was added in commit da0607c8df5c ("regulator: anatop: Fail on invalid voltage selector") but it also discards all regulators that are in bypass mode. Add check for the bypass setting. Errors below were seen on a Variscite mx6 board. anatop_regulator 20c8000.anatop:regulator-vddcore@140: Failed to read a valid default voltage selector. anatop_regulator: probe of 20c8000.anatop:regulator-vddcore@140 failed with error -22 anatop_regulator 20c8000.anatop:regulator-vddsoc@140: Failed to read a valid default voltage selector. anatop_regulator: probe of 20c8000.anatop:regulator-vddsoc@140 failed with error -22 Fixes: da0607c8df5c ("regulator: anatop: Fail on invalid voltage selector") Signed-off-by: Mika Båtsman <mbatsman@mvista.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 8a092e682f20f193f2070dba2ea1904e95814126 upstream.

Bypass support was added in commit d38018f2019c ("regulator: anatop: Add
bypass support to digital LDOs"). A check for valid voltage selectors was
added in commit da0607c8df5c ("regulator: anatop: Fail on invalid voltage
selector") but it also discards all regulators that are in bypass mode. Add
check for the bypass setting. Errors below were seen on a Variscite mx6
board.

anatop_regulator 20c8000.anatop:regulator-vddcore@140: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddcore@140 failed with error -22
anatop_regulator 20c8000.anatop:regulator-vddsoc@140: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddsoc@140 failed with error -22

Fixes: da0607c8df5c ("regulator: anatop: Fail on invalid voltage selector")
Signed-off-by: Mika Båtsman <mbatsman@mvista.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: axp20x: Fix axp22x ldo_io voltage ranges 2016-05-19T00:06:51+00:00 Hans de Goede hdegoede@redhat.com 2016-04-27T13:59:27+00:00 b657027854182f708d74424998fe95624f7c69c4 commit a2262e5a12e05389ab4c7fc5cf60016b041dd8dc upstream. The minium voltage of 1800mV is a copy and paste error from the axp20x regulator info. The correct minimum voltage for the ldo_io regulators on the axp22x is 700mV. Fixes: 1b82b4e4f954 ("regulator: axp20x: Add support for AXP22X regulators") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a2262e5a12e05389ab4c7fc5cf60016b041dd8dc upstream.

The minium voltage of 1800mV is a copy and paste error from the axp20x
regulator info. The correct minimum voltage for the ldo_io regulators
on the axp22x is 700mV.

Fixes: 1b82b4e4f954 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: s2mps11: Fix invalid selector mask and voltages for buck9 2016-05-19T00:06:51+00:00 Krzysztof Kozlowski k.kozlowski@samsung.com 2016-03-28T04:09:56+00:00 fc2d8c98f754993f0c66d373672418a503e6e299 commit 3b672623079bb3e5685b8549e514f2dfaa564406 upstream. The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff instead of 0x1f) thus reading entire register as buck9's voltage. This effectively caused regulator core to interpret values as higher voltages than they were and then to set real voltage much lower than intended. The buck9 provides power to other regulators, including LDO13 and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower voltage caused SD card detection errors on Odroid XU3/XU4: mmc1: card never left busy state mmc1: error -110 whilst initialising SD card During driver probe the regulator core was checking whether initial voltage matches the constraints. With incorrect vsel_mask of 0xff and default value of 0x50, the core interpreted this as 5 V which is outside of constraints (3-3.775 V). Then the regulator core was adjusting the voltage to match the constraints. With incorrect vsel_mask this new voltage mapped to a vere low voltage in the driver. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3b672623079bb3e5685b8549e514f2dfaa564406 upstream.

The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.

The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
	mmc1: card never left busy state
	mmc1: error -110 whilst initialising SD card

During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: s5m8767: fix get_register() error handling 2016-05-04T21:48:50+00:00 Arnd Bergmann arnd@arndb.de 2016-02-16T14:53:11+00:00 72291d619e2928556db1d446f0b4afff330276a7 commit e07ff9434167981c993a26d2edbbcb8e13801dbb upstream. The s5m8767_pmic_probe() function calls s5m8767_get_register() to read data without checking the return code, which produces a compile-time warning when that data is accessed: drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe': drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized] drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized] This changes the s5m8767_get_register() function to return a -EINVAL not just for an invalid register number but also for an invalid regulator number, as both would result in returning uninitialized data. The s5m8767_pmic_probe() function is then changed accordingly to fail on a read error, as all the other callers of s5m8767_get_register() already do. In practice this probably cannot happen, as we don't call s5m8767_get_register() with invalid arguments, but the gcc warning seems valid in principle, in terms writing safe error checking. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 9c4c60554acf ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap") Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e07ff9434167981c993a26d2edbbcb8e13801dbb upstream.

The s5m8767_pmic_probe() function calls s5m8767_get_register() to
read data without checking the return code, which produces a compile-time
warning when that data is accessed:

drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized]

This changes the s5m8767_get_register() function to return a -EINVAL
not just for an invalid register number but also for an invalid
regulator number, as both would result in returning uninitialized
data. The s5m8767_pmic_probe() function is then changed accordingly
to fail on a read error, as all the other callers of s5m8767_get_register()
already do.

In practice this probably cannot happen, as we don't call
s5m8767_get_register() with invalid arguments, but the gcc
warning seems valid in principle, in terms writing safe
error checking.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c4c60554acf ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: core: Fix nested locking of supplies 2016-05-04T21:48:50+00:00 Thierry Reding treding@nvidia.com 2015-12-02T15:54:50+00:00 5a58f809d731c23c0b898d2021903db8dee4466f commit 70a7fb80e85ae7f78f8e90cec3fbd862ea6a4d4b upstream. Commit fa731ac7ea04 ("regulator: core: avoid unused variable warning") introduced a subtle change in how supplies are locked. Where previously code was always locking the regulator of the current iteration, the new implementation only locks the regulator if it has a supply. For any given power tree that means that the root will never get locked. On the other hand the regulator_unlock_supply() will still release all the locks, which in turn causes the lock debugging code to warn about a mutex being unlocked which wasn't locked. Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Fixes: fa731ac7ea04 ("regulator: core: avoid unused variable warning") Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 70a7fb80e85ae7f78f8e90cec3fbd862ea6a4d4b upstream.

Commit fa731ac7ea04 ("regulator: core: avoid unused variable warning")
introduced a subtle change in how supplies are locked. Where previously
code was always locking the regulator of the current iteration, the new
implementation only locks the regulator if it has a supply. For any
given power tree that means that the root will never get locked.

On the other hand the regulator_unlock_supply() will still release all
the locks, which in turn causes the lock debugging code to warn about a
mutex being unlocked which wasn't locked.

Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Fixes: fa731ac7ea04 ("regulator: core: avoid unused variable warning")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator: core: Ensure we lock all regulators 2016-05-04T21:48:50+00:00 Mark Brown broonie@kernel.org 2015-12-01T15:51:52+00:00 29c9f634cb132107df3e4f07c8e48b35d04b527b commit 49a6bb7a1c0963f260e4b0dcc2c0e56ec65a28b2 upstream. The latest workaround for the lockdep interface's not using the second argument of mutex_lock_nested() changed the loop missed locking the last regulator due to a thinko with the loop termination condition exiting one regulator too soon. Reported-by: Tyler Baker <tyler.baker@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 49a6bb7a1c0963f260e4b0dcc2c0e56ec65a28b2 upstream.

The latest workaround for the lockdep interface's not using the second
argument of mutex_lock_nested() changed the loop missed locking the last
regulator due to a thinko with the loop termination condition exiting
one regulator too soon.

Reported-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>