ip_finish_output_gso() may call .ndo_features_check() even before the
skb has a L2 header. This conflicts with qeth_get_ip_version()'s attempt
to inspect the L2 header via vlan_eth_hdr().

Switch to vlan_get_protocol(), as already used further down in the
common qeth_features_check() path.

Fixes: f13ade199391 ("s390/qeth: run non-offload L3 traffic over common xmit path")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Due to insufficient locking, qeth_core_set_online() and
qeth_dev_layer2_store() can run in parallel, both attempting to load &
setup the discipline (and stepping on each other toes along the way).
A similar race can also occur between qeth_core_remove_device() and
qeth_dev_layer2_store().

Access to .discipline is meant to be protected by the discipline_mutex,
so add/expand the locking in qeth_core_remove_device() and
qeth_core_set_online().
Adjust the locking in qeth_l*_remove_device() accordingly, as it's now
handled by the callers in a consistent manner.

Based on an initial patch by Ursula Braun.

Fixes: 9dc48ccc68b9 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When qeth_dev_layer2_store() - holding the discipline_mutex - waits
inside qeth_l*_remove_device() for a qeth_do_reset() thread to complete,
we can hit a deadlock if qeth_do_reset() concurrently calls
qeth_set_online() and thus tries to aquire the discipline_mutex.

Move the discipline_mutex locking outside of qeth_set_online() and
qeth_set_offline(), and turn the discipline into a parameter so that
callers understand the dependency.

To fix the deadlock, we can now relax the locking:
As already established, qeth_l*_remove_device() waits for
qeth_do_reset() to complete. So qeth_do_reset() itself is under no risk
of having card->discipline ripped out while it's running, and thus
doesn't need to take the discipline_mutex.

Fixes: 9dc48ccc68b9 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull block fixes from Jens Axboe:
 "A few stragglers in here, but mostly just straight fixes. In
  particular:

   - Set of rnbd fixes for issues around changes for the merge window
     (Gioh, Jack, Md Haris Iqbal)

   - iocost tracepoint addition (Baolin)

   - Copyright/maintainers update (Christoph)

   - Remove old blk-mq fast path CPU warning (Daniel)

   - loop max_part fix (Josh)

   - Remote IPI threaded IRQ fix (Sebastian)

   - dasd stable fixes (Stefan)

   - bcache merge window fixup and style fixup (Yi, Zheng)"

* tag 'block-5.11-2020-12-23' of git://git.kernel.dk/linux-block:
  md/bcache: convert comma to semicolon
  bcache:remove a superfluous check in register_bcache
  block: update some copyrights
  block: remove a pointless self-reference in block_dev.c
  MAINTAINERS: add fs/block_dev.c to the block section
  blk-mq: Don't complete on a remote CPU in force threaded mode
  s390/dasd: fix list corruption of lcu list
  s390/dasd: fix list corruption of pavgroup group list
  s390/dasd: prevent inconsistent LCU device data
  s390/dasd: fix hanging device offline processing
  blk-iocost: Add iocg idle state tracepoint
  nbd: Respect max_part for all partition scans
  block/rnbd-clt: Does not request pdu to rtrs-clt
  block/rnbd-clt: Dynamically allocate sglist for rnbd_iu
  block/rnbd: Set write-back cache and fua same to the target device
  block/rnbd: Fix typos
  block/rnbd-srv: Protect dev session sysfs removal
  block/rnbd-clt: Fix possible memleak
  block/rnbd-clt: Get rid of warning regarding size argument in strlcpy
  blk-mq: Remove 'running from the wrong CPU' warning

Pull more s390 updates from Heiko Carstens:
 "This is mainly to decouple udelay() and arch_cpu_idle() and simplify
  both of them.

  Summary:

   - Always initialize kernel stack backchain when entering the kernel,
     so that unwinding works properly.

   - Fix stack unwinder test case to avoid rare interrupt stack
     corruption.

   - Simplify udelay() and just let it busy loop instead of implementing
     a complex logic.

   - arch_cpu_idle() cleanup.

   - Some other minor improvements"

* tag 's390-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/zcrypt: convert comma to semicolon
  s390/idle: allow arch_cpu_idle() to be kprobed
  s390/idle: remove raw_local_irq_save()/restore() from arch_cpu_idle()
  s390/idle: merge enabled_wait() and arch_cpu_idle()
  s390/delay: remove udelay_simple()
  s390/irq: select HAVE_IRQ_EXIT_ON_IRQ_STACK
  s390/delay: simplify udelay
  s390/test_unwind: use timer instead of udelay
  s390/test_unwind: fix CALL_ON_STACK tests
  s390: make calls to TRACE_IRQS_OFF/TRACE_IRQS_ON balanced
  s390: always clear kernel stack backchain before calling functions

In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.

The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.

If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.

Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.

Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.

Example: device A and B are in the same pavgroup.

Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.

In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.

When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.

Fix by setting private->pavgroup to NULL in dasd_add_device.

If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.

Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Prevent _lcu_update from adding a device to a pavgroup if the LCU still
requires an update. The data is not reliable any longer and in parallel
devices might have been moved on the lists already.
This might lead to list corruptions or invalid PAV grouping.
Only add devices to a pavgroup if the LCU is up to date. Additional steps
are taken by the scheduled lcu update.

Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.

In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.

Commit 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.

Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.

Fixes: 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration")
Cc: stable@vger.kernel.org #5.3
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull VFIO updates from Alex Williamson:

 - Fix uninitialized list walk in error path (Eric Auger)

 - Use io_remap_pfn_range() (Jason Gunthorpe)

 - Allow fallback support for NVLink on POWER8 (Alexey Kardashevskiy)

 - Enable mdev request interrupt with CCW support (Eric Farman)

 - Enable interface to iommu_domain from vfio_group (Lu Baolu)

* tag 'vfio-v5.11-rc1' of git://github.com/awilliam/linux-vfio:
  vfio/type1: Add vfio_group_iommu_domain()
  vfio-ccw: Wire in the request callback
  vfio-mdev: Wire in a request handler for mdev parent
  vfio/pci/nvlink2: Do not attempt NPU2 setup on POWER8NVL NPU
  vfio-pci: Use io_remap_pfn_range() for PCI IO memory
  vfio/pci: Move dummy_resources_list init in vfio_pci_probe()