Pull remoteproc updates from Bjorn Andersson:
 "This exposes the remoteproc's name in sysfs, allows stm32 to enter
  platform standby and provides bug fixes for stm32 and Qualcomm's modem
  remoteproc drivers. Finally it updates MAINTAINERS to reflect the move
  to kernel.org"

* tag 'rproc-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
  MAINTAINERS: remoteproc: update git tree location
  remoteproc: Remove dev_err() usage after platform_get_irq()
  remoteproc: stm32: manage the get_irq probe defer case
  remoteproc: stm32: clear MCU PDDS at firmware start
  remoteproc: qcom: q6v5-mss: fixup q6v5_pds_enable error handling
  remoteproc: Add a sysfs interface for name
  remoteproc: qcom: Move glink_ssr notification after stop

Remoteproc started using dma_declare_coherent_memory recently, which is
a bad idea from drivers, and the maintainers agreed to fix that.  But
until that is fixed only allow building the driver built in so that we
can remove the dma_declare_coherent_memory export and prevent other
drivers from "accidentally" using it like remoteproc.  Note that the
driver would also leak the declared coherent memory on unload if it
actually was built as a module at the moment.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Manage the -EPROBE_DEFER error case for "wdg" IRQ.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

When remoteproc stops a firmware, it sets the MCU PDDS flag, allowing
the platform to reach the Standby power mode if needed.
Symmetrically, clear this flag before running a firmware.
This fixes the issue where the system goes to Standby mode when the
MCU crashes while MPU is in CSTOP mode.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

dev_pm_domain_attach_by_name will return NULL if the requested
power-domain is not a part device node. This could result in
NULL pointer de-reference in q6v5_pds_enable. Fix this by
checking for IS_ERR_OR_NULL and forward the appropriate error
code.

Fixes: 4760a896be88e ("remoteproc: q6v5-mss: Vote for rpmh power domains")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This patch adds a sysfs interface that provides the name of the
remote processor to userspace. This allows the userspace to identify
a remote processor as the remoteproc devices themselves are created
based on probe order and can change from one boot to another or
at runtime.

The name is made available in debugfs originally, and is being
retained for now. This can be cleaned up after couple of releases
once users get familiar with the new interface.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

glink_ssr is used to signal a remote processor "A" about the stopping of
another remote processor "B", so that in the event that remote processor
B is ever booted again the fifos of the glink channel between A and B is
in a known state.

But if remote processor A receives this notification before B is
actually stopped the newly reset fifo indices will be interpreted as
there being "data" on the channel and either side of the channel will
enter a fatal error handler.

Move the glink_ssr notification to the "unprepare" state of the
rproc_subdev to avoid this issue.

This has the side effect of us not notifying the dying remote processor
itself about its fate, which has been seen to block in certain resource
constraint scenarios.

Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Pull remoteproc updates from Bjorn Andersson:
 "This adds support for the STM32 remoteproc, additional i.MX platforms
  with Cortex M4 remoteprocs and Qualcomm's QCS404 Compute DSP.

  Also initial support for vendor specific resource table entries and
  support for unprocessed Qualcomm firmware files"

* tag 'rproc-v5.3' of git://github.com/andersson/remoteproc:
  remoteproc: stm32: fix building without ARM SMCC
  remoteproc: qcom: q6v5-mss: Fix build error without QCOM_MDT_LOADER
  remoteproc: copy parent dma_pfn_offset for vdev
  remoteproc: qcom: q6v5-mss: Support loading non-split images
  soc: qcom: mdt_loader: Support loading non-split images
  remoteproc: stm32: add an ST stm32_rproc driver
  dt-bindings: remoteproc: add bindings for stm32 remote processor driver
  dt-bindings: stm32: add bindings for ML-AHB interconnect
  remoteproc: Use struct_size() helper
  remoteproc: add vendor resources handling
  remoteproc: imx: Fix typo in "failed"
  remoteproc: imx: Broaden the Kconfig selection logic
  remoteproc,rpmsg: add missing MAINTAINERS file entries
  remoteproc: qcom: qdsp6-adsp: Add support for QCS404 CDSP
  dt-bindings: remoteproc: Rename and amend Hexagon v56 binding

When compile testing this driver without SMCC support enabled,
we get a link error:

drivers/remoteproc/stm32_rproc.o: In function `stm32_rproc_start':
stm32_rproc.c:(.text+0x776): undefined reference to `__arm_smccc_smc'
drivers/remoteproc/stm32_rproc.o: In function `stm32_rproc_stop':
stm32_rproc.c:(.text+0x92c): undefined reference to `__arm_smccc_smc'

Make the actual call to arm_smccc_smc conditional on the Kconfig
symbol controlling its implementation.

Fixes: 13140de09cc2 ("remoteproc: stm32: add an ST stm32_rproc driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>